Abstract:Not only directionally solidified but also refined microstructure was realized in laser melting deposited Nb–Si–Ti alloys.For the DS microstructure, the <100> of NbSS and <110> of (Nb, Ti)3Si tend to be parallel to the LMD building direction.The fracture toughness of the as-deposited sample is up to 20.3 MPa·m1/2.The LMD processing condition resulted in the transformation of fracture mode from cleavage to dimple for NbSS phases.The phenomenon of crack propagation in (Nb, Ti)3Si and crack stopping at NbSS dendrite was observed.Aiming at achieving fine and directionally-solidified microstructure of Nb–Si based alloy, Nb, Si and Ti powder particles were utilized as the raw materials, and laser melting deposition (LMD) experiments were conducted with 1500 W and 2000 W laser power, respectively. The microstructure characteristic, micro-hardness, and indentation fracture toughness were examined by scanning electron microscope (SEM), X-ray energy dispersive spectrometer (XEDS) and X-ray diffraction (XRD). The results showed that the two kinds of as-deposited Nb–17Si–23Ti alloy samples were mainly composed of NbSS, (Nb, Ti)3Si and Ti-rich NbSS, and the microstructure presents rapid directionally-solidified characteristic, in which the <100> crystallographic direction of NbSS and <110> crystallographic direction of (Nb, Ti)3Si tend to be parallel to the LMD building direction. With the laser power increasing from 1500 W to 2000 W, the microstructure became more oriented and homogeneous. For the sample at 2000 W, the dendrite spacing was only about 1–2 μm, and NbSS and (Nb, Ti)3Si couples grow alternately and they are parallel to the building direction strictly. In the meantime the micro-hardness and indentation fracture toughness reached 1075 HV and 20.3 MPa·m1/2, respectively, indicating significant improvement by the directional growth of fine NbSS and (Nb, Ti)3Si phases, and the dimple fracture mode of the NbSS dendrites.<ol class="links-for-figure"><li><a class="anchor download-link u-font-sans" href="https://ars.els-cdn.com/content/image/1-s2.0-S1002007120305773-fx1_lrg.jpg">Download : Download high-res image (365KB)</a></li><li><a class="anchor download-link u-font-sans" href="https://ars.els-cdn.com/content/image/1-s2.0-S1002007120305773-fx1.jpg">Download : Download full-size image</a></li></ol>

Unidirectional Solidification of a Nbss/Nb5Si3 In-Situ Composite

Effect of Directional Solidification Methods on Solid Solution Window in Ni-based Single-Crystal Superalloy

Microstructure evolution and solidification behaviour of Nb–16Si–22Ti–2Cr–2Al–6Hf alloy processed by directional solidification

MICROSTRUCTURAL CHARACTERISTICS AND MECHANICAL PROPERTIES OF A Nb/Nb5Si3 BASED COMPOSITE WITH AND WITHOUT DIRECTIONAL SOLIDIFICATION

Effect of Growth Rate on Microstructure and Mechanical Properties in a Directionally Solidified Nb-silicide Base Alloy

Microstructural and mechanical characterization of Nb-based in situ composites from Nb–Si–Ti ternary system

Microstructure Evolution and Mechanical Properties of a Directionally Solidified Nb-Ti-Si-Cr-Al-Hf-Dy Alloy

Behaviors and interactions of strengthening and constraint for ductile Nbss matrix in Nb–Si based alloys

Microstructure Evolution and Toughening Mechanism of a Nb-18Si-5HfC Eutectic Alloy Created by Selective Laser Melting

The balance of mechanical and environmental properties of a multielement niobium-niobium silicide-basedIn Situ composite

Microstructural Investigations of Ni-Based Superalloys by Directional Solidification Quenching Technique

Analyses of Eutectoid Phase Transformations in Nb–Silicide In Situ Composites

Microstructure and segregation behaviour of directionally solidified tungsten bearing 25Cr-35Ni-Nb heat-resistant stainless steels

A Study of the Effects of Hf and Sn on the Microstructure, Hardness and Oxidation of Nb-18Si Silicide-Based Alloys-RM(Nb)ICs with Ti Addition and Comparison with Refractory Complex Concentrated Alloys (RCCAs)

Achieving an appropriate strength-ductility synergy of Nbss/Nb5Si3 in situ composites governed by gradient annealing heat treatment

On the Microstructure and Properties of Nb-12Ti-18Si-6Ta-2.5W-1Hf (at.%) Silicide-Based Alloys with Ge and Sn Additions

On the Orientation Relationship Between Ti5Si3 Precipitates and B2 Phase in a Ti-47Al-2W-0.5Si Alloy

Rapid directionally solidified microstructure characteristic and fracture behaviour of laser melting deposited Nb–Si–Ti alloy

Investigation of macro/microstructure evolution and mechanical properties of directionally solidified high-Nb TiAl-based alloy

In-Situ Observation of Ni-11.5wt%Si Eutectic Microstructure Evolution and Exploration of Strengthening Mode of Ni-Ni3si Eutectic Composites

Effects of the microstructure and minor elements on the fracture toughness of Nb-Si alloy