Abstract:In this study, we investigated the effects of nanostructured composite powders (WC-Ni), nickel binder content, and sintering techniques on the morphology and mechanical properties of tungsten carbide. An alternative low-temperature gas-solid reaction route with a short reaction time was employed to produce nanostructured composite powders with 5 and 15 wt% Ni. The powders were consolidated using spark plasma sintering (SPS) and conventional vacuum furnace sintering at temperatures of 1350 °C and 1450 °C. The composite powders were characterized using scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), and particle size measurements. The expansion/contraction of the compacted nanocomposite powders was studied through dilatometric analysis. The composite powders exhibited a uniform distribution of Ni, in both compositions. For the WC-5 wt% Ni nanocomposite powders, the average crystallite sizes for WC and Ni were 41.6 nm and 46.2 nm, respectively. While, for the WC-15 wt% Ni nanocomposite, the crystallite sizes for WC and Ni were 45.6 and 38.4 nm. The sintered composites were evaluated through XRD, SEM, measurements of density and Vickers hardness. The enhanced sinterability of the nanostructured powders enabled their consolidation into (WC-Ni) hard metal with densities approaching the theoretical relative density of 96.07 %, even with low binder content (5 wt% Ni). This is attributed to the uniform distribution of Ni and an extensive Ni-WC interface present prior to sintering. The SPS process at 1350 °C produced sintered bodies (WC-5 wt% Ni and WC-15 wt% Ni) with higher Vickers hardness (2322 HV and 1512 HV, respectively) and superior microstructural quality compared to samples produced by conventional vacuum furnace techniques. These results demonstrated that the mechanical properties of the system WC-Ni processed by SPS are superior to those obtained by vacuum furnace. Therefore, WC-Ni hard metals processed by this approach is a promising alternative to conventional hard metals (WC-Co) for a wide range of applications.

Sintering Of Nanostructured Tungsten-Base Composites

Long-term Ball Milling and Hot Pressing of In-Situ Nanoscale Tungsten Carbides Reinforced Copper Composite and Its Characterization

Microstructure and Properties of In-Situ TiC Reinforced Copper Nanocomposites Fabricated Via Long-Term Ball Milling and Hot Pressing

Microstructure and mechanical properties of liquid–phase sintered W@NiFe composite powders

Fabrication of nanocrystalline supersaturated W–Al alloys with enhanced thermal stability and high sinterability

Development of Tungsten-Based Materials by Different Sintering Techniques

Preparation of Ti/Al based nanophase composite powder by mechanical alloying

Tungsten heavy alloy: Nano-crystallinity and alloying induced low temperature sintering, microstructure and mechanical properties

Microstructural and Mechanical Characterization of Colloidal Processed WC/(W5Vol%Ni) via Spark Plasma Sintering

Enhanced properties of hard metal WC-Ni processed from nanostructured powders

Fabrication and Characterization of Tungsten Heavy Alloys with High W Content by Powder Metallurgy

Effect of sintering temperature on fine-grained Cu W composites with high copper

Microstructural characteristics, mechanical properties and interfacial formation mechanism of tungsten alloy/steel composite structure fabricated by HIP co-sintering

Microstructure and high-temperature mechanical properties of Cu-W composite prepared by hot isostatic pressing

Preparation and Sintering Performance of W-Ni/Yb2O3 Composite Materials

Fabrication of Ni/Sic Composite Powder by Mechanical Alloying and Its Effects on Properties of Copper Matrix Composites

Effect of nano-Y2O3 on the microstructure and mechanical properties of Cu-10W composites prepared by spark plasma sintering

Sintering Behavior of W–30Cu Composite Powder Prepared by Electroless Plating

Ni composites reinforced with ultrafine and uniform TiCx and Cr3C2 particles in situ: Enhanced properties and a well-matched interface

Performance of a Hierarchically Nanostructured W–Cu Composite Produced via Mediating Phase Separation

Effect of ZrC nano-powder addition on the microstructure and mechanical properties of binderless tungsten carbide fabricated by spark plasma sintering