Abstract:Phase change materials (PCMs) exhibit considerable potential for utilization in energy storage and temperature regulation applications, primarily attributed to their notable latent heat capacity . Nevertheless, the intrinsically limited thermal conductivity of PCMs necessitates the use of thermal conductivity enhancers (TCEs) that possess adjustable features to compensate for greater heat storage efficiency. Porous structures with flexible design freedom have garnered growing interest in contrast to traditional random foams, owing to their significantly larger surface areas and fully interconnected pore networks. This study fabricated three polar form-designed triply periodic minimal surfaces (TPMS) porous structures using selective laser melting (SLM) based on various radial density gradients , namely the uniform density, the linear gradient, and the Boltzmann gradient. The TPMS porous structures were incorporated as TCEs within a paraffin matrix to form composite TPMS-PCMs. The melting behavior of composite TPMS-PCMs during the charging process was investigated by employing both visual experiments and numerical methods. A thorough analysis was undertaken regarding the progression of solid-liquid phase interfaces, temperature distribution, convection distribution, and heat storage rate to elucidate the mechanisms that contribute to enhanced heat transfer. The findings indicate that the configuration of the density gradient has a notable impact on the melting behavior of composite TPMS-PCMs by tuning heat transfer paths. The heat storage rate of the linear gradient case is the highest among the three, reaching 12.1 W, 1.6 times that of the uniform density case, and twice that of the Boltzmann gradient case. Although the Boltzmann gradient case has the lowest heat storage rate, it demonstrates exceptional performance in terms of temperature uniformity. The average temperature gradient along the radius during melting is 348.6 °C/m, which is only 59% observed in the linear gradient case and 56% in the uniform density case. These findings substantiate the effectiveness of the radial gradient density design in the control of the thermal storage process of composite TPMS-PCMs. They serve as a reference for optimizing thermal storage and temperature control systems that rely on latent heat storage in the future.

Study on pp/talc flat polymeic gradient materials-(II) Performance

THE STUDY ON PP/Talc FLAT POLYMEIC GRADIENT MATERIALS--(Ⅱ) PERFORMANCE

A New Technique for Fabrication of Flat Pp/Talc Graded Material

Study on thermal stability of PP/MMT nanocomposites

A Flat Polymeric Gradient Material: Preparation, Structure and Property

Effects Of Talcum Powder(Talc) And Compounding Sequence On The Morphology And Mechanical Properties Of Pa6/Pp/Mapp Blend

A New Technique for Preparing a Filled Type of Polymeric Gradient Material

Evaluation of mechanical properties of Ni/BaTiO3 functionally graded material

Effects of TiB2 content and gradient structure on microstructural characterization and mechanical properties of TiB2/Al7050 composites

Effect of transverse gradient extrusion process on texture and mechanical properties of Mg–3Al–1Zn alloy sheets

TiB<sub>2</sub>/AlN/Cu Functionally Graded Materials (fgms) Fabricated by Spark Plasma Sintering (SPS) Method

Polypropylene/montmorillonite nanocomposites I. Preparation, characterizsation and dynamic mechnical properties

The Influence of Melt Temperature on the Crystal Orientation of Polypropylene Containing Talc

Fabrication of dual-gradient microstructure and their effects on the mechanical properties of commercial pure Ti

Structure and Magnetostriction of (dy0.6tb0.3pr0.1)(fe0.95−xmn0.05gax)1.85 Alloys

Processing and properties of gamma TiAl sheet from atomized powder

Analysis of thermal storage behavior of composite phase change materials embedded with gradient-designed TPMS thermal conductivity enhancers: A numerical and experimental study

Mechanical properties of three-dimensional functionally graded TPMS structures

TiB<sub>2</sub>/AlN/Cu Functionally Graded Materials (FGMs) Fabricated by Spark Plasma Sintering (SPS) Method

Strain Hardening and Tensile Behaviors of Gradient Structure Mg Alloys with Different Orientation Relationships

Research on PA66/PET/Talc Composite