Abstract:A new lower tungsten divertor has been developed and installed in the EAST superconducting tokamak to replace the previous graphite divertor with power handling capability increasing from <2 MW m−2 to ∼10 MW m−2, aiming at achieving long-pulse H-mode operations in a full metal wall environment with the steady-state divertor heat flux of ∼10 MW m−2. A new divertor concept, ‘corner slot’ (CS) divertor, has been employed. By using the ‘corner effect’, a strongly dissipative divertor with the local buildup of high neutral pressure near the corner can be achieved, so that stable detachment can be maintained across the entire outer target plate with a relatively lower impurity seeding rate, at a separatrix density compatible with advanced steady-state core scenarios. These are essential for achieving efficient current drive with low-hybrid waves, a low core impurity concentration and thus a low loop voltage for fully non-inductive long-pulse operations. Compared with the highly closed small-angle-slot divertor in DIII-D, the new divertor in EAST exhibits the following merits: (1) a much simpler geometry with integral cassette body structure, combining vertical and horizontal target plates, which are more suitable for actively water-cooled W/Cu plasma facing components, facilitating installation precision control for minimizing surface misalignment, achieving high engineering reliability and lowering the capital cost as well; (2) it has much greater flexibility in magnetic configurations, allowing for the position of the outer strike point on either vertical or horizontal target plates to accommodate a relatively wide triangularity range, δ l = 0.4–0.6, thus enabling to explore various advanced scenarios. A water-cooled copper in-vessel coil has been installed under the dome. Five supersonic molecular beam injection systems have been mounted in the divertor to achieve faster and more precise feedback control of the gas injection rate. Furthermore, this new divertor allows for double null divertor operation and slowly sweeping the outer strike point across the horizontal and vertical target plates to spread the heat flux for long-pulse operations. Preliminary experimental results demonstrate the ‘corner effect’ and are in good agreement with simulations using SOLPS-ITER code including drifts. The EAST new divertor provides a test-bed for the closed divertor concept to achieve steady-state detachment operation at high power. Next step, a more closed divertor, ‘sharp-cornered slot’ divertor, building upon the current CS divertor concept, has been proposed as a candidate for the EAST upper divertor upgrade.

The batch production for superconducting magnet coils of EAST (HT-7U)

35 Kj/7 Kw Conduction-cooled High Tc Superconducting Magnet Energy Storage

Recent Progress in Chinese Fusion Research Based on Superconducting Tokamak Configuration

Development of a Conduction-Cooled HTS SMES

Fully Active Cooled In-vessel Components of EAST Tokamak

Power Supply System of EAST Superconducting Tokamak

Development of a compact torus injector system for central fuelling technology of EAST

Design and Test Results for the Pf Power Supply System of East

Power Balance Investigation in Long-Pulse High-Performance Discharges with ITER-like Tungsten Divertor on EAST

Progress of the ITER Correction Coils in China

Stepped-shape Field Winding Optimization of a Large Capacity HTS Aircraft Propulsion Machine

Manufacture and Testing of Pre-prototype HTS Twisted Stack Slotted-Core Cable

Physics Design of New Lower Tungsten Divertor for Long-Pulse High-Power Operations in EAST

Mechanical effects: challenges for high-field superconducting magnets

Mechanical Design, Assembly and Strain Measurement Results of a 13-T Superconducting Dipole Magnet

Conceptual Design of a HTS CICC Coil for Fusion Devices based on Bi-2223 Tapes

Manufacturing and Testing of W/Cu Mono-Block Small Scale Mock-Up for EAST by HIP and HRP Technologies

Approaching ITER PF Coil Manufacturing

Recent EAST Experimental Results and Systems Upgrade in Support of Long-Pulse Steady-State Plasma Operation

Correction coil and magnet feeder lessons learned

Structural Design of DC Magnet for Super-X Test Facility