Abstract:A new lower tungsten divertor has been developed and installed in the EAST superconducting tokamak to replace the previous graphite divertor with power handling capability increasing from <2 MW m−2 to ∼10 MW m−2, aiming at achieving long-pulse H-mode operations in a full metal wall environment with the steady-state divertor heat flux of ∼10 MW m−2. A new divertor concept, ‘corner slot’ (CS) divertor, has been employed. By using the ‘corner effect’, a strongly dissipative divertor with the local buildup of high neutral pressure near the corner can be achieved, so that stable detachment can be maintained across the entire outer target plate with a relatively lower impurity seeding rate, at a separatrix density compatible with advanced steady-state core scenarios. These are essential for achieving efficient current drive with low-hybrid waves, a low core impurity concentration and thus a low loop voltage for fully non-inductive long-pulse operations. Compared with the highly closed small-angle-slot divertor in DIII-D, the new divertor in EAST exhibits the following merits: (1) a much simpler geometry with integral cassette body structure, combining vertical and horizontal target plates, which are more suitable for actively water-cooled W/Cu plasma facing components, facilitating installation precision control for minimizing surface misalignment, achieving high engineering reliability and lowering the capital cost as well; (2) it has much greater flexibility in magnetic configurations, allowing for the position of the outer strike point on either vertical or horizontal target plates to accommodate a relatively wide triangularity range, δ l = 0.4–0.6, thus enabling to explore various advanced scenarios. A water-cooled copper in-vessel coil has been installed under the dome. Five supersonic molecular beam injection systems have been mounted in the divertor to achieve faster and more precise feedback control of the gas injection rate. Furthermore, this new divertor allows for double null divertor operation and slowly sweeping the outer strike point across the horizontal and vertical target plates to spread the heat flux for long-pulse operations. Preliminary experimental results demonstrate the ‘corner effect’ and are in good agreement with simulations using SOLPS-ITER code including drifts. The EAST new divertor provides a test-bed for the closed divertor concept to achieve steady-state detachment operation at high power. Next step, a more closed divertor, ‘sharp-cornered slot’ divertor, building upon the current CS divertor concept, has been proposed as a candidate for the EAST upper divertor upgrade.

Fully Active Cooled In-vessel Components of EAST Tokamak

Power Balance Investigation in Long-Pulse High-Performance Discharges with ITER-like Tungsten Divertor on EAST

Physics Design of New Lower Tungsten Divertor for Long-Pulse High-Power Operations in EAST

Advances in the Long-Pulse Steady-State High Beta H-mode Scenario with Active Controls of Divertor Heat and Particle Fluxes in EAST

Divertor Power Deposition Control and ELM Mitigation with Supersonic Molecular Beam Injection in the EAST Tokamak

Operational Region and Sawteeth Oscillation in the East Tokamak

Recent EAST Experimental Results and Systems Upgrade in Support of Long-Pulse Steady-State Plasma Operation

Design and Test Results for the Pf Power Supply System of East

ECW assisted plasma startup with low toroidal electric field and full metal wall in EAST superconducting tokamak

Power Supply System of EAST Superconducting Tokamak

Overview of recent experimental results on the EAST tokamak

Preliminary Design of Water-Cooling System for Liquid Metal Divertor Target Test Module in EAST

Design and Platform Testing of the Compact Torus Central Fueling Device for the EAST Tokamak

Experimental research of ECW pre-ionization and assisted startup in EAST

EAST Ion Cyclotron Resonance Heating System for Long Pulse Operation

Development and Preliminary Commissioning Results of a Long Pulse 140 GHz ECRH System on EAST Tokamak (Invited)

Overview of R&D on Plasma-Facing Materials and Components in China

Realization of thousand-second improved confinement plasma with Super I-mode in Tokamak EAST

Characteristics of Edge-Localized Modes in the Experimental Advanced Superconducting Tokamak (East)

Development of a compact torus injector system for central fuelling technology of EAST

Design and analysis of actively-cooled, edge-transport diagnostic for long-pulsed operation in WEST