Abstract:A new lower tungsten divertor has been developed and installed in the EAST superconducting tokamak to replace the previous graphite divertor with power handling capability increasing from <2 MW m−2 to ∼10 MW m−2, aiming at achieving long-pulse H-mode operations in a full metal wall environment with the steady-state divertor heat flux of ∼10 MW m−2. A new divertor concept, ‘corner slot’ (CS) divertor, has been employed. By using the ‘corner effect’, a strongly dissipative divertor with the local buildup of high neutral pressure near the corner can be achieved, so that stable detachment can be maintained across the entire outer target plate with a relatively lower impurity seeding rate, at a separatrix density compatible with advanced steady-state core scenarios. These are essential for achieving efficient current drive with low-hybrid waves, a low core impurity concentration and thus a low loop voltage for fully non-inductive long-pulse operations. Compared with the highly closed small-angle-slot divertor in DIII-D, the new divertor in EAST exhibits the following merits: (1) a much simpler geometry with integral cassette body structure, combining vertical and horizontal target plates, which are more suitable for actively water-cooled W/Cu plasma facing components, facilitating installation precision control for minimizing surface misalignment, achieving high engineering reliability and lowering the capital cost as well; (2) it has much greater flexibility in magnetic configurations, allowing for the position of the outer strike point on either vertical or horizontal target plates to accommodate a relatively wide triangularity range, δ l = 0.4–0.6, thus enabling to explore various advanced scenarios. A water-cooled copper in-vessel coil has been installed under the dome. Five supersonic molecular beam injection systems have been mounted in the divertor to achieve faster and more precise feedback control of the gas injection rate. Furthermore, this new divertor allows for double null divertor operation and slowly sweeping the outer strike point across the horizontal and vertical target plates to spread the heat flux for long-pulse operations. Preliminary experimental results demonstrate the ‘corner effect’ and are in good agreement with simulations using SOLPS-ITER code including drifts. The EAST new divertor provides a test-bed for the closed divertor concept to achieve steady-state detachment operation at high power. Next step, a more closed divertor, ‘sharp-cornered slot’ divertor, building upon the current CS divertor concept, has been proposed as a candidate for the EAST upper divertor upgrade.

Design and analysis of actively-cooled, edge-transport diagnostic for long-pulsed operation in WEST

Toward a First-Principles Integrated Simulation of Tokamak Edge Plasmas

Multichannel gas electron multiplier based soft x-ray field-programmable gate array measurement system for W-Environment in Steady-state Tokamak (WEST): Hardware, installation, and first plasma acquisition

Fully Active Cooled In-vessel Components of EAST Tokamak

Wall conditions in WEST during operations with a new ITER grade, actively cooled divertor

Real-Time Detection of Overloads on the Plasma-Facing Components of Wendelstein 7-X

Development of a thermal diagnostic system for the SPARC tokamak

Power Balance Investigation in Long-Pulse High-Performance Discharges with ITER-like Tungsten Divertor on EAST

WEST full tungsten operation with an ITER grade divertor

Global analysis of tungsten migration in WEST discharges using numerical modelling

Physics Design of New Lower Tungsten Divertor for Long-Pulse High-Power Operations in EAST

Development and Optimization of Step-A Linear Plasma Device for Plasma-Material Interaction Studies

A step towards the diagnostic of the ITER first wall: in-situ LIBS measurements in the WEST tokamak

Preliminary Design of Water-Cooling System for Liquid Metal Divertor Target Test Module in EAST

Determination of the mean energy of fast electron losses and anisotropies through thick-target emission on WEST

Heterogeneous Online Computational Platform for GEM-Based Plasma Impurity Monitoring Systems

Recent Studies of Tungsten-Based Plasma-Facing Materials in the Linear Plasma Device STEP

Evolution of pre-damaged ITER grade plasma facing components under WEST plasma exposure: smoothing and tungsten sources

Survey of tungsten gross erosion from main plasma facing components in WEST during a L-mode high fluence campaign

Development of advanced high heat flux and plasma-facing materials

Overview of R&D on Plasma-Facing Materials and Components in China