Abstract:The acidic (pKa ≈1.5–2.5) and hygroscopic nature of poly(3,4-ethylene dioxythiophene) polystyrene sulfonate, used as a common hole-injection layer in optoelectronic devices, has a detrimental effect on device stability and is associated with well established device failure mechanisms. In this work, a process with a high green index hole-injection layer material (V2O5) and low surface roughness (RMS roughness ≈1.3 nm) was developed for demonstrating a hybrid polymer–inorganic perovskite light-emitting diode. Test devices with the new hole-injection layer demonstrate nearly identical maximum current efficiencies (4.23 vs 4.19 cd/A), and luminous efficacies (2.99 vs 2.32 lm/W) when compared to a control device fabricated with the conventional hole-injection layer. Furthermore, the peak brightness was achieved at a current density one-third of the value for the control device. To examine the transport of holes in the above hole-injection layer, we carried out device simulations based on a physical charge control model, including defect-assisted tunneling for hole injection. Close agreement for current–voltage characteristics is observed. Experimentally measured mobility in the device and measured radiative lifetimes were found to be sufficient to achieve this agreement without resorting to the introduction of a sheet charge at the injection interface. Despite the use of a bulk-heterojunction device architecture, the model predicts high radiative recombination rates [≈5.6×1022/(cm3s)] in the emissive layer, consistent with the measured photophysical properties for the active film, suggesting effective passivation of non-radiative surface states.

Dual Role of Lif As A Hole-Injection Buffer in Organic Light-Emitting Diodes

Modeling and Numerical Study of Electrical Characteristics of Polymer Light-Emitting Diodes Containing an Insulating Buffer Layer

Enhanced Hole Injection in Organic Light-Emitting Devices by Using Fe3O4 As an Anodic Buffer Layer

Role of Hole Playing in Improving Performance of Organic Light-Emitting Devices with an Al2o3 Layer Inserted at the Cathode-Organic Interface

Enhancement of Electron Injection in Organic Light-Emitting Devices Using an Ag/LiF Cathode

Electron Blocking and Hole Injection: the Role of N,N′-Bis(naphthalen-1-y)-N,N′-bis(phenyl)benzidine in Organic Light-Emitting Devices

Buffer-enhanced Electron Injection in Organic Light-Emitting Devices with Copper Cathode

LiF layer at the interface of Au cathode in organic light-emitting devices: A nonchemical induced carrier injection enhancement

Effects of charge injection barrier on the dark current of organic photodiodes

Enhanced Hole Injection in a Bilayer Vacuum-Deposited Organic Light-Emitting Device Using a P-Type Doped Silicon Anode

Mechanisms of Injection Enhancement in Organic Light-Emitting Diodes Through Insulating Buffer

Buffer-Layer-Induced Barrier Reduction: Role of Tunneling in Organic Light-Emitting Devices

Modification of the Hole Injection Barrier in Organic Light-Emitting Devices Studied by Ultraviolet Photoelectron Spectroscopy

Obvious Efficiency Enhancement of Organic Light-Emitting Diodes by Parylene-N Buffer Layer

Revealing the influence of hole injection material's molecular orientation on OLED's performance

Hole injection control of electron blocking layer for broad recombination zone and low-efficiency roll-off in phosphorescent organic light emitting device

Improving Electron Injection of Organic Light-Emitting Transistors via Interface Layer Design

Design of Hole Blocking Layer with Electron Transport Channels for High Performance Polymer Light‐Emitting Diodes

Interfacial Coulomb-enhanced charge injection for efficient perovskite light-emitting diodes

Improving Performance Of Deep-Blue Oled By Inserting Ultra-Thin Lif Between Hole-Blocking And Electron-Transporting Layers

Defect-assisted hole transport through transition metal oxide-based injection layers for passivated nanocrystalline CsPbBr3 emissive thin films: A combined experimental and modeling study