Abstract:Bulk nanostructured (grain sizes in the range of 50-200nm) and ultrafine structured (grain sizes in the range of 100-500nm) gamma-TiAl based alloys with compositions Ti-47Al (in at%) and Ti-45Al-2Cr-2Nb-1B-0.5Ta (in at%), respectively, have been produced using a combination of high energy mechanical milling of mixtures of elemental powders and hot isostatic pressing at 800 and 1000 degrees C respectively, and the microstructures of the samples have been characterised. At room temperature, the HIPed samples fractured prematurely at tensile stresses in the range of 200-300MPa and showed no ductility, very likely due to the relative high oxygen content (0.6wt%) in the samples and very low tolerance of TiAl based alloys on dissolved oxygen. At 800 degrees C, the HIPed samples showed a yield strength in the range of 55-70MPa, a tensile strength in the range of 60-80MPa, a large amount of elongation to fracturing around 100% and clear strain softening. Examination of the fractured tensile test specimens at room temperature and 800 degrees C showed that the level of the consolidation was fairly high, but the HIPed samples do contain a small fraction of interparticle boundaries with weak atomic bonding. The fracture of the HIPed samples in tensile testing at room temperature and 800 degrees C, respectively, is predominately intergranular, and the large amount of plastic deformation prior to fracture at 800 degrees C is achieved mainly through grain boundary sliding in conjunction with dislocation gliding, in agreement with the deformation mechanisms of nanostructured and ultrafine structured alloys generally agreed by researchers.

Mechanical synthesized nanocrystalline Ti/Al composite powders as precursor for Ti/Al alloy via reactive sintering

In Situal3ti–al2o3 Intermetallic Matrix Composite: Synthesis, Microstructure, and Compressive Behavior

Preparation of Ti/Al based nanophase composite powder by mechanical alloying

Mechanical Alloying and Spark Plasma Sintering of Ni-Al-Ti-B Powders for Fabricating Nanocrystailine (Tib+tib2)/ni-3(Al, Ti) Composite

Preparation of ti-al based nanophase composite powder by mechanical alloying

Synthesis of Tial Based Alloy by Mechanical Milling, Warm Pressing and Reactive Sintering

Consolidation of Nanocrystalline Al-Ti Alloy Powders Synthesized by Mechanical Alloying

Synthesis of Fine Grain Ti3sic2 by Spark Plasma Sintering with Additive of Aluminum

Microstructure and Properties of A Tial Alloy Prepared by Mechanical Milling and Subsequent Reactive Sintering

Mechanical properties and fracture behaviour of nanostructured and ultrafine structured TiAl alloys synthesised by mechanical milling of powders and hot isostatic pressing

In Situ Synthesis of Ti2AlC–Al2O3/TiAl Composite by Vacuum Sintering Mechanically Alloyed TiAl Powder Coated with CNTs

The sintering densification, microstructure and mechanical properties of Ti–48Al–2Cr–2Nb by a small addition of Sn–Al powder

Reactive Synthesis of Polycrystalline Ti3AlC2 and Its Sintering Behavior

Synthesis Of High-Purity Powder Ti3alc2 Materials By Pressureless Sintering

Preparation of fine-grains TiAl alloys by mechanical alloying and spark plasma sintering

Fabrication of high purity Ti3SiC2 from Ti/Si/C with the aids of Al by spark plasma sintering

Preparation of TiAl-based alloys by mechanical milling and reactive sintering

Synthesis and Properties of an Ultrafine Grained Ti-45al-2cr-2nb-1b-0.5ta Alloy Prepared by Double Mechanical Milling and Spark Plasma Sintering

Preparation and Characterization of TiB2/Al3Ti/Al2O3 Composite Nano-powder

Effect of Aluminum on Fabrication of Ti3SiC2 by Mechanical Alloying and Spark Plasma Sintering