Abstract:In order to investigate the influence of gradual stress relieving treatment on the microstructure, texture evolution, grain structure, and misorientation distribution of the hot-rolled Ti6Al4V-5Cu (alpha+(3) alloy deformed in various thickness reduction ratios (TRR's) of 15%, 58%, and 73% to maintain the burger orientation relationship (BOR), different stress reliving treatment was specially designed for relieving the residual stresses occurred due to the hot deformation process. Using IPF maps, the majority of the alpha grains, specifically the elongated ones were found nearly at 45 degrees with respect to the rolling and transverse direction. The study also show that the heat treatment schedule on the 58% deformed alloy significantly promote the transformation of (3 to alpha phase and a special microstructure with an equiaxed grains is produced. The local misorientation angle distribution due to stress reliving treatment has also discussed. Using EBSD analysis, the alloy processed under highest TRR's (i.e., 73%) and subsequent stress relieving treatment could result a serious internal crystalline instability with various degree of element diffusion rate, which promote a severe and ease of alloy coarsening. Thus, coarsening encourage the formation of grains with the highest softening potential, comparatively. It is obvious that the stress-relived treatment does not result a change in microstructure. However the internal residual stresses on the hot deformation were relieved, the texture intensity had increased quietly. A significant textural behavior could be achieved on the 73% hot-rolled alloys by the stress-relieving process to align the alpha/(3 fiber texture interface in parallel coincidence to maintain the BOR.

Effect of Triple Annealing Treatment on Stress Relaxation of Ti-6Al-4V Alloy

Effect of Triple Annealing Treatment on Stress Relaxation of Ti-6A1-4V Alloy

Stress Relaxation Behavior and Related Mechanism of Ti-6al-4v Alloy with Widmanstatten Microstructure

Stress Relaxation Behavior of Ti-6Al-4V Alloy

Research on stress relaxation behavior of TA15 titanium alloy

A Unified Constitutive Model of Stress Relaxation of Ti-6Al-4V Alloy with Different Temperatures from Elastic to Plastic Loading

Effects of Microstructure on Stress Relaxation Behaviors of Alloy BT14

Relation Between Short-term Creep and Stress Relaxation of Titanium Alloy at High Temperature

Effects of Triple Heat Treatment on Stress Relaxation Resistance of Bt20 Alloy

Effect of Thermal Annealing on the Microstructure, Mechanical Properties and Residual Stress Relaxation of Pure Titanium after Deep Rolling Treatment

Investigation on High Temperature Short-Term Creep and Stress Relaxation of Titanium Alloy

The Effect of Annealing and Cryogenic Treatment on the Microstructure and Mechanical Properties of Ti-6Al-4V Alloy

Accelerated stress relaxation with simultaneously enhanced strength of titanium alloy by phase transformation and stress-induced twinning

Atomic Simulation of Effect of Stress-Relief Annealing on the Regulation of Residual Stress in Nano-cutting of γ-TiAl Alloy

Influence of Gradual Stress Relieving on the Microstructure, Texture Development, Grain Structure and Orientation of the Hot-Rolled Ti6Al4V-5Cu Alloy.

Effects of Annealing on the Residual Stress in γ-TiAl Alloy by Molecular Dynamics Simulation

Relaxation mechanisms of near – α titanium alloy during stress relaxation with synchronous aging

Experimental and Modeling Studies on the Stress Relaxation Behaviour of Ti-6Al-4V Alloy

Study on the Stress Relaxation with Synchronous Ageing of Near Α Titanium Alloy

Effect of Annealing Temperature on the Strength and Toughness of Ti‐55531 Titanium Alloy After Multiple Heat Treatment

Effect of Repetitive Bending and Straightening Process on Microstructure Properties and Deformation Mechanism of A Ti–Al–Cr–Mo Alloy