Abstract:The effect of major constituents (the Li content increases from 0.5 to 3 wt% and the Cu content decreases from 4.5 to 2 wt%) on microstructure and mechanical properties of cast Al-Li-Cu-Zr alloy were studied to understand a qualitative assessment of sequence and kinetics of multiple precipitations. Increasing the Li content progressively raises the melting temperature from 520 °C in 1# alloy (Al-0.5Li-4.5Cu, wt%) and 2# alloy (Al-1Li-4.5Cu) to 560 °C in 6# alloy (Al-3Li-2Cu). In addition, the variations of the major constituents result in the changes of the type and volume fraction of the inter- and intra-granular intermetallic phases. TEM results indicate that minor modifications to alloy composition greatly alter precipitation behavior during isothermal aging. The Li-poor alloy (2# alloy) presents a much shorter incubation time of T1-Al2CuLi precipitate than the Li-rich alloy (Al-1.5Li-4.5Cu, 3# alloy), while the nucleation of θ'-Al2Cu precipitate is promoted in Li-rich alloy. No typical spherical δ'-Al3Li precipitate is observed in 2# and 3# alloys during isothermal aging, except for the as-quenched 3# alloy. The preferential nucleation of δ' precipitate on the coherent and broad face of θ' precipitate is observed in 2# and 3# alloys, leading to the formation of "sandwich-like" δ'/θ'/δ' phases. Further decreasing Cu content to 2 wt% and increasing Li content to 3 wt% (6# alloy), the predominant phase in the matrix is δ' precipitate, accompanied by a small amount of unevenly distributed θ' and T1 precipitates. The best balance between ductility and strength is obtained by 2# alloy aged for 32 h, but 6# alloy has significant advantages in terms of density (2.437 g/cm3) and elastic modulus (82.65 GPa) over 2# alloy (density: 2.675 g/cm3; elastic modulus: 75.45 GPa).

Effect of Small Content Cu on Microstructure and Properties of Spray Deposited Al-Li Alloy

The Effect of Al on Microstructure and Properties of Cu-15Ni-8Sn During the Aging

On the microstructure and tensile properties of rapidly solidified Al-Li alloy by spray deposition processing

Microstructure and tensile properties of rapidly solidified Al-3.8Li-0.8Mg-0.4Cu-0.13Zr alloy prepared by spray deposition

Effect of Li on Microstructures and Properties of Al-3.5Cu-1.5Mg Alloy

Effects of Mg and Cu on Microstructures and Properties of Spray-Deposited Al-Zn-Mg-Cu Alloys

The effect of major constituents on microstructure and mechanical properties of cast Al-Li-Cu-Zr alloy

Age precipitation phase in rapidly solidified Al-Li alloy made by spray deposition process

Effects of Li content on microstructure evolution and mechanical properties of squeeze-cast Al-5Cu- x Li alloy assisted with ultrasonic treatment

Influence of Li addition on mechanical property and aging precipitation behavior of Al-3.5Cu-1.5Mg alloy

Role of Cu on the Mechanical Properties and Microstructures Evolution of Al-xCu-1Li-0.4Mg–1Zn-0.1Zr Alloys

The influence of Cu/Li ratio on precipitation in Al–Cu–Li–x alloys

Effect of Cu Content on Microstructure and Mechanical Properties of Al-Cn-0.4Mg-0.6Ag Alloy

Effect of Ti content on microstructures and mechanical properties of cast Al-2Li-2Cu-0.5Mg alloy

Precipitate microstructures, mechanical properties and corrosion resistance of Al-1.0 wt%Cu-2.5 wt%Li alloys with different micro-alloyed elements addition

Microstructural Evolution of Al-Cu-Li Alloys with Different Li Contents by Coupling of Near-Rapid Solidification and Two-Stage Homogenization Treatment

Effect of Li Content on Properties and Microstructure Evolution of Near-Rapid Solidified 2A97 Al-Li Alloy

Microstructure, Mechanical Properties, and Corrosion Behavior of Al-4.0Cu-1.1Li-0.5Mg-xAg Alloys

Microstructural characteristics and mechanical properties of cast Al-3Li-xCu-0.2Zr alloy

Effect of Li Content on Microstructure and Mechanical Property of Mg−xLi−3(Al−Si) Alloys

Microstructure and Mechanical Properties of Cast Al-Li-Mg Alloy: Role of Cu Addition and Heat Treatment