High-channel-count comb filter with a simple structure

Xiangfei Chen,Jin Mao,Xuhui Li,Zhongqiang Lin,Shizhong Xie,Chongcheng Fan

2004-01-01

Abstract:Based on the analysis of comb filter formed by highly chirped sampled Bragg grating, a 36-channel comb filter is fabricated with 28 nm bandwidth, 0.31 nm channel bandwidth (0.5 dB), >22 dB adjacent channel isolation and <0.4 dB insertion loss.

What problem does this paper attempt to address?

High Channel-Count Comb Filter Based on Chirped Sampled Fiber Bragg Grating and Phase Shift

YT Dai,XF Chen,XM Xu,CC Fan,SZ Xie

DOI: https://doi.org/10.1109/lpt.2005.846760

IF: 2.6

2005-01-01

IEEE Photonics Technology Letters

Abstract:Based on strongly chirped sampled fiber Bragg grating and phase shifts, a novel approach to obtain high channel-count comb filters is proposed in this letter. Various channel spacing can be achieved by a single strongly chirped phase mask where the required phase shifts can be gained by a precise translation stage. Comb filters with channel spacing of 50, 100, and 200 GHz are then designed with the same phase mask. Experimentally, a 35-channel 100-GHz channel-spacing comb filter is fabricated, from which one can expect that high-performance comb filter with various channel spacing can be fabricated by conventional technology.
Narrow-Band Add-Drop Filter Based on Cladding-Modulated Apodized Multimode Bragg Grating

Huiye Qiu,Lisheng Lin,Ping Yu,Tingge Dai,Xiaoqing Jiang,Hui Yu

DOI: https://doi.org/10.1109/jlt.2019.2937412

IF: 4.7

2019-01-01

Journal of Lightwave Technology

Abstract:A narrow-band add-drop filter based on an anti-symmetric cladding-modulated multimode Bragg grating (CMMBG) is demonstrated on the silicon-on-insulator (SOI) platform. The CMMBG is implemented by using periodic placements of silicon cubes along a multimode waveguide. The coupling strength is varied by changing the distance between the cubes and the multimode waveguide. An unlimited free-spectral range (FSR) and weak coupling strengths for TE0-TE1 modes conversion are achieved. Sidewall-misalignment-modulation (SMM) apodization is applied to achieve a high sidelobe suppression ratio (SLSR). The experimental results show that the designed filtering device has a 3-dB bandwidth of 0.8 nm, an insertion loss of 0.65 dB and a SLSR of 20.3 dB. The devices with different grating duty cycles and multimode waveguide widths were also fabricated and analyzed. Our devices are promising for on-chip applications that require narrow bandwidths such as WDM channel filters.
Design of an on-chip integrated multi-channel comb filter based on the Bragg grating structure

Hualin Pu,Jia Ye,Zongxin Gan,Lianshan Yan,Xihua Zou,Wei Pan

DOI: https://doi.org/10.1364/ol.533843

IF: 3.6

2024-09-05

Optics Letters

Abstract:Hualin Pu, Jia Ye, Zongxin Gan, Lianshan Yan, Xihua Zou, Wei Pan We designed a multi-channel comb filter generation scheme with nearly consistent channel numbers and free spectral range (FSR) in standard ... [Opt. Lett. 49, 5063-5066 (2024)]

optics
Selectable-FSR 10-Ghz Granularity WDM Superchannel Filter in a Reconfigurable Photonic Integrated Circuit

Yiwei Xie,Zihan Geng,Deming Kong,Leimeng Zhuang,Arthur J. Lowery

DOI: https://doi.org/10.1109/jlt.2018.2819687

IF: 4.7

2018-01-01

Journal of Lightwave Technology

Abstract:We present a 10-GHz granularity reconfigurable WDM superchannel filter in a photonic integrated circuit. The filter uses a ring-resonator-assisted tapped-delay-line topology. An example configuration with two ring resonators and four tapped delay lines provides a spectral filter with a flat-top passband, a roll-off factor of 8%, a tunable central wavelength, and a selectable free spectral range, i.e., 2x or 4x the 3-dB passband bandwidth. The device was fabricated in a silicon nitride (Si3N4/SiO2) waveguide with a chip area of 0.36 cm(2) and has a fiber-to-fiber insertion loss of 5 dB. We experimentally demonstrate the filter for selecting a subchannel from a WDM superchannel comprising 10-GHz sub-channels with 10% and zero guard bands. Owing to the infinite impulse responses of ring resonators, this filter requires a significantly smaller area and fewer tuning elements compared with designs based on only tapped-delay-line finite-impulse-response filters. This paper contributes to the creation of chip-scale all-optical WDM superchannel transceivers and reconfigurable optical add/drop multiplexers (ROADMs).
High Extinction Ratio On-Chip Pump-Rejection Filter Based on Cascaded Grating-Assisted Contra-Directional Couplers in Silicon Nitride Rib Waveguides

Xiaomin Nie,Nina Turk,Yang Li,Zuyang Liu,Roel Baets

DOI: https://doi.org/10.1364/ol.44.002310

IF: 3.6

2019-01-01

Optics Letters

Abstract:We present an on-chip filter that is based on the grating-assisted contra-directional coupler (GACDC) implemented on a silicon nitride rib waveguide platform. This filter enjoys the benefit of an unlimited free spectral range (FSR) on the red side of the stop/passband. Unlike a Bragg reflector, the GACDC filter has the advantage of coupling the rejected light contra-directionally into a bus waveguide, instead of reflecting it back to the input. This property makes it an add/drop filter suitable for pump rejection and allows effective cascading to provide an even higher extinction ratio compared to the single-stage version. In this Letter, we experimentally demonstrate that a 16-stage cascaded GACDC filter can provide a stop band with a bandwidth smaller than 3 nm and an extinction ratio as high as 68.5 dB.
Ultra-Broadband Optical Filter Based on Step-Chirped Multimode Waveguide Bragg Grating

Nannan Ning,Qiang Zhang,Zhujun Wei,Qikai Huang,Penghui Xia,Yuehai Wang,Jianyi Yang,Hui Yu

DOI: https://doi.org/10.1109/jphot.2023.3297108

IF: 2.4

2023-01-01

IEEE Photonics Journal

Abstract:An ultra-broadband optical filter based on step-chirped multimode waveguide Bragg grating (SCMWBG) with low insertion loss, high sidelobe suppression ratio (SLSR), compact size and relaxed fabrication accuracy is demonstrated on SOI platform. The grating length of SCMWBG is divided into grating segments with constant periods, and the period of each segment increases in a fixed step length of 1 nm. Each grating segment of the proposed SCMWBG is designed according to the phase-matching condition. The device is fabricated by a 193 nm DUV lithography, and employs complementary lateral-misalignment apodization to suppress the sidelobes. The measured insertion loss, SLSR and 3-dB bandwidth of fabricated SCMWBG are 1.2 dB, 17 dB and 72 nm, respectively.
Narrow-Band Add-Drop Filter Based on Phase-Modulated Grating-Assisted Contra-Directional Couplers

Huiye Qiu,Jianfei Jiang,Ping Yu,Debin Mu,Jianyi Yang,Xiaoqing Jiang,Hui Yu,Rui Cheng,Lukas Chrostowski

DOI: https://doi.org/10.1109/jlt.2018.2852483

IF: 4.7

2018-01-01

Journal of Lightwave Technology

Abstract:A narrow-hand silicon photonic add-drop filter is demonstrated by using phase-modulated grating-assisted contra-directional couplers (contra-DCs) on the silicon-on-insulator platform. The apodization coupling is achieved by modulating the phase of one grating in a contra-DC, while keeping the other grating uniform. As the local effective index of the gratings remains almost unchanged, the designed apodized contra-DC has a large designing flexibility and a high sidelobe suppression ratio (SLSR). To obtain a narrow bandwidth, weak coupling is designed. Single-stage and dual-stage filtering are both studied. The experimental results show that single-stage filtering device has a 3-dB bandwidth of 0.9 nm and an SLSR of 18 dB. Dual-stage filtering device has a 3-dB bandwidth of 0.5 nm and an SLSR of 23 dB. Our devices are promising for on-chip applications that require narrow bandwidths such as wavelength-division-multiplexed channel filters.
Fibre-optic Comb Filter with Tunable Central Wavelength and Channel Isolation at Sub-Microsecond Speed

F. Zhang,X. F. Jin,X. M. Zhang,S. L. Zheng,H. Chi,K. Y. Zou,J. P. Yao

DOI: https://doi.org/10.1049/el.2010.2379

2010-01-01

Electronics Letters

Abstract:Reported is a novel and compact tunable fibre-optic comb filter with the tuning implemented based on two electro-optic phase retarders made of lead magnesium niobate-lead titanate. Both the central wavelength and the channel isolation can be tuned at a sub-microsecond speed. A prototype filter with insertion loss of around -1.3 dB and channel isolation up to 26 dB is achieved.
High-efficiency Wideband SiNx-on-SOI Grating Coupler with Low Fabrication Complexity.

Pengfei Xu,Yanfeng Zhang,Zengkai Shao,Lin Liu,Lidan Zhou,Chunchuan Yang,Yujie Chen,Siyuan Yu

DOI: https://doi.org/10.1364/ol.42.003391

IF: 3.6

2017-01-01

Optics Letters

Abstract:The chip-fiber grating coupler is a fundamental building block in integrated photonics, providing convenient on-wafer testing and packaging. Couplers based on a silicon nitride (SiNx) material platform can achieve wider bandwidths than silicon-based couplers, but suffer from lower efficiency due to the relative low material refractive index. The efficiency of the SiNx grating coupler can be improved by using high-reflectivity silicon grating reflectors underneath. However, such a silicon grating reflector requires several fabrication steps, including lithography, etching, high precision alignment (HPA), and chemical mechanical polishing (CMP). In this Letter, we demonstrate an easy-to-fabricate SiNx-on-SOI transverse-electric mode grating coupler requiring only one patterning step (grating alone), and without the need for HPA and CMP. A coupling coefficient of -2.5 dB and 1-dB-bandwidth of 65 nm has been experimentally measured.
High-efficiency Grating Coupler Based on Fast Directional Optimization and Robust Layout Strategy in 130 Nm CMOS Process.

Xiangyu Luo,Guangcan Mi,Yanbo Li,Tao Chu

DOI: https://doi.org/10.1364/ol.452054

IF: 3.6

2022-01-01

Optics Letters

Abstract:We experimentally demonstrated a high-efficiency grating coupler by combining an interleaved etch and apodized structure for fiber-to-chip coupling. The grating coupler was optimized using the fast directional optimization method to achieve apodization. The grating coupler utilized a layout strategy involving an extended mask to avoid alignment errors for a multi-etch structure. The coupling efficiency was measured to be -2.2 dB at a wavelength of 1549 nm with a 3 dB bandwidth of 47 nm. The grating coupler, having no gold reflector, subwavelength index matching structure, or additional material layers, was fabricated using a commercial silicon photonics process with a minimum feature size of 140 nm. This grating coupler design provides a robust and effective coupling scheme and the proposed method can be employed to adopt the design in accordance with standard foundry design rules.
Inverse Design of the Multimode Bragg Grating Based on Time-Domain Layer Peeling Method

Xiaofei Wang,Hui Yu,Nannan Ning,Qikai Huang,Yuehai Wang,Xiaoqing Jiang,Jianyi Yang

DOI: https://doi.org/10.1117/12.2644810

2022-01-01

Abstract:Multimode waveguide Bragg gratings filters with square shape amplitude responses and well-controlled dispersion characteristics are achieved by the Time-Domain Layer Peeling method for the first time, the Bragg grating structures can be mapped by the complementary lateral-misalignment modulation apodization. Three filters with different amplitude and phase responses are demonstrated. For the dispersion-less filter, the dispersion compensation filter and the three-channel dispersionless filter, the 3 dB bandwidth and the group delay of the realizable spectral responses are 4.0 nm, 4.7 nm, 2.1 nm and 0 ps/nm, 5.7 ps/nm, 0 ps/nm, the group delay ripples have a standard deviation of 1.7 ps, 1.5 ps, and 2.0 ps. The multimode relaxes the fabrication requirement in terms of both the lithography resolution and minimum feature size/spacing while maintaining the advantages of low insertion loss.
A reconfigurable photonic microwave channelized receiver based on an optical comb

Ze Li,Hao Chi,Zhang, Xianmin,Shilie Zheng

DOI: https://doi.org/10.1109/MWP.2011.6088729

2011-01-01

Abstract:A photonic approach to implementing microwave channelized receiver based on an optical comb is proposed. In this approach, a flat optical comb with 11 comb lines is generated using two cascaded Mach-Zehnder modulators (MZMs). Frequency analysis of an intercepted microwave signal with multiple microwave frequencies is realized by using the optical comb together with a Fabry-Perot (F-P) etalon, a wavelength division multiplexer (WDM) and a photodetector array. A simulation is performed. A tunable operating bandwidth of 11 or 16.5 GHz with a tunable accuracy of ±0.5 or ±0.75 GHz is obtained.
Birefringence compensated arrayed waveguide grating

jun zou,xiang xia,tingting lang,jianjun he

DOI: https://doi.org/10.1117/12.2071941

2014-01-01

Abstract:In this paper we review our work on birefringence compensated arrayed waveguide grating. We elaborate on a birefringence compensation technique based on angled star couplers in arrayed waveguide grating (AWG) and discuss several demonstrations both in low-index-contrast and high-index-contrast material systems. A 16-channel AWG with 100GHz channel spacing for DWDM application is designed and fabricated in silica-based low-index-contrast waveguide. The experimental results confirm that the polarization-dependent wavelength shift (PD lambda) can be tuned by varying the incident/diffraction angle at the star couplers and a birefringence-free property can be achieved without additional fabrication process as compared to conventional AWG. A further validation of this technique is demonstrated in high-index-contrast silicon-on-insulator waveguide, in combination with different diffraction orders for TE and TM polarizations. A birefringence compensated silicon nanowire AWG for CWDM optical interconnects is designed and fabricated. The theoretical and experimental results show that the PD lambda can be reduced from 380-420nm to 0.5-3.5 nm, below 25% of the 3 dB bandwidth of the channel response in the wavelength range of 1500 to 1600nm.
Silicon Band-Rejection and Band-Pass Filter Based on Asymmetric Bragg Sidewall Gratings in A Multimode Waveguide

Huiye Qiu,Jianfei Jiang,Ping Yu,Tingge Dai,Jianyi Yang,Hui Yu,Xiaoqing Jiang

DOI: https://doi.org/10.1364/ol.41.002450

2016-01-01

Abstract:A silicon photonic wire filter based on an asymmetric side-wall Bragg grating in a multimode silicon-on-insulator strip waveguide is demonstrated. The operating principle is based on the contra-directional coupling between the transverse electric fundamental (TE0) and first-order (TE1) modes, which is enabled by the asymmetric spatially periodic refractive-index perturbations. An asymmetric Y-junction is cascaded at the input port of the filter so as to drop the Bragg reflection. Compared with conventional Bragg grating-based filters, this device eliminates the back reflection at the input port and the 6 dB inherent insertion loss at the drop port; moreover, a narrow 3 dB bandwidth can be obtained with a large critical dimension as a result of the weak coupling strength between the TE0 and TE1 modes inside the multimode waveguide. Experimental results show that a bandwidth of similar to 2.8 nm is achieved by a large corrugation width of 150 nm. The insertion loss at the drop port is -2.1 dB, and the extinction ratio is -33 dB at the through port. (C) 2016 Optical Society of America
Design and characterization of novel comb filters based on periodical fiber Bragg gratings

Dingli Zeng,Shizhong Xie,Chengcheng Sun,Weiming Mao,Bingkun Zhou

1997-01-01

Abstract:A new method for designing comb filters based on periodical fiber Bragg gratings is presented. The reflective response of periodical gratings is theoretically analyzed. The design principle is proposed. It is of interest to fabricate such comb filters for WDM/FDM applications and fiber lasers in terms of a uniform phase mask.
Design and fabrication of 1 × 32 silica-based arrayed waveguide grating

WenHua Long,GuangBo Li,Kemiao Jia,Hongchang Qu,Yanzhe Tang,Yaming Wu,Jianyi Yang,Yuelin Wang-

2005-01-01

Abstract:A 1 × 32 silica-on-silicon-based arrayed waveguide grating is designed and fabricated. The detailed consideration of waveguide bending, coupling between adjacent waveguides, and the taper structure for the design of the arrayed waveguide grating is presented. By applying the high-resolution photomask, PECVD-based silica deposition, reactive ion etching, and 8° end-face polishing, a AWG chip is obtained with crosstalk lower than -28 dB for the adjacent channels and -35 dB for the non-adjacent channels. The average insertion loss is about 4.9 dB and the imbalance is approximately 1.72 dB after the chip is fiber-array coupled and packaged.
In-line flat-top comb filter based on a cascaded all-solid photonic bandgap fiber intermodal interferometer.

Youfu Geng,Xuejin Li,Xiaoling Tan,Yuanlong Deng,Yongqin Yu

DOI: https://doi.org/10.1364/OE.21.017352

IF: 3.8

2013-01-01

Optics Express

Abstract:In this paper, an in-line comb filter with flat-top spectral response is proposed and constructed based on a cascaded all-solid photonic bandgap fiber modal interferometer. It consists of two short pieces of all-solid photonic bandgap fiber and two standard single-mode fibers as lead fibers with core-offset splices between them. The theoretical and experimental results demonstrated that by employing a cut and resplice process on the central position of all-solid photonic bandgap fiber, the interference spectra are well tailored and flat-top spectral profiles could be realized by the controllable offset amount of the resplice. The channel position also could be tuned by applying longitudinal torsion with up to 4 nm tuning range. Such a flat-top fiber comb filter is easy-to-fabricate and with a designable passband width and flat-top profile.
128 Channels of Integrated Filter Array Rapidly Fabricated by Using the Combinatorial Deposition Technique

S.-W. Wang,M. Li,C.-S. Xia,H.-Q. Wang,X.-S. Chen,W. Lu

DOI: https://doi.org/10.1007/s00340-007-2726-3

2007-01-01

Applied Physics B

Abstract:A combinatorial deposition technique is developed to fabricate integrated narrow bandpass filters (NBPFs) on a single substrate. It is highly efficient for the fabrication of integrated filter arrays in optical regions. An array integrated with 128 NBPFs has been fabricated by using the technique with only a nine-step deposition process. The pass-bands of the filters distribute almost linearly in the range of 722.0-880.0 nm. Their relative bandwidth is smaller than 0.44%.
Silica-Based Arrayed Waveguide Grating With Flattened Spectral Response Using A Multimode Interference Coupler

Yz Tang,Km Jia,By Li,Jy Yang,Xq Jiang,Ym Wu,Yl Wang

DOI: https://doi.org/10.1088/0256-307X/21/6/024

2004-01-01

Chinese Physics Letters

Abstract:We designed and fabricated an arrayed waveguide grating based on silica-on-silicon materials with flattened spectral response by adding a multimode interference coupler in the input region. The theoretical analysis and calculation are given. The device has worked effectively and has been tested with the passband 0.43 nm at 1 dB, 0.72 nm at 3 dB and 1.56 nm at 20 dB respectively, at a cost of power penalty of about 1.5 dB. The crosstalk is less than -30 dB, owing to the high-resolution photomask and well-controlled fabrication processes.
Integrated Broadband Filter with Sharp Transition Edges Based on SiN and SiON Composite Waveguide Coupler

Xiao Ma,Qiongchan Shao,Jiamei Gu,Tingting Lang,Xiang Guo,Jian-Jun He

DOI: https://doi.org/10.3390/photonics10111285

IF: 2.536

2023-01-01

Photonics

Abstract:Broadband filters with sharp transition edges are important elements in diverse applications, including Raman and fluorescence spectral analysis, wideband wavelength-division multiplexing (WDM), and multi-octave interferometry. While the multi-layer thin-film interference broadband filter has been widely applied in various free-space optical systems, its integrated counterpart is still far from mature, which is also highly desired for constructing chip-scale miniature optical modules. In this article, we design, fabricate, and characterize an integrated broadband filter with sharp transition edges. An adiabatic coupler based on silicon nitride (SiN) and silicon oxynitride (SiON) composite waveguide is employed here. Long-pass, short-pass, band-pass, and band-stop filters can be realized in a single design of the composite waveguide coupler for a specific wavelength range, with only a difference in the SiN taper waveguide width. Experimental results with a roll-off value of larger than 0.7 dB nm−1 and a 15 dB extinction ratio (ER) are presented.

High-channel-count comb filter with a simple structure

High Channel-Count Comb Filter Based on Chirped Sampled Fiber Bragg Grating and Phase Shift

Narrow-Band Add-Drop Filter Based on Cladding-Modulated Apodized Multimode Bragg Grating

Design of an on-chip integrated multi-channel comb filter based on the Bragg grating structure

Selectable-FSR 10-Ghz Granularity WDM Superchannel Filter in a Reconfigurable Photonic Integrated Circuit

High Extinction Ratio On-Chip Pump-Rejection Filter Based on Cascaded Grating-Assisted Contra-Directional Couplers in Silicon Nitride Rib Waveguides

Ultra-Broadband Optical Filter Based on Step-Chirped Multimode Waveguide Bragg Grating

Narrow-Band Add-Drop Filter Based on Phase-Modulated Grating-Assisted Contra-Directional Couplers

Fibre-optic Comb Filter with Tunable Central Wavelength and Channel Isolation at Sub-Microsecond Speed

High-efficiency Wideband SiNx-on-SOI Grating Coupler with Low Fabrication Complexity.

High-efficiency Grating Coupler Based on Fast Directional Optimization and Robust Layout Strategy in 130 Nm CMOS Process.

Inverse Design of the Multimode Bragg Grating Based on Time-Domain Layer Peeling Method

A reconfigurable photonic microwave channelized receiver based on an optical comb

Birefringence compensated arrayed waveguide grating

Silicon Band-Rejection and Band-Pass Filter Based on Asymmetric Bragg Sidewall Gratings in A Multimode Waveguide

Design and characterization of novel comb filters based on periodical fiber Bragg gratings

Design and fabrication of 1 × 32 silica-based arrayed waveguide grating

In-line flat-top comb filter based on a cascaded all-solid photonic bandgap fiber intermodal interferometer.

128 Channels of Integrated Filter Array Rapidly Fabricated by Using the Combinatorial Deposition Technique

Silica-Based Arrayed Waveguide Grating With Flattened Spectral Response Using A Multimode Interference Coupler

Integrated Broadband Filter with Sharp Transition Edges Based on SiN and SiON Composite Waveguide Coupler