Abstract:For improving the wear resistance of Al-30Si-5Cu coating, in this study, the composite coating in-situ synthesized TiC-TiN-TiN 0.8 C 0.2 /Al-30Si-5Cu (TiCN/Al-30Si-5Cu) was prepared used TiH 2 -graphite aggregates as raw materials and plasma spraying technology. The effect of in-situ synthesized ceramic reinforcements on the coating was researched in detail. The results showed that during the plasma spraying process, TiH 2 decomposed and chemically reacted with graphite to form TiC. Additionally, some Ti also reacted with N 2 and O 2 in the air to form TiN and TiO 2 . The phases composition of TiCN/Al-30Si-5Cu composite coating were α-Al, β-Si, θ-Al 2 Cu, β-Ti, TiC, TiN, TiN 0.8 C 0.2 , TiO 2 , as well as amorphous CN X and residual graphite. The TiC-dominated ceramic phases and β-Si were uniformly distributed in the coating, which were tightly bound to the α-Al matrix. Because of the exceptionally rapid cooling rate during the coating preparation, a minor amount of submicron Si particles were also generated. The microhardness, elasticity modulus, and fracture toughness of TiCN/Al-30Si-5Cu composite coating appeared improvements compared to those of Al-30Si-5Cu coating. The TiCN/Al-30Si-5Cu composite coating exhibited smoother friction coefficient curve, along with lower friction coefficient and wear volume in comparison to the Al-30Si-5Cu coating. This suggested that the ceramic reinforcing phases in-situ synthesized led to a notable advancement in the wear resistance of the TiCN/Al-30Si-5Cu composite coating. The wear resistance of TiCN/Al-30Si-5Cu composite coating demonstrated an increasement of 78.3 % over the substrate and 28.2 % over the Al-30Si-5Cu coating. Under the dry friction test conditions outlined in this study, the wear mechanism of the TiCN/Al-30Si-5Cu composite coating included abrasive wear and fatigue wear, coupling with a minimal amount of oxidative wear.

Combustion synthesis of Al2O3 ceramic coating and its application

An Experimental Study on Combustion Synthesizing of Plane Ceramic Coating

Preparation of Micro-Arc Oxidation Ceramic Coating on Aluminum Alloys

Preparation and properties of Al2O3/Al-2(1-0.2)Mg0.2Ti(1+0.2)O5 matrix ceramic composite

Microstructure and mechanism of Al2O3-ZrO2 eutectic coating prepared by combustion-assisted thermal explosion spraying

Present Status and Development of Combustion Synthesizing of Ce- ramic Coating

Fabrication of Cr3C2-AlN-FeCr cermet coating by combustion synthesis

Preparation of Self-Coating Al2O3 Bonded SiAlON Porous Ceramics Using Aluminum Dross and Silicon Solid Waste under Ambient Air Atmosphere

Formation Mechanism for Al2O3-based Ceramic Coatings on Aluminum Alloy Substrates

Study on the Microstructure of Anti-Corrosion and Wear Resistant Coating on the Inner Wall of Equipment Pipeline and the Synthesis Mechanism of Ceramic Coating

Influence of Nano SiC on Phase Composition and Properties of Inside Ceramic Lining Coating Prepared on Composite Pipes by Gravitational Separation Self-Propagation High-Temperature Synthesis

One zirconia-based ceramic coating strategy of combustion stabilization for fuel-rich flames in a small-scale burner

Micrographic Properties of Composite Coatings Prepared on TA2 Substrate by Hot-Dipping in Al–Si Alloy and Using Micro-Arc Oxidation Technologies (MAO)

Preparation and properties of Al2O3-PF composite functional protective coating on the surface of polymer matrix composites

Effect of Al2O3 addition on the microstructure and oxidation behavior of SiC coating prepared by pack cementation on C/C composites

Microstructure and tribological properties of Al-30Si-5Cu composite coating reinforced with ceramic phases synthesized in situ by plasma spraying

Fabrication of Composite Coating Particles with Mullite Stoichiometric Ratio by a Novel Processing

Wear-resistant ceramic coatings deposited by liquid thermal spraying

In-situ preparation and oxidation behavior of MgAl 2 O 4 -containing ceramic/metal composite coatings via hot dipping

Tribological and corrosion performance of the plasma-sprayed conformal ceramic coating on selective laser melted CoCrMo alloy

Controllable in situ fabrication of self-lubricating nanocomposite coating for light alloys