Abstract:In this work, high energy synchrotron X-ray diffraction was used during tensile testing of an as-cast eutectic AlCoCrFeNi2.1 high entropy alloy. Aside, from determining for the first time the volume fractions of existing phases, we further detail their role on the alloy deformation behavior. The two major phases, a soft disordered FCC and a hard ordered B2 BCC, were observed to exhibit a stress partitioning effect which can be used to modulate the mechanical response of the material based on the relative volume fraction of each phase. Dislo-cation density analysis revealed that the soft FCC phase had a significantly higher dislocation density right after the onset of plastic deformation. This is attributed to the existence of strain gradients across the lamellar structure, where the hard B2 BCC prevents free deformation of the FCC phase. Nonetheless, despite the increase of the dislocation density in the soft FCC phase, calculations of the strengthening effects induced by generation of dislocations are more significant in the hard B2 BCC phases, as this phase is primarily responsible for the strength increase in the alloy. Besides, the evolutions in dislocation density of the soft FCC and hard B2 BCC phases during tensile deformation obtained from synchrotron X-ray diffraction data are consistent with the evolution of KAM determined by EBSD characterization. Also, lattice strain analysis across two principal directions (parallel and perpendicular to the loading axis) reveals that for these specific orientations there is a preferential deformation of the hard FCC planes which can be related to the deformation response of specific lattice planes at distinct ori-entations, as well as to the phase partitioning stress behavior.

Determination of elastoplastic properties of individual phase in solidified Al brazed joint

Topological Dependence of Mechanical Responses of Solidification Microstructures in Aluminum Brazed Joints

Microstructures Characteristics and Properties of Solidified Aluminum Alloy Brazed Joint

Mechanical Response of Reaction Phases of the Tial/Steel Brazed Joint under A Tensile Load

Characteristics of reaction phases and effects of phases on mechanical properties of TiAl/42CrMo steel brazed joint

Investigations of the microstructure and mechanical properties of the Nb-Ti/Nb-Ti-Ni brazed joints

Solid state Si diffusion and joint formation involving aluminum brazing sheet

Strain Field and Fracture Behavior of Ti/Al Dissimilar Alloy Joint under in Situ Tensile Test

Influence of Si content on interfacial reactions and mechanical properties of dual-spot laser welded-brazed Ti/Al joints

Microstructural evolution and mechanical properties in the self-propagating brazing joint of Al 0.1 CoCrFeNi HEAs and 304 SS using reactive multilayer nanofoils

Relationship between microstructure and mechanical properties of TiAl/Ti2AlNb joint brazed using Ti-27Co eutectic filler metal

Prediction of the Fillet Mass and Topology of Aluminum Brazed Joints

Interfacial Microstructure and Mechanical Properties of Induction Brazing TiAl/40Cr Joints

Secondary Phase Interaction at Interfaces of High-Strength Brazed Joints made using Liquid Phase Sintered Alumina Ceramics and Ag-Cu-Ti Braze Alloys

Mechanical Behavior Assessment of Ti-6Al-4V ELI Alloy Produced by Laser Powder Bed Fusion

Interfacial structure and properties of reactive brazing joints of TiAl/Ni-based alloy

Microstructure and mechanical properties of Al/Ti brazed joints by using pure Al interlayer

Preparation of Zn-based Alloy Filler for Brazing Aluminum and Microstructure and Shear Strength of Brazed Joint

Deformation Behavior and Strengthening Effects of an Eutectic AlCoCrFeNi2.1 High Entropy Alloy Probed by In-Situ Synchrotron X-ray Diffraction and Post-Mortem EBSD

Microstructure and Joint Properties of Ultrasonically Brazed Al Alloy Joints Using a Zn–Al Hypereutectic Filler Metal

Phase analysis and corrosion behavior of brazing Cu/Al dissimilar metal joint with BAl88Si filler metal