Abstract:Inconel 617 nickel-based superalloy with 3 mm wall thickness was welded by laser beam using two different heat input welding parameters. The microstructure of the welded joint was observed by optical microscope and scanning electron microscope, and the mechanical properties of the welded joint at room temperature (25celcius) and high temperature (900celcius) were tested. The results show that the laser welding heat input has a significant effect on the microstructure and mechanical properties of Inconel 617 welded joints. The front width of the laser weld obtained by high heat input (200 J/mm) process parameters is 3.88 mm. The grain size in the middle of the weld fusion zone is coarse, and the grain orientation is disordered. The secondary dendrite arm spacing in the middle of the weld is large (6.71 mu m). The carbide particle size between the dendrites is coarse, and the solidification microsegregation of Mo, Cr alloy elements is serious. The width of heat affected zone is about 0.29 mm. The eutectic structure of gamma+carbide is formed in the grain boundary and grain interior. This is because during the heating process of the welding, the spherical carbide particles and the surrounding austenite in the heat-affected zone liquefy and the eutectic structure is formed during the solidification process after welding. The front width of the laser weld obtained by low heat input (90 J/mm) process parameters is 2.28 mm, the grains inside the weld are columnar which is formed by epitaxial growth along the fusion line and directional solidification along the heat flow direction. The secondary dendrite arm spacing in the middle of the weld is small (2.26 mu m), the carbide particles between dendrites are small, and the width of heat affected zone is about 0.15 mm. The tensile strength test at room temperature (25celcius) shows that the welded joints obtained under high heat input fracture from the middle of the weld, and the tensile strength and elongation decrease, which is caused by the segregation of solid solution elements in the weld. The welded joints obtained under low heat input fracture from the base metal. At high temperature (900celcius), all samples fracture from the base metal, which is due to the weakening of the grain boundary of the base metal at high temperatures.

Elastic modulus and hardness characterization for microregion of Inconel 625/BNi-2 vacuum brazed joint by high temperature nanoindentation

Use of Instrumented Micro-Indentation to Study the Mesoscopic Elasto-Plastic Behavior of Gh4145/Sq Superalloy During High-Temperature Cyclic Straining

Mechanical Properties of Micro-phases Along < 001 > Direction of Directionally Solidified Nickel-base Super-alloy by In-situ Nano-Indentation

High-throughput nanoindentation mapping of cast IN718 nickel-based superalloys: influence of the Nb concentration

Temperature dependence of deformation behavior, microstructure evolution and fracture mechanism of Inconel 625 superalloy

Microstructure and Properties of Vacuum-Brazed Joints of 3D-Structured Ni718 High-Temperature Alloy Prepared by Selective Laser Melting

Microstructure and High Temperature Fracture Toughness of NG-TIG Welded Inconel 617B Superalloy

Study on the microstructure and mechanical properties of Ti-Zr-Cu-Ni amorphous filler brazed Inconel 718 and 3D printed TC4 alloy

In-situ SEM study of temperature-dependent tensile behavior of Inconel 718 superalloy

Investigations of the microstructure and mechanical properties of the Nb-Ti/Nb-Ti-Ni brazed joints

Metallurgical characterization and high-temperature tensile failure of Inconel 617 alloy welded by GTAW and SMAW—a comparative study

Microstructural evolution and mechanical properties of Ni-based superalloy joints brazed using a ternary Ni-W-B amorphous brazing filler metal

Microstructural characteristics and mechanical response of diffusion bonding Inconel 617 superalloy

Microstructural and Mechanical Characterizations of Mo/W and Mo/Graphite Joints with BNi2 Paste

Effect of heat input on microstructure and mechanical properties of laser welded joint of Inconel 617 nickel-based superalloy

Microstructure and mechanical properties of C/C composite joint brazed with Ni-based filler

Microstructure and mechanical properties of ZrB 2 ‐SiC/Nb joints brazed with CoFeNiCrCuTi x high‐entropy alloy filler

Microcrack Nucleation and Propagation Investigation of Inconel 740H Alloy under in Situ High Temperature Tensile Test

Hot Deformation Behavior and Dynamic Recrystallization Nucleation Mechanisms of Inconel 625 during Hot Compressive Deformation

Effect of brazing temperature on the interfacial microstructure and mechanical properties of GH3039 joint brazed with electroless Ni–P filler metal

Creep strength and toughness synergistic strengthening mechanism investigation of the Inconel625/ BNi-2 brazed joint