Abstract:With the increasing depletion of high-quality raw materials, siliceous limestone, sandstone and other hard-to-burn raw materials containing crystalline SiO2 are gradually being used to produce clinker. This study investigates the influence of the quartz content and particle size in siliceous limestone on the calcination process and the resultant quality of cement clinker. Two different siliceous limestones were grinded to different fineness, and calcinated with some other materials. The content of the clinkers was analyzed with the XRD–Rietveld method and the microstructure of the clinkers was observed with laser scanning confocal microscopy (LSCM) and field emission scanning electron microscopy (FESEM). Three key outcomes of this study provide new insights on the use of siliceous limestone in cement production, namely that (i) reducing the fineness values of siliceous limestone from 15% to 0% of residue on a 0.08 mm sieve decreases the quantity of these larger quartz particles, resulting in an increase in C3S content by up to 8% and an increase in 28d compressive strength by up to 4.4 Mpa, which is 62.30 Mpa; (ii) the morphology of quartz—either as chert nodules or single crystals—affects the microstructure of C2S clusters in clinker, finding that chert nodules result in clusters with more intermediate phases, whereas large single crystals lead to denser clusters; (iii) the sufficient fineness values of siliceous limestone SL1 and SL2 are 5% and 7% of residue on a 0.08 mm sieve, respectively, which can produce a clinker with a 28d compressive strength greater than 60 Mpa, indicating that for different kinds of quartz in siliceous limestone, there is an optimum grinding solution that can achieve a balance between clinker quality and energy consumption without having to grind siliceous limestone to very fine grades.

STUDY ON THE EASILY GRINDING PORTLAND CEMENT CLINKER

Utilization of Coal Gangue and Copper Tailings As Clay for Cement Clinker Calcinations

Composition design and pilot study of an advanced energy-saving and low-carbon rankinite clinker

Effects of clinker contents of different C3A and C4AF on the performance of PSC cement

Effects of Fineness and Morphology of Quartz in Siliceous Limestone on the Calcination Process and Quality of Cement Clinker

Influence of Mechanical Grinding on Pozzolanic Characteristics of Circulating Fluidized Bed Fly Ash (CFA) and Resulting Consequences on Hydration and Hardening Properties of Blended Cement

Investigation on the Micro-Grinding Induced Crystallographic Variations of Nine Different Clinkers

Study on the finely ground steel slag as high reactivity blending materials of cement

Rapid-setting and hardening, high-belite sulfoaluminate cement clinker as well as application and production process thereof

Effect of Steel Slag on Burnality of Cement Raw Meal

High-Volume Mineral Admixtures Cement: The Effects of Particle Size Distribution

Influence of Mechanical Grinding on Particle Characteristics of Coal Gasification Slag

Properties and microstructure of a low-carbon clinker-free cementitious binder and its extrusion-based printing performance

Effect of CuO on the Burnability and Mineral Formation of High C3S Cement Clinker

Microstructure of Hardened Complex Binder Pastes Blended with Slag

Study on Strength and Microstructure of Cement-Based Materials Containing Combination Mineral Admixtures

Influence of mechanical grinding on the cementitious properties of coarse particles in steel slag

Preparation and characterization of Portland cement clinker from sulfuric acid leaching residue of coal fly ash

AN EXPERIMENTAL STUDY ON MAKING CEMENTING MATERIAL WITH RECYCLED POWDER AND STEEL SLAG

Characterization and Comparison of the Grindability, Residual Compressive Strength, and Hydrated Phases of Traditional Cement Prepared from Lime Rock and Carbide Slag

Unveiling the key factors for clinker reactivity and cement performance: A physic-chemical and performance investigation of 40 industrial clinkers