Abstract:The effect of major constituents (the Li content increases from 0.5 to 3 wt% and the Cu content decreases from 4.5 to 2 wt%) on microstructure and mechanical properties of cast Al-Li-Cu-Zr alloy were studied to understand a qualitative assessment of sequence and kinetics of multiple precipitations. Increasing the Li content progressively raises the melting temperature from 520 °C in 1# alloy (Al-0.5Li-4.5Cu, wt%) and 2# alloy (Al-1Li-4.5Cu) to 560 °C in 6# alloy (Al-3Li-2Cu). In addition, the variations of the major constituents result in the changes of the type and volume fraction of the inter- and intra-granular intermetallic phases. TEM results indicate that minor modifications to alloy composition greatly alter precipitation behavior during isothermal aging. The Li-poor alloy (2# alloy) presents a much shorter incubation time of T1-Al2CuLi precipitate than the Li-rich alloy (Al-1.5Li-4.5Cu, 3# alloy), while the nucleation of θ'-Al2Cu precipitate is promoted in Li-rich alloy. No typical spherical δ'-Al3Li precipitate is observed in 2# and 3# alloys during isothermal aging, except for the as-quenched 3# alloy. The preferential nucleation of δ' precipitate on the coherent and broad face of θ' precipitate is observed in 2# and 3# alloys, leading to the formation of "sandwich-like" δ'/θ'/δ' phases. Further decreasing Cu content to 2 wt% and increasing Li content to 3 wt% (6# alloy), the predominant phase in the matrix is δ' precipitate, accompanied by a small amount of unevenly distributed θ' and T1 precipitates. The best balance between ductility and strength is obtained by 2# alloy aged for 32 h, but 6# alloy has significant advantages in terms of density (2.437 g/cm3) and elastic modulus (82.65 GPa) over 2# alloy (density: 2.675 g/cm3; elastic modulus: 75.45 GPa).

Small-angle X-Ray Scattering Study of the Formation and Growth of Δ' in Binary Al-7.87at% Li Alloy

Atomic-scale study on the precipitation behavior of an Al-Zn-Mg-Cu alloy during isochronal aging

Small angle X-ray scattering study of the strengthen mechanism of Al–Mg–Li alloy during retrogression and reaging treatment

Coarsening of delta' (Al3Li) Precipitates in Aluminum-Lithium Alloys

Evolution of aging precipitates in an Al–Li alloy with 1.5 wt% Li concentration

The influence of Cu/Li ratio on precipitation in Al–Cu–Li–x alloys

Microstructural evolution and mechanical properties of the rapidly-solidified and hot-extruded 2196 Al-Li alloy

Computer simulation of the atomic picture for δ′(Al3Li) precipitation in Al-Li alloy

Disclosing Differential Precipitation Behavior of a Novel High Mg-containing Al-Mg-Zn-Si Alloy

Size distribution and coarsening kinetics of δ′ precipitates in Al–Li alloys considering temperature and concentration dependence

Microstructures and Mechanical Properties of a L12-structured Precipitation Strengthened Co-based Superalloy

In-situ small-angle neutron scattering study of the growth and dissolution of precipitates in Al-Li alloys

Microstructure evolution and shearing behaviour of δꞌ/θꞌ/δꞌ precipitates in an aged Al-Cu-Li-Mg aluminium alloy

Study on the microstructure and age hardening capability in Al–Cu–Li alloys with different Cu/Li ratio

Precipitation behavior in the early stage of aging in an Al–Li°Cu–Mg–Zr–Ag (Weldalite 049) alloy

Investigations on Ordering and Atom Clustering in Al-Li Alloy by Computer Simulation

Continuous precipitate modes of the δ′-Al3Li phase in Al-Li alloys

The effect of major constituents on microstructure and mechanical properties of cast Al-Li-Cu-Zr alloy

Yield characteristics of aluminium–lithium alloys

Microstructural evolution, precipitation behavior and mechanical properties of a novel Al–Zn–Mg–Cu–Li–Sc–Zr alloy

Insight into the aging behavior of a novel Al-Li-Cu-Mg alloy