Abstract:SiC layer was prepared in an industrial scale spout fluidized bed by chemical vapor deposition. The density of SiC coating was about 3.18 g/cm(3). High temperature oxidation experiments were carried out at different temperatures from 800 to 1600 degrees C. The microstructure and composition were characterized using different methods, including mass change weighing, XRD, EDS and SEM. It was found that the weight gain of SiC coating layer was not obvious below 1200 degrees C, and subsequent mass gain gradually increased with increasing temperature, reaching 10% at 1600 degrees C. High-magnification SEM results show that the oxidation began from the surface and gradually formed punctate distribution of the oxide. Small crystal structure (similar to micron) of the SiC surface was very clear at 1000 degrees C, and this crystal structure disappeared gradually at high temperatures, forming oxides of Si in the SiC surface. There was a stacking fault stress due to the different thermal expansion coefficients and elastic modulus of SiC and Si oxides, leading to the gradual formation of cracks around the punctates. With increasing temperature, the crack further increased the oxidation rate of SiC, and finally the formed Si oxides layer fell off from the particles. It can be seen clearly that the layer was peeling when the temperature was increased to 1400 degrees C. Increasing the temperature to 1600 degrees C, the SiC coating was oxidized completely into a honeycomb structure, with obvious sintering of SiC. XRD analysis shows that there was a growing SiO2 peaks from 1400 degrees C, indicating that surface oxidation was significant. EDS results shows that the oxygen content in the coating surface gradually increased with increasing temperature. Semi-quantitative analysis shows that the surface was close to SiO2 at 1600 degrees C.

Thermal Expansion and Oxidation of 3D C/SiC Composites with Different Coatings from Room Temperature to 1400°C

Microstructure and oxidation behavior of SiOC coatings on C/C composites co-deposited with HMDS and TEOS by using CVD process

Influence of SiC Coating Thickness on Mechanical Properties of SiCf/SiC Composite

Thermal Expansion Behavior of Carbon Fiber Reinforced Chemical-Vapor-infiltrated Silicon Carbide Composites from Room Temperature to 1400 °C

EFFECTS OF HEAT TREATMENT ON THERMAL EXPANSION OF 3D C/SiC COMPOSITES

High Temperature Oxidation Behavior of SiC Coating Materials

Effects of interphases on thermal expansion of 3D-C/SIC composites

Oxidation behavior of 3D Hi–Nicalon/SiC composite

Effects of Interphase Thickness and Heat Treatment on Transverse Thermal Diffusivity of 3 D C / SiC Composites

High-Temperature Fatigue Degradation Behaviors of a 3D Braided C/SiC with a Thin Interlayer in Different Dry Oxygen Atmospheres

Oxidation behavior of 3D SiCf/SiBCN composites at 800–1200 °C

Interfacial modification and oxidation resistance behavior of a CVD-SiC coating for C/SiC composites

Thermal Protection and Dielectric Properties of Borosilicate Coatings for SiCf/SiC Composites Under High-Temperature Oxidation

Effect of SiC coating and heat treatment on damping behavior of C/SiC composites

Comparison of Oxidation Behaviors of 3D C/PyC/SiC and SiC/PyC/SiC Composites in an O2-Ar Atmosphere

Influence of the heat treatment on mechanical properties and oxidation resistance of SiC–Si3N4 composites

Deposition voltages on the phase evolutions, microstructures, and oxidation behaviors of thermal-resistance Glass-MoSi2-SiC coating

Effect of oxidation on internal friction behavior of C/SiC composites

Unveiling high-temperature stability and growth dynamics of CVD-SiOC coatings across different deposition conditions and environments

High-temperature tensile behavior of 3D SiC/SiC composites

Oxidation behaviors of carbon fiber reinforced multilayer SiC-Si3N4 matrix composites