Abstract:To investigate how laser peen texturing (LPT) parameters affect the patterns formed on the surface of E690 high-strength steel, and how these patterns subsequently influence tribological properties, the LPT process, including multiple shocks, was simulated by ABAQUS and verified by experiments. The residual stress and microstructure on the surface of micro-dimples after LPT were measured and observed by X-ray stress analyzer and transmission electron microscope. The tribological properties of specimens with different LPT density and depth were tested by reciprocating friction experiments, and the worn surfaces were observed using a scanning electron microscope. The experimentally obtained plastic deformation depths of the micro-dimples were − 8.82 μm, −18.31 μm, −28.72 μm and − 36.34 μm when the shock number was varied from 1 to 4. The simulation and experiment results were within 3.3 %, verifying the accuracy and reliability of the simulation. When the shock number was ≥ 2, the residual stress values in all directions at the test points within the micro-dimples tended to be consistent, and the full width at half maximum (FWHM) values gradually increased with increasing shock number. The TEM images and electron diffraction pattern of the specimen after three shocks showed that nanocrystals are formed on the bottom surface of the micro-dimple. In the friction experiments, the average friction coefficient first decreased and then increased with increasing LPT density. The average friction coefficient was the lowest when the LPT density was 20 %, for a constant micro-dimple depth. When the LPT density was 20 %, increasing the micro-dimple depth had little effect on the average friction coefficient, but the stability time of the specimens increased substantially. The wear surface of the untextured specimen showed deep and wide wear marks, and serious abrasive wear and adhesive wear occurred. Suggested LPT parameters for optimum wear resistance are an LPT density of 20% and shock number of 3.

Effect of Surface Roughness of Steel on Morphology of Laser-textured Micro-convex

Laser Texturing of Rolled Surfaces

Laser Surface Texturing of Stainless Steel − Effect of Pulse Duration on Texture's Morphology and Frictional Response

Investigation of Micro-wear and Micro-friction properties for bionic non-smooth concave components

Friction and Wear Behavior of 316L Stainless Steel with Laser Micro-Hole Texture and Micro-Square-Column Array Texture

Effect of laser shock peening on the retention ability of surface roughness in forged Cr5 steel

Analysis of synergistic friction reduction effect on micro-textured cemented carbide surface by laser processing

Anti-Wear Property of Laser Textured 42CrMo Steel Surface

Surface morphological evolution and microhardness change of Cr12MoV steel by pulsed laser polishing

Impact wear behavior of laser hardened hypoeutectoid 2Cr13 martensite stainless steel

Surface morphology evolution mechanisms of pulse laser polishing mold steel

Laser Melting and Surface Texture Technology: Effect on Friction Properties

Experimental study on laser peen texturing and tribological properties of E690 high-strength steel

Additional Tribological Effect of Laser Surface Texturing and Diamond-Like Carbon Coating for Medium Carbon Steel at Near Room Temperature

Effect of Laser Quenching-Shock Peening Strengthening on the Microstructure and Mechanical Properties of Cr12MoV Steel

Surface morphology evolution and tribological behavior in nanosecond pulsed laser polishing of S136 mold steel

Microstructure Distribution and Grain Coarsening Model of GCr15 Steel in the Laser Surface Treatment

Effects of Laser Quenching on Impact Toughness and Fracture Morphologies of 40CrNiMo High Strength Steel

The Effects of Laser‐Assisted Ultrasonic Nanocrystal Surface Modification on the Microstructure and Mechanical Properties of 300M Steel

Effect of Nanosecond Laser Texturization on Tribological Behavior of AISI 321 Stainless Steel

An Experimental Study in Laser-Assisted Machining of AerMet100 Steel