Abstract:Herein, we present the results of an experimental study on the mechanical properties of Fe-C alloys with different carbon contents (0.2, 0.45, and 0.8%) in a wide range of deformation rates (10−3–103 s−1) and abrasive wear resistance, which underwent combined laser thermal (laser surface hardening—LSH) and laser shock wave (Laser Shock Peening—LSP) processing. The combined treatment modes included a different sequence of exposure to laser thermal and laser-induced shock pulses on the material. The amplitude and duration of laser-induced shock waves were measured using a laser Michelson interferometer. The mechanical properties of steel samples were studied under conditions of uniaxial tension under static loads on a standard universal testing machine, the LR5KPlus, and under dynamic loading, tests were carried out on a specialized experimental complex according to the H. Kolsky method using a split Hopkinson rod. The abrasive wear resistance of hardened surfaces was studied using the Brinell–Haworth method. Studies have shown that the use of a combination of LSH and LSP treatments leads to an increase in both the mechanical properties of steels and abrasive wear resistance compared to traditional laser hardening. It has been established that in the combinations considered, the most effective is laser treatment, in which LSP treatment is applied twice: before and after LSH. Thus, after processing steels using this mode, an increase in the depth of the hardened layer was recorded—by 1.53 times for steel 20, by 1.41 times for steel 45, and by 1.29 times for steel U8—as well as a maximum increase in microhardness values by 22% for steel 20, by 27% for steel 45, and by 13% for U8 steel. The use of this mode made it possible to obtain the maximum strength properties of the studied materials under static and dynamic loading, which is associated with an increase in the volume fraction of the strengthened metal and high microhardness values of the strengthened layer of traditional LSH. The dependences of abrasive wear of the studied steels after various combinations of LSP and LSH impacts were established. It is shown that the greatest wear resistance of the studied steels is observed in the case when the LSH pulse is located between two LSP pulses. In this case, abrasive wear resistance increases by 1.5–2 times compared to traditional LSH.

Impact wear behavior of laser hardened hypoeutectoid 2Cr13 martensite stainless steel

Microstructure and wear behavior of arc-shaped 40CrNiMo steel after laser hardening

Characterization of a Laser Surface-Treated Martensitic Stainless Steel

Fatigue crack initiation and growth of laser shock peened 2Cr13 martensitic stainless steel as a function of the coverage layer

Wear Characteristics of Carbon and Tool Steels Hardened by Combined Laser-Ultrasonic Surface Treatment

Effects of Laser Quenching on Impact Toughness and Fracture Morphologies of 40CrNiMo High Strength Steel

Effect of Combined Laser Thermal and Shock Wave Effects on the Mechanical and Tribological Properties of Steels

Effect of distribution status of the spot matrix on tensile behavior for 42CrMoV when conducting discrete laser surface strengthening: Based on experiment and simulation

Laser shock peening-induced carbide evolution and remarkable improvement in electrochemical and long-term immersion corrosion resistance of 2Cr12NiMoWV martensitic stainless steel

Effect of laser surface hardening on a low carbon steel substrate wear and hardness

Impact of Laser Shock Processing on Microstructure and Tribological Performance of GCr15 Bearing Steel

Microstructure refinement and properties of 1.0C-1.5Cr steel in a duplex treatment combining double quenching and laser surface quenching

Microstructure stability and high temperature wear behavior of an austenite aging steel coating by laser cladding

Effects of Laser Scanning Rate and Ti Content on Wear of Novel Fe-Cr-B-Al-Ti Coating Prepared via Laser Cladding

Microstructural characteristics, hardness and wear resistance of a typical ferritic/martensitic steel surface-treated by pulsed laser

Study on laser surface hardening process of 30CrMnSiNi2A ultra-high strength steel fabricated by laser deposition manufacturing

Effect of laser shock peening on the retention ability of surface roughness in forged Cr5 steel

Friction and Wear Behavior of 316L Stainless Steel with Laser Micro-Hole Texture and Micro-Square-Column Array Texture

Effect of Cryogenic Treatment on the Microstructure and Mechanical Properties of Selected Laser Melted H13 Steel

Effects of laser heat treatment combined with ultrasonic impact treatment on the surface topography and hardness of carbon steel AISI 1045

Effect of the Laser Cladding Parameters on Microstructure and Elevated Temperature Wear of FeCrNiTiZr Coatings