Abstract:TiN coatings are commonly used in industry to impart improved friction and wear performance. It is widely recognised that the substrate plays an important role in determining the mechanical properties and wear resistance of such coatings. TiN coatings are usually applied to hard tool steels where there is substantial load support from the substrate. However, there are many applications where it may be desirable to apply the coatings to substrates with lower hardness or stiffness values than the conventional, hard tool-steel substrates that are commonly used. Coatings can still be effectively used in these applications. However, it is then critical to understand the transitions between where the deformation is contained solely in the coating and where it is a combination of coating/substrate properties that are important in determining the overall mechanical response of the system. This paper therefore reports on a systematic investigation of the effect of the substrate on the mechanical response using a range of mechanical testing techniques. A TiN coating was deposited using ion-assisted PVD onto a number of substrates with differing combinations of modulus and hardness [i.e. a range of Young's modulus (E) to yield stress (Y) E/Y ratios]. The mechanical properties of these coatings have been investigated using nanoindentation, microindentation and scratch testing, and the deformation was observed using scanning electron microscopy. In the microindentation tests, nested cracks were observed around the indentations. In the nanoindentation tests, the indentation response was found to be plasticity-dominated, with little evidence of cracking. The scratch tests showed that the scratch response was controlled by plastic deformation in the substrate, and that the friction coefficient increased as the depth of penetration into the sample increased. For the coatings here, it was observed that the indentation depth/coating thickness ratio required for the deformation to be contained within the coating was less than the usual t/10 ratio.

Micromechanical Characterization of TiN Films on 9cr18 Steels

Tribological Characteristics of TiN and TiCN Hard Coatings Prepared by Pulsed D.C. Plasma Enhanced Chemical Vapour Deposition

The effect of the substrate on the mechanical properties of TiN coatings

Mechanical Properties of Ti(C(0.7)N(0.3)) Film Produced by Plasma Electrolytic Carbonitriding of Ti6al4v Alloy

Investigations on microstructure, mechanical and tribological properties of TiN coatings deposited on three different tool materials

Ti/TiN multilayer coatings: deposition technique, characterization and mechanical properties

The study of the adhesion of a TiN coating on steel and titanium alloy substrates using a multi-mode scratch tester

Microstructures and Mechanical Properties of (Ti,Cr)N Composite Coatings Grown by Arc Ion Plating

Microstructure, Mechanical, and Tribological Properties of Cr-Ti-Si-N Coatings

Tribological Characterization of Ti-Si-N Nano Films Prepared by Reactive Magnetic Sputtering

Microstructure and properties of TiCrN coatings by arc ion plating

Fabrication and Performance of TiN/TiAlN Nanometer Modulated Coatings

The Tribological and Structural Characterization of Nano-Structured Ti–Si–N Films Coated by Pulsed-D.c. Plasma Enhanced CVD

Micro/Nanotribological and Mechanical Studies of Tin Thin-Film for Mems Applications

Surface properties of TiN thin film on spinning and weaving scissor made of W9Mo3Cr4V steel

Nanoindentation and Tribological Behavior of TiN-TiCN-TiAlN Multilayer Coatings on AISI D3 Tool Steel

ADHERENT NANO-SUPERHARD TITANIUM NITRIDE FILM AND ITS FORMING MECHANISM IN MULTI-ARC ION-PLATING SYSTEM

Analysis Of The Mechanical Properties Of Tin/Ti Multilayer Coatings Using Indentation Under A Broad Load Range

Characterisation of TiCN Coatings for Biomedical Applications

Comparative investigation and characterization of the nano-mechanical and tribological behavior of RF magnetron sputtered TiN, CrN, and TiB2 coating on Ti6Al4V alloy

Friction and wear characteristics of nano-structured Ti-Si-N films on a high speed steel substrate prepared by pulsed-direct current plasma enhanced chemical vapor deposition