Abstract:A new three-step method for preparing aluminum rich coating on HR-2 stainless steel was proposed, i.e. ambient temperature chloroaluminate melts electroplating followed by heat treating and artificial oxidation. In the electroplating process, aluminum deposition from AlCl3/MEIC to the surface of HR-2 steel was performed with a deposition rate of 15 mu m/h. Within the aluminizing temperature range from 650 to 750 degrees C, aluminizing time from 1 to 30 h, the aluminized coating with thickness of 3-27 mu m can be prepared, which is homogeneous and free of porosity or crack, and have good metallographic adherence to the substrate; the coating cross section exhibits a three-layer or two-layer structure. A simple Arrhenius relationship can be used to describe the effect of temperature on the coating growth rate, which gives activation energy of 116.9 kJ/mol. The relationship between the coating thickness against time(1/2) is approximately linear, which is a typical feature of the diffusion controlled coating growth mechanism. To form Al2O3 film on surface, the aluminized coating treated for 4 h was oxidized in 10(-2) Pa O-2 for 80 h and observed by X-ray photoelectron spectroscopy (XPS) and Reflection spectrum. The finally fabricated coating shows a double-layer structure consisting of an outer gamma-Al2O3 layer with thickness of 110 nm and inner (Fe,Cr,Mn and Ni)Al/(Fe,Cr,Mn and Ni)(3)Al layer of 30 mu m thickness, and is homogeneous without any defects. The deuterium permeation rate through the coated HR-2 steel is reduced by 3 orders of magnitude at 600 degrees C. The coating remains a perfect surface for 20 thermal cycles between 750 degrees C and room temperature. The method is a potential candidate for preparation of TPB on the tritium container surface in ITER.

Preparation and Releasing Hydrogen Characteristic of Al2O3-Coated TiH2 Particles

Preparation of Al2O3-coated TiH2 Foaming Reagent by Chemical Method

Preparation and hydrogen storage characteristics of Ti-NaAlH4 complex hydride

Coating process of silica film on TiH2 particles and hydrogen release characteristics

The effect of SiO2 and Al2O3 coating on the surface of TiH2 powders on gas release.

Film-Coating Process of Hydrated Alumina on TiO<sub>2</sub>Particles

Catalytically ultrathin titania coating to enhance energy storage and release of aluminum hydride via atomic layer deposition

Effect of SiO2 coating layer morphology on TiH2 gas release characteristic.

A new preparing method and performances of FeAl/Al2O3 tritium permeation barrier

Preparation of TiO2‐Coated Al2O3 Particles by Chemical Vapor Deposition in a Rotary Reactor

The Hydrogen Storage Properties and Microstructure of Ti-Doped Sodium Aluminum Hydride Prepared by Ball-Milling

The coating process of silica film on TiH2 particles and gas release characteristic

Preparation and magnetic properties of Al2O3-coated acicular α-Fe particles

Influence of Temperature and Hydrogen Pressure on the Hydriding/dehydriding Behavior of Ti-doped Sodium Aluminum Hydride

Directed Stabilization by Air-Milling and Catalyzed Decomposition by Layered Titanium Carbide Toward Low-Temperature and High-Capacity Hydrogen Storage of Aluminum Hydride

Formation of Na3AlH6 from a NaH/Al Mixture and Ti-containing Catalyst

Structural and Hydrophilic Properties of TiN Films Prepared by Ultrasonic Atomization Assisted Spray Method under Low Temperature

Influences Of Agglomeration Powder Preparation On Deposition Of Cold-Sprayed Ti2alc Coating

Effects of Hydrogen on the Interfacial Reaction Between Ti 6al 4V Alloy Melt and Al2O3 Ceramic Shell

Morphology "Phase Diagram" Of The Hydrous Alumina Coating On Tio2 Particles During Aqueous Precipitation

Effect of Hf Addition on Initial Microstructure of (ni, Pt)Al Coating and Inhibiting the Detrimental Sulfur During High Temperature Exposure at 1150 °C