Modeling of Heat Transfer and Solidification Process of Spray Formed Billet

FY Cao,CS Cui,QC Li

2009-01-01

Abstract:In this paper, modeling of heat transfer and solidification process of spray formed billet was established. Thermal profiles of billet at various spray time and under various spray forming conditions were calculated numerically. The simulation results are consistent with the actual experimental results.

What problem does this paper attempt to address?

Modeling of Heat Transfer and Solidification of Composite Roll

CS Cui,FY Cao,ZY Li,QC Li

2009-01-01

Journal of Material Science and Technology

Abstract:Modeling of heat transfer and solidification of composite roll was established and used to predict the thermal history and solidification process of roll during spray forming. Evolution of temperature field of the preform and cooling rate in the growing deposit during spray deposition and post-deposition were numerically simulated.
Shape modeling of spray formed columnar billets

Fuyang Cao,Peijie Li,Hongbo Fan,Chengsong Cui,Qingchun Li

2003-01-01

Abstract:Shape modeling of spray formed billets was established through tracing surface coordinates of the billets. Not only is the influence of the position change of any point on a billet surface on the deposited effect considered, but also the influence of the temperature of the point and the positions of other points on the billet surface on the deposited effect was respected. Billet surface coordinates are calculated according to the real process of spray forming strictly, shapes of spray formed billets can be computed at any spray time and under any spray condition, and the shape modeling was confirmed. The shape modeling in this paper is utilized to predict the geometry of the preform under various spray forming processing conditions. 2024 is used as the spray forming material.
Three-Dimensional Mathematical Shape Model and Process Research of Spray-Formed Billet

Yuan Hao,Fan Junfei,Ren Sanbing,Wang Haowei,Zhang Yijie

DOI: https://doi.org/10.3724/sp.j.1037.2013.00320

IF: 1.797

2013-01-01

ACTA METALLURGICA SINICA

Abstract:Spray forming is an advanced technology that is used to produce a variety of high-performance materials with the characteristics of rapid solidification. By properly controlling of spray forming parameters, it is possible to fabricate near-net-shaped preforms, such as rod-billets, strips, and tubes. During the billet spray forming process, the shape of deposit strongly influences the solidification and consequently end-product quality. Therefore, it is necessary to reveal the shape forming mechanism in spray forming process. In the present work, a three-dimensional (3D) model, tracing the coordinates of the moving surface of a growing spray-formed billet, has been formulated to predict the shape evolution of the general deposit. This geometric model takes into account geometrical process parameters in the whole spray forming process: mass flux and mass distribution, position of the atomizer, distance between atomizer and the preform, substrate withdrawal velocity and rotation speed. This makes it possible to model not only the growth of a Gaussian shaped deposit in which case the spray axis and the rotation axis coincide, but also the profile evolution as there is a spray angle between these two axes. For this purpose, "shadowing effect" must be taken into account as a core part of the surface evolution algorithm. On the basis of this 3D model, a timesaving and accurate methodology is established to determine the shadowing effect coefficient, using the "triangular element checking" algorithm coupled with back face culling (BFC). The transient shape modeling has been validated by numerical algorithms and experimental investigation, and has proved that the simulated billet profiles are in good agreement with the experimental data. The effect of spray forming parameters, such as spray distribution parameters, withdrawal velocity, initial eccentric distance, spray angle and angular velocity of rotation, are analyzed. According to the obtained simulation results, the most dominant parameters affecting the shape evolution of deposit are the spray distribution parameters, withdrawal velocity, and initial eccentric distance. It is also found that the spray angle mainly affects the profile of the top transition region of the rod. The effect of the angular velocities of substrate on the shape evolution of the deposit is not significant. Finally, the maximum withdrawal velocity and maximum initial eccentric distance are deduced based on the analysis of shape form mechanism, which can be used to guide the process optimization during spray forming.
Applying of Real-time Heat Transfer and Solidification Model on the Dynamic Control System of Billet Continuous Casting

Jiaocheng Ma,Zhi Xie,Guanglin Jia

DOI: https://doi.org/10.2355/isijinternational.48.1722

2008-01-01

ISIJ International

Abstract:In this paper, a real-time mathematical heat transfer model for billet continuous casting of low carbon steel has been presented and solved by finite volume method. This model can be used to simulate the casting conditions which vary frequently. As taking the variation of superheat of liquid steel into consideration in the water flow rate distribution, the fluctuation of billet surface temperature has been decreased. Meanwhile the fluctuation of measured temperature has been largely reduced when it is measured with thermal imager. The mathematical model has been validated by measuring shell thickness and surface temperature in industrial caster. The on-line model can monitor surface temperature and shell thickness along the caster machine in the casting process, and it has been applied on the dynamic control system to adjust the operation parameters. The billet defect has been decreased greatly and the quality of billet has been obviously improved.

metallurgy & metallurgical engineering
Thermomechanical Modeling of Solidification Process of Squeeze Casting Ii. Numerical Simulation and Experimental Validation

Zhu Wei,Han Zhiqiang,Liu Baicheng

IF: 1.797

2009-01-01

ACTA METALLURGICA SINICA

Abstract:Based on the thermomechanical model and solution methodology described in Part I, a finite element program for simulating the solidification process of squeeze casting was developed. By using the program and a constitutive relationship based on Gleeble test data, the solidification processes of A356 aluminum alloy under different process parameters were simulated. Squeeze casting experiments were carried out for validating the developed model and program. It is shown that the results of numerical simulation are in good agreement with the experimental results.
Numerical Study of Heat Transfer and Solidification Behavior of Gas-Atomized Fe-6.5% Si (mass Fraction) Droplets

Ke-Feng Li,Yun-Hu Zhang,Chang-Jiang Song,Qi-Jie Zhai

DOI: https://doi.org/10.1007/s40436-016-0141-x

2016-01-01

Abstract:During spray atomization process, the heat transfer and solidification of droplets play very important roles for the deposition quality. Due to the difficulties of experimental approach, a numerical model is developed, which integrates liquid undercooling, nucleation recalescence and post-recalescence growth to present the full solidification process of Fe-6.5% Si (mass fraction) droplet. The droplet velocity, temperature, cooling rate as well as solid fraction profiles are simulated for droplets with different sizes to demonstrate the critical role of the size effect during the solidification process of droplets. The relationship between the simulated cooling rate and the experimentally obtained secondary dendrite arm spacing is in excellent agreement with the well-established formula. The pre-constant and exponent values lie in the range of various rapid solidified Fe-based alloys reported, which indicates the validity of the numerical model.
Flow Behavior and Heat Transfer of Atomizing Gas and Metal Droplets in Spray Forming Process

Chengsong Cui,Jun Shen,Daming Xu,Qingchun Li

DOI: https://doi.org/10.1115/imece1996-1052

1996-01-01

Abstract:Abstract The dynamics for the fluid flow and heat transfer in spray forming process is theoretically analyzed and the controlling equations of the flow and heat transfer are derived. The shape/geometry and the solidification profiles such as temperature and remained liquid in the preform are calculated by the simulation of the controlling equations. The predicted cooling rates at different positions can reach 102−103 °C /s at the beginning of deposition and decrease to 100∼101 °C/s in the subsequent cooling process. The characteristics of rapid solidification structures with spray forming are mainly due to the high cooling rate of droplets during spray process (>104 °C /s) and breaking mechanism of dendrite on deposition.
Continuous Casting Mould for Square Steel Billet Optimised by Solidification Shrinkage Simulation

T. M. Wang,S. W. Cai,J. Xu,Y. Y. Du,J. Zhu,J. J. Xu,T. J. Li

DOI: https://doi.org/10.1179/030192310x12683045806026

IF: 1.7031

2010-01-01

Ironmaking & Steelmaking

Abstract:A transient, thermoelastic–viscoplastic finite element model has been applied using ANSYS to study the thermal and mechanical behaviour of the solidifying shell during continuous casting of steels. In the model, a gap dependent heat transfer condition was imposed in the boundary between shell and mould. Thermophysical properties (e.g. thermal linear expansion) depending on temperature and composition were derived from experiment data and empirical correlations. Continuous casting of square billets with different steel grades, B72LX and ER70S6, were simulated to investigate the evolution of shell temperature, stress and shrinkage with an indirect coupled approach. The results indicated that carbon content, pouring temperature and casting speed have obvious influence on shrinkage of billets. According to shrinkage compensating principle, the mould taper and inner cavity geometry were designed and optimised based on average shrinkage histories of the solidifying shell. The new design has performed well in industrial trials.
Simulation and application of dynamic heat transfer model for improvement of continuous casting process

J. C.,Z. Xie,Y. Ci,G. L. Jia,J. C. Ma

DOI: https://doi.org/10.1179/174328408x339107

IF: 1.8

2009-05-01

Materials Science and Technology

Abstract:Numerical simulation is being increasingly used to improve the existing cooling systems. In order to attain highest quality strand, a two-dimensional dynamic mathematical heat transfer model of billet continuous casting of low carbon steel has been presented. This model can be used to compute the billet temperature distribution and shell thickness, especially it can be used to simulate the solidification process which is caused by frequently variational casting conditions. The fluctuation of measured temperature has been reduced to <10°C with thermal imaging system. The online model can monitor surface temperature and shell thickness in the casting process. So it provides the possibility for the online process control. For the validation of the dynamic model, a lot of billet surface temperature and shell thickness measurement were carried out on an actual casting machine. Finally, the dynamic model has been used for adjusting the operating parameters to improve the casting speed.

materials science, multidisciplinary,metallurgy & metallurgical engineering
Modeling and Simulation of Porosity in Spray Deposition

Mingxiang Liu,Zhenshan Cui,Yangqi Li

DOI: https://doi.org/10.1007/s11663-019-01609-w

2019-01-01

Abstract:Numerical models, consisting of interstitial porosity model and gas porosity model, have been developed to predict the porosity in the spray deposition process. The interstitial porosity model is based on the assumption of liquid feeding in the porous mushy layer of the deposit. The porosity fraction is related to the particle packing density and the amount of the feeding flow during solidification. The gas porosity model is based on the diffusion kinetics of gas pore formation. A numerical simulation of spray deposition for a billet was carried out by coupling the porosity model with the shape and heat-transfer models. The volume fraction and distribution of the porosity were investigated. As a result of the experimental verification, the simulation results showed good agreement with the experimental data. As applications, the models were used to investigate the influence of spray process parameters on porosity formation. The investigation demonstrated that the porosity is substantially influenced by the temperature of the impinging layer and the preheating of the substrate.
Numerical Simulation of Solidification and Heat Transfer in Continuously Cast Bloom

GAO Wen-jiang,ZHAO Ke-wen,SHEN Hou-fa

DOI: https://doi.org/10.3969/j.issn.1001-3814.2006.17.026

2006-01-01

Abstract:A mathematical heat transfer model to describe the solidification process of continuously cast bloom has been developed. The liquidus and solidus in the mushy zone was calculated based on back diffusion and a database for multi-component steel with the thermal-physical parameters depended on composition, temperature and solid fraction. Three-dimensional temperature distribution and solid fraction in a bloom were predicted with complicated boundary heat transfer conditions which involve real nozzle spray flux and individual roll contact in the secondary cooling region of the caster. The calculated results agree well with measured values.
Numerical Simulation and Experiments Research on Secondary Cooling Process of Thick Slab Continuous Casting

TIAN Yong,SHEN Houfa,YU Gongli,WANG Rengui,LI Zelin

DOI: https://doi.org/10.3969/j.issn.1005-4006.2007.05.001

2007-01-01

Abstract:Based on fundamental theory of solidification and heat transfer,the three-dimensional steady solidification-heat transfer mathematical model describing continuous casting process of slab was found.The model considered the influence of thermal -physical parameters such as components,solid fraction and temperature and used solute transfer and back diffusion theory to deduce the liquidus and solidus in mushy zone.The slab continuous caster in the No.1 Steelmaking Plant of Anshan Steel Co.,Ltd.was simulated.Three-dimensional temperature and solid fraction distribution was predicted with boundary conditions including the real nozzle spray flux and the roll contact with slab.The simulation results were agreement with data of measurements of surface temperature and solidified shell thickness of slab in various segments of secondary cooling zone.
Analysis and Optimization of Spray Nozzles Arrangement in Slab Casting by Numerical Simulation

SUN Meng,WANG Ye-ting,SHEN Hou-fa

DOI: https://doi.org/10.13228/j.boyuan.issn1001-0963.2011.04.012

2011-01-01

Abstract:The arrangement of spray nozzles has an important impact on the cooling of slab.A three-dimensional steady heat transfer and solidification model was used to analyze the cooling of slab with different spray nozzles arrangements.By modification of the spray nozzles arrangement,the two hot spots as like "glass shape" in the slab cross section was prevented,and the cooling condition of slab was improved.The simulation results match well with the real process,which indicates the reliability and practicability of the model.
Analysis of Spray Forming and Processing Factors of Superalloy Billets

康福伟,孙剑飞,沈军,李庆春

DOI: https://doi.org/10.3969/j.issn.1006-2793.2004.02.019

2004-01-01

Abstract:Spray forming is a novel rapid solidification technique which is suited to prepare superalloy turbine disk billets. Superalloy billets prepared by the process feature fine and homogeneous microstructure. The process tends to eliminate macrosegreation and improve hot work ability and performance. The processing characteristics and advantages were presented. The influence factors were investigated, and further trend pointed.
Numerical simulation of nucleation, solidification, and microstructure formation in thermal spraying

H. Zhang,X.Y. Wang,L.L. Zheng,S. Sampath

DOI: https://doi.org/10.1016/j.ijheatmasstransfer.2003.11.030

IF: 5.2

2004-01-01

International Journal of Heat and Mass Transfer

Abstract:A splat formation model has been developed based on the classic nucleation theory accounting for heterogeneous nucleation kinetic and crystal growth to predict the nucleation temperature and grain size distribution. The predicted grain size distribution has been compared with experimental data for molybdenum (Mo) splats on different substrates. The influence of the substrate material, interfacial thermal contact resistance, and wettability on the nucleation, grain size distribution, and rapid solidification process has been investigated. Based on scaling analysis, the nucleation delay and solidification times have been derived and compared with simulation results.
Study on solidification and heat transfer of billet shell in a new-structure high-speed continuous casting mold

Di Wang,Changchuan Xie,Fushuai Li,Tianyu Wu,Aimin Zhao

DOI: https://doi.org/10.1016/j.jmrt.2024.10.011

IF: 6.267

2024-10-10

Journal of Materials Research and Technology

Abstract:In this work, a three-dimensional finite element model of a newly structured high-speed continuous casting mold was established to study the heat transfer and solidification process of the billet shell. A complete billet shell, from the meniscus to the secondary cooling zone, was obtained through flame cutting. Using both simulations and test verification, detailed analyses were conducted on the temperature field distribution, thickness variation law, and cooling rate law of the billet shell within the mold, revealing its solidification behavior. Additionally, the effects of casting speed, molten steel superheat, and mold taper on the solidification behavior of the billet shell were discussed. Results showed that the simulation data were basically consistent with the test verification results. Within 200 mm from the meniscus, the heat dissipation accounted for three-quarters of the mold's total heat dissipation. The cooling rate at the corners of the billet shell was slightly higher than that at the sides. Between 200 mm and 400 mm from the meniscus, air gaps caused the temperature at the corners of the billet shell to rise. Afterwards, the whole billet shell eventually reached a similar the heat dissipation rates. The thickness of the billet shell increased exponentially within 110 mm from the curved meniscus, and from 110 mm to the exit of the mold, the thickness increased linearly but slowly. The effect of molten steel superheat within a range of 10 °C on billet shell solidification was relatively minor. Increasing the casting speed reduced the billet shell thickness and raised the billet shell surface temperature. However, increasing the taper of the mold had the opposite effect. Both adjustments shifted the gap formation position backward.

materials science, multidisciplinary,metallurgy & metallurgical engineering
Application of Modeling and Simulation of Thermal Stress in Solidification Process of a Heavy Steel Casting

Xiaogang Liu,Jinwu Kang,Tianyou Huang,Baicheng Liu

DOI: https://doi.org/10.3321/j.issn:1004-132X.2006.19.013

2006-01-01

Abstract:The thermal stress evolution during the solidification process of a Francis turbine band casting had been simulated by the FDM/FEM integrated system. The interaction between the casting and core was disposed by using the contact element method in numerical simulation, which improved traditional method for disposing casting/model boundary conditions. The tendency of hot tearing during solidification and cold crack during cooling was predicted by employing different criteria based on the simulated stress results. The characteristics of deformation during cooling were also studied, which provided reference to control the shrinkage scale of the casting. The simulated results are approximately in accordance with the practical case.
Numerical Simulation of Solidification Process on Single Crystal Ni-Based Superalloy Investment Castings

Jing Yu,Qingyan Xu,Kai Cui,Baicheng Liu,Akihiko Kimatsuka,Asunori Kuroki,Atsushi Hirata

2009-01-01

Journal of Material Science and Technology

Abstract:Bridgman directional solidification of investment castings is a key technology for the production of reliable and highly efficient gas turbine blades. In this paper, a mathematical model for three-dimensional (M) simulation of solidification process of single crystal investment castings was developed based on basic heat transfer equations. Complex heat radiation among the multiple blade castings and the furnace wall was considered in the model. Temperature distribution and temperature gradient in superalloy investment castings of single blade and multiple ones were investigated, respectively. The calculated cooling curves were compared with the experimental results and agreed well with the latter. It is indicated that the unsymmetrical temperature distribution and curved liquid-solid interface caused by the circle distribution of multiple turbine blades are probably main reasons why the stray grain and other casting defects occur in the turbine blade.
Theoretical Analysis of the Solidification of Aluminum Alloy Billet in Air-Slip DC Mold

于赟,马乃恒,许振明,李建国

2004-01-01

Abstract:Based on the heat transfer analysis of Air-Slip DC mold, a numerical model was presented to study the quantitative relationships between critical solidification layer and casting rate, pouring temperature and mold cooling ability etc. The analytical results show that the Air-Slip mold heat transfer condition plays important roles on choices of a casting rate and the pouring temperature, and that the product of billet diameter and casting rate is a certain constant under a certain condition of the mold.
Numerical simulation and optimization of steel tube billet heating process in rotary hearth furnace using CFD

Likun Yang,Fuyong Su,Zhi Wen,Shuming Tao,Guangjie Bai,Chunmei Luan

DOI: https://doi.org/10.2298/tsci220621060y

IF: 1.971

2023-01-01

Thermal Science

Abstract:Billet reheating is an important part of the steel production process. Since the production process will adopt different tube billet arrangement strategies, and the condition of the furnace hearth will also change due to long-term operation and accumulation of iron oxide scales, these factors will inevitably affect heating efficiency and temperature distribution uniformity of the tube billet, thereby affecting the quality of the final product. In this study, a physical and mathematical model was established for a 48m-diameter rotary hearth furnace (RHF) of the seamless steel pipe production line and typical 300mm-diameter tube billets of different lengths. Commercial Fluent code was used to carry out Computational Fluid Dynamics (CFD) numerical simulation research on the influence of the above factors. Optimizing and adjusting strategies under different arrangement strategies were proposed, and the influence of furnace hearth condition change on heating effect was studied. The methods and simulation approach of this paper also have guidance for the billet heating control in similar continuous heating furnaces.

thermodynamics

Modeling of Heat Transfer and Solidification Process of Spray Formed Billet

Modeling of Heat Transfer and Solidification of Composite Roll

Shape modeling of spray formed columnar billets

Three-Dimensional Mathematical Shape Model and Process Research of Spray-Formed Billet

Applying of Real-time Heat Transfer and Solidification Model on the Dynamic Control System of Billet Continuous Casting

Thermomechanical Modeling of Solidification Process of Squeeze Casting Ii. Numerical Simulation and Experimental Validation

Numerical Study of Heat Transfer and Solidification Behavior of Gas-Atomized Fe-6.5% Si (mass Fraction) Droplets

Flow Behavior and Heat Transfer of Atomizing Gas and Metal Droplets in Spray Forming Process

Continuous Casting Mould for Square Steel Billet Optimised by Solidification Shrinkage Simulation

Simulation and application of dynamic heat transfer model for improvement of continuous casting process

Modeling and Simulation of Porosity in Spray Deposition

Numerical Simulation of Solidification and Heat Transfer in Continuously Cast Bloom

Numerical Simulation and Experiments Research on Secondary Cooling Process of Thick Slab Continuous Casting

Analysis and Optimization of Spray Nozzles Arrangement in Slab Casting by Numerical Simulation

Analysis of Spray Forming and Processing Factors of Superalloy Billets

Numerical simulation of nucleation, solidification, and microstructure formation in thermal spraying

Study on solidification and heat transfer of billet shell in a new-structure high-speed continuous casting mold

Application of Modeling and Simulation of Thermal Stress in Solidification Process of a Heavy Steel Casting

Numerical Simulation of Solidification Process on Single Crystal Ni-Based Superalloy Investment Castings

Theoretical Analysis of the Solidification of Aluminum Alloy Billet in Air-Slip DC Mold

Numerical simulation and optimization of steel tube billet heating process in rotary hearth furnace using CFD