Photoconductive polyimides based on bisphenyl-porphyrin II: structure and photoconductive properties of polyimide and their precursor films

Baoku Zhu,Zhikang Xu,Zhenmei Liu,Youyi Xu

2000-01-01

Abstract:Three series of bisphenylporphyrin (BPP) containing polyamic acids (PAAs) and polyimides were synthesized. The structures and photoconductive properties of spinning and Langmuir-Blodgett (LB) films of these BPPs were determined.

What problem does this paper attempt to address?

Photoconductive Polyimides Based On Bisphenyl-Porphyrin I: Synthesis And Characterization.

Baoku Zhu,Zhikang Xu,Youyi Xu

2000-01-01

Abstract:Three series of polyamic acids (PAAs) containing 5,15-bisphenylporphyrin (BPP) moieties were synthesized and converted to corresponding polyimides (PIs) by heat and chemical treatment. The obtained PIs were characterized by UV-vis measurement and spectroscopy techniques.
Synthesis and photoconductive characteristics of biphenylporphyrin-containing poly(amic acid)s and polyimides

Bao Ku Zhu,You Yi Xu,Xiu Zhen Wei,Zhi Kang Xu

DOI: https://doi.org/10.1002/pi.1402

IF: 3.213

2004-01-01

Polymer International

Abstract:Three series of biphenylporphyrin (BPP) -containing poly(amic acid)s (PAAs) were synthesized and converted into heat-treated polyimides (HPIs) and chemically treated polyimides (CPls). Viscosity measurements, UV-vis and IR spectroscopies, as well as thermogravimetric analysis (TGA), were used to characterize the structures of the polymers. UV-vis spectra revealed that the BPP units formed aggregates in PAA and CPI films, rather than in HPI films. Photoinduced discharge was used to characterize the photoconductive properties of these polymer films. It was found that the photosensitivity was greatly enhanced by introducing BPP units into the polymer chains. For these three series of polymers, the photosensitivity increased in the order PAA < HPI < CPI according to the content of BPP in the polymers. The photoconductive characteristics were interpreted by the intrinsic pi - pi* process of BPP aggregation and the extrinsic process of charge-transfer complex formation. The best photoconductive performances of the CPls were attributed to the existence of two charge-carrier-generation processes. (C) 2004 Society of Chemical Industry.
Photoconductive polyimide (3). Preparation and photoconductivity of polyimide LB films containing carbazole and copper-phthalocyanine groups

Youyi Xu,YuanSheng Chen,Zhikang Xu

1997-01-01

Abstract:Polyimide Langmuir-Blodgett films containing carbazole and copper-phthalocyanine groups were prepared by using a precursor method. It is found that the photoreceptors fabricated by the polyimide LB films show more excellent photoconductivity.
Photoconductivity of Copolyimide Films Containing Tetraphenylporphyrin and Carbazole Moieties

Zhi-Kang Xu,Bao-Ku Zhu,You-Yi Xu

DOI: https://doi.org/10.1021/cm970738o

IF: 10.508

1998-01-01

Chemistry of Materials

Abstract:A series of polyimide copolymers based, on pyromellitic dianhydride, 3,6-diaminocarbazole, and terta(4-aminophenyl)porphyrin were synthesized. The "precursors", copolyamic acids, and the copolyimides were characterized by IR, UV-visible, and emission spectra and thermogravimetry. The mole ratios of tetraphenylporphyrin (TPP) to carbazole (Cz)in the polymers calculated from the UV-visible spectra indicate that TPP and Ct were incorporated into the polymer backbones as expected. The copolyimide films were fabricated into bilayer photoreceptors as a charge-generating layer to investigate their photoconductivity. It was found that the photosensitivity of the copolyimides increases with the incorporation of TPP into the polymer chains. These results were compared with those of the tetraphenylporphyrin-doped pyromellitic/3,6-diaminocarbazole polyimide film and explained on the basis of charge-transfer complex formation.
Synthesis and electrophotographic properties of copolyimides containing tetraphenylporphyrin

Bao-Ku Zhu,Zhi-Kang Xu,You-Yi Xu

DOI: https://doi.org/10.1016/S0014-3057(98)00082-2

IF: 6

1999-01-01

European Polymer Journal

Abstract:A series of polyimide copolymers based on pyromellitic dianhydride, oxydianiline (ODA) and terta(4-aminophenyl)porphyrin were synthesized. The ‘precursors’, copolyamic acids and the copolyimides, were characterised by UV–visible spectra, IR spectra and thermogravimetry. The mole ratios of tetraphenylporphyrin (TPP) to diphenylether in the polymers calculated from the UV–visible spectra indicate that TPP and ODA were incorporated into the polymer backbones as expected. To investigate the photoconductivity of the copolyimides (CPIs), three and four-layered photoreceptors containing the CPI films as charge-generating layers were fabricated. It was found that the photosensitivity of the CPIs increased with the incorporation of TPP into the polymer chains. These results were compared with those of tetraphenyl-porphyrin doped pyromellitic/oxydianiline (PMDA/ODA) polyimide and explained on the basis of the formation of charge-transfer complexes.
Enhancing The Photoconductivity Of Polyimides By Incorporating Intrinsic Chromophore Units

Bao-Ku Zhu,You-Yi Xu,Zhi-Kang Xu

DOI: https://doi.org/10.1201/b12194-25

2005-01-01

Abstract:The formation of charge-transfer complexes (CTCs) between the electron-rich rings and imide units inter- or intra-molecularly generates only a weak photoconductivity in aromatic polyimides (PIs). Unlike the intrinsic photoconductivity of organic materials, in which the free charge carriers are generated from excitation of chromophores and transfer among the chromophores, the photoconductivity originating from the CTCs in the PIs is of extrinsic nature. As the extrinsic photoconductivity in classic aromatic PIs without chromophore is too low for application in practical photoconductor devices, in this study porphyrin rings were incorporated into the PI backbone as chromophore units to enhance its photoconductivity. The photo-induced discharge measurements on photoreceptors in which polyimide films were used as charge carrier generating layers were adopted to characterize the photoconductivity of phorphyrin containing PI. It was shown that the photosensitivity of these porphyrin-containing PI films was greatly improved in comparison to chromophore-free polyimides. Also, it was found that the chemically imidized PI films had a higher photosensitivity than the thermally imidized ones. The enhancement in photoconduction resulted not only from the intrinsic photoconduction process of porphyrin chromophores, but also from the extrinsic photoconduction of CTCs using porphyrin units as electron donors. When the porphyrin containing PI was fabricated into an ordered film by the Langmuir-Blodgett (LB) process, its photosensitivity was further improved. Furthermore, the aggregation or dispersion of porphyrin units in PI films varied with the fabrication and imidization process of the films, and thus influenced the photoconduction processes and the performance greatly. Besides the porphyrin-containing PI films, their precursor films, including poly(amic acid) spin-coated films and tertiary amine poly(amic acid) salts LB films, were also investigated to reveal the actual photoconduction process of chromophore-containing polymers.
A study of photoconductive polyimides(I) - Synthesis, characterization and the photoconductivity study of polymers containing carbazole and phthalocyanine groups

YuanSheng Chen,Zhikang Xu,Baoku Zhu,Youyi Xu

1997-01-01

Abstract:Polyamic acid with carbazole and copper-phthalocyanine was synthesized by condensation polymerization. Heat resistant polyimide was obtained by thermal treatment of the polyamic acid. It was found that the initial degradation temperature of the polyimide was more than 530 ��C and it was confirmed by IR analysis that the polyamic acid was completely converted to polyimide after the heat treatment process. The photoconductivity of the P/R system has been improved by the incorporation of phthalocyanine group into the polyimide main chain.
A study of photoconductive polyimides .1. Synthesis, characterization and the photoconductivity study of polymers containing carbazole and phthalocyanine groups

YS Chen,ZK Xu,BK Zhu,YY Xu

1997-01-01

Abstract:Polyamic acid with carbazole and copper-phthalocyanine was synthesized by condensation polymerization, Heat resistant polyimide was obtained by thermal treatment of the polyamic acid, It was found that the initial degradation temperature of the polyimide was more than 530 degrees C and it was confirmed by IR analysis that the polyamic acid was completely converted to polyimide after the heat treatment process, The photoconductivity of the P/R system has been improved by the incorporation of phthalocyanine group into the polyimide main chain.
Study on Photoconduction Properties of Polyimide Films Containing Tetraphenylporphyrin Units

朱宝库,徐又一,徐志康

DOI: https://doi.org/10.3969/j.issn.1008-9357.2003.02.004

2003-01-01

Abstract:Two series of polyimide (PI) copolymer films which contained tetraphenylporphyrin (TPP) /diphenyl ether (DPE) units, and TPP/carbazole (Cz) units were respectively fabricated into photoreceptors (PR) as charge-carrier-generating layers (CGL) to investigate their photocondutivities by photoinduced discharge (PID) measurements. It was found that the photocondutivities of these two series PI films increased with the increasing of copolymerized TPP unit. TPP/ DPE unit containing PI films demonstrated better photoconduction than TPP/Cz units contained series when the content of TPP unit was comparable. The photoconduction of TPP unit copolymerized PI films was obviously better than that of tetraphenylporphyrin molecule doped PI films. The charge-barrier-layer of PMMA in PR did could positively effect the photoconduction embodiments. The observations were interpreted on the basis of inherent and non-inherent photoconduction mechanism.
Photoelectrical Properties of Polyaniline/polyimide Complex Thin Film

JB Zheng,CQ Hou,J Liu,J Ren,JL Zhao

DOI: https://doi.org/10.1117/12.674201

2006-01-01

Abstract:Using pyromellitic dianhydride (PMDA) and bis(4-aminophenyl) ether (ODA) as monomer materials, the polyamic acid (PAA), a precursor of polyimide (PI), was synthesized. PAn was doped and modified with the polyamic acid by solution mixing method, and the modified PAn/PAA blend with good solubility and forming-film was obtained. Then uniform PAn/PI complex thin film with good forming-film and thermo-stability can be prepared by solvent casting and followed by thermal imidization process at the temperature of 150oC-250oC for 60 min. Conductance experiments showed the surface conductivity of PAn/PI thin films can raise to 10-5S from 10-10S and change with the increase of the content of PAA. IR and UV-vis spectra showed that it has a chemical doping reaction between PAn and PAA during mixing, and the absorption of PAn/PI complex films in UV-vis region appears red shift and the peak shape becomes broad. The degenerate four-wave mixing experimental results showed that the third-order optical nonlinear susceptibility χ(3) of PAn/PI thin films can be markedly enhanced and the maximum χ(3) can reach 8.85×10-10esu, which presents good third-order nonlinear property.
Synthesis And Characterization Of Porous Polyimide Films Containing Benzimidazole Moieties

Jianwei Li,Guangcheng Zhang,Zhanxin Jing,Jiantong Li,Lisheng Zhou,Hongming Zhang

DOI: https://doi.org/10.1177/0954008317697803

IF: 1.73

2017-01-01

High Performance Polymers

Abstract:In this study, a series of porous polyimide films containing benzimidazole units were prepared through a phase separation process. The dibutyl phthalate was selected as porogen. The copolyimides were prepared by the reaction of 3,3,4,4-benzophenonetetracarboxylic dianhydride with two diamines of 2-(4-aminophenyl)-5-aminobenzimidazole (BIA) and 4,4-diaminodiphenyl ether with various molar ratios. The resultant porous polyimide films exhibit optimum cell-size distributions. The effects of BIA on morphology, mechanical, and thermal properties of the porous films were explored. It was found that as the BIA content reached up to 30 mol%, the porous copolyimide film demonstrates remarkable thermal stability and admirable mechanical properties with the glass transition temperature of 294 degrees C, 5% weight loss temperature in argon flow up to 545 degrees C, and a tensile strength of 48 MPa. The incorporation of BIA into the polyimide chains brought the highly rigid structures and strong intermolecular interactions, resulting in the enhancement in the thermal stability and the mechanical properties.
Solubility, Thermal and Photoluminescence Properties of Triphenyl Imidazole-Containing Polyimides.

Wu Bai,Zhizhi Hu,Yunhua Lu,Guoyong Xiao,Hongbin Zhao,Jianmin Zhu,Zhaobin Liu

DOI: https://doi.org/10.1039/d1ra02765d

IF: 4.036

2021-01-01

RSC Advances

Abstract:In this paper, three kinds of triphenyl imidazole-containing diamines including 2-phenyl-4,5-bis(4-(4-amino-2-trifluoromethylphenoxy)phenyl)imidazole (PBAI), 2-(4-methylphenyl)-4,5-bis(4-(4-amino-2-trifluoromethyl phenoxy)phenyl)imidazole (MPBAI) and 2-(4-trifluoromethylphenyl)-4,5-bis(4-(4-amino-2-trifluoromethylphenoxy)phenyl)imidazole (TFPBAI) were synthesized. Then, a series of polyimide (PI) films were prepared by the solution polymerization of the three diamines and various dianhydrides, such as 4,4'-(hexafluoroisopropylidene)diphthalic anhydride (6FDA), 1,2,4,5-pyromellitic dianhydride (PMDA) and 1,2,3,4-cyclobutanetetracarboxylic dianhydride (CBDA), followed by thermal imidization. The effects of chemical structures on the solubilities and thermal, optical and electrochemical properties of polyimides were explored. All the polyimides exhibited higher glass transition temperatures around 300 °C and excellent solubilities in common polar solvents. The polyimide films derived from CBDA or 6FDA showed better optical properties with light color and transparent characteristics. The fluorescence test showed that the photoluminescence color of CBDA-based polyimide films is in the blue range in the CIE 1931 spectrum, while the polyimide film based on PMDA and 6FDA presented black or weak yellow light. However, all these polyimides in solution exhibited similar blue luminescence. Electrochemical tests indicated that the HOMO and LUMO values of these films were around -6.5 and -3.6 eV, and the energy gap difference was about 3.0 eV. Therefore, the triphenyl imidazole-containing polyimides exhibit comprehensive performance, which will be expected as a new kind of functional material for certain application in the optical and optoelectronics fields.
Optical and Electrical Properties of Cu-Phthalocyanine-doped Polyimide Thin Films by Vapor Deposition Polymerization

ZHENG Jian-bang,WANG Yuan,REN Ju,HOU Chao-qi

DOI: https://doi.org/10.3969/j.issn.1001-5868.2005.04.019

2005-01-01

Abstract:Using Cu-phthalocyanine (CuPc), 4,4'-diaminodiphenyl ether and pyromellitic dianhydride as monomer materials, polyimide(PI) thin films doped-CuPc have been prepared onto glass substrate by vapor phase co-deposition polymerization under a vacuum of 2 × 10-3 Pa and thermal curing of polyamic acid film in at temperature of 150-200 C for 60 min. In this process, the polymerization can be carried out through controlling the stoichiometric ratio, heating time and deposition rates of the three monomers. IR spectrum identifies the designed chemical structure of the polymer. The absorption of polyimide doped-CuPc is very intense in vis-range and near-infrared by UV-Vis spectrum. And, the PI films doped-CuPc polymerized by vapor phase deposition have uniformity, fine thermal stability and good nonlinear optical properties, and the third-order optical nonlinear susceptibility x(2) with degenerate four-wave mixing can be 1. 984 × 10-9 ESU.
Preparation and Properties of Polyimides Based on Bis[3,5-Dimethyl-4-(4-Aminophenoxy)Phenyl]Methane

Yuan,Bao-Ping Lin,Yue-Ming Sun

DOI: https://doi.org/10.1002/app.25750

IF: 3

2007-01-01

Journal of Applied Polymer Science

Abstract:A series of polyimide (PI) thin films were synthesized based on bis[3,5-dimethyl-4-(4-aminophenoxy)phenyllmethane and conventional aromatic dianhydrides. The structures and properties of the thin films were measured with Fourier transform infrared, NMR, thermogravimetric analysis, dynamic mechanical analysis, and impedance analysis. The PI films exhibited glass-transition temperatures in the range of 211-300 degrees C and possessed initial thermal decomposition temperature reaching up to 457-482 degrees C in air and 461-473 degrees C in nitrogen. Some PI films had high solubility in organic solvents such as 1-methyl-2-pyrrolidinone, NN-dimethylformamide, N,N-dimethylacetamide, dimethyl sulfoxide, m-cresol, tetrahydrofuran, and CHCl3. The mechanical properties of these films were also examined. The dielectric constants of the films were in the range of 2.8-3.3 at 25 degrees C. (c) 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 1265-1270, 2007.
Synthesis and Characterization of Biphenyl Polyimide Containing Alkyl Sulfide Structure

张艺,郑雪菲,牛新星,张燕珠,肖善雄,林文璇,刘四委,黄爱萍,池振国,许家瑞

2010-01-01

Abstract:A novel polyimide containing alkyl sulphide structure was synthesized through polymerization of 4,4'-diamino diphenyl sulphide(SDA) and 3,3′,4,4′-biphenyl-tetracarboxylic acid dianhydride(BPDA) by thermal imidization and chemical imidization.A real-time online tracing method was built up by using the advanced rheology expanded systems(ARES),as well as the effects of reaction conditions to the thermal and chemical imidization by thermogravimetic analysis,which provided more efficient methods for preparing high performance polyimide.The structures and properties of the polyimide were characterized by fourier transform infrared spectroscopy(FTIR),small angle laser light scattering(SALS),contact angle analysis and differential scanning calorimetry(DSC) etc.The results showed that the surface properties of polyimide films were great improved by introducing the alkyl sulphide structure into the main chain of polyimide,which exhibited similar surface tension with copper foil,and higher adhesion work between the new polyimide and copper foil than the traditional one.The absolute weight-average molecular weight of the polyimide was determined to be(3.8±1.1)×104 g/mol;the decomposition temperature was higher than 560 ℃.The DSC results showed that the polyimides by both thermal and chemical imidization were with high glass transition temperature.In comparison,chemical imidization was beneficial to getting high degree of imidization,resulting in higher glass transition temperature.
Synthesis and Characterization of New Types of Perylene Bisimide‐Containing Conjugated Copolymers

XR He,HB Liu,N Wang,XC Ai,S Wang,YL Li,CS Huang,S Cui,YJ Li,DB Zhu

DOI: https://doi.org/10.1002/marc.200400660

IF: 5.006

2005-01-01

Macromolecular Rapid Communications

Abstract:Two new poly(perylene bisimide) polymers that contain biphenyl (PPery) and anthracene (PPeAn) groups at the bay position of perylene bisimide are designed and synthesized. The images of scanning and transmission electron microscopies for PPery and PPeAn show that both polymers form uniform nanoparticles. These copolymers emit red photoluminescence at around 640 nm with a relatively high Photoluminescence quantum yield, 48% (in solution) for PPery and 68% (in solution) for PPeAn.
Synthesis and Properties of Polyimides Containing Phthalide Groups

鲁云华,王巍,肖国勇,赵洪斌,董岩,迟海军,王同华,胡知之

DOI: https://doi.org/10.11777/j.issn1000-3304.2016.15348

2016-01-01

Acta Polymerica Sinica

Abstract:3, 3-Bis [4-(4-aminophenoxy) phenyl phthalide (I) and 3, 3-bis [4-(4-amino-2-trifluoro-methylphenoxy) phenyl] phthalide (II) were prepared through the nucleophilic substitution reaction of 4-nitrochlorobenzene' and 2-chloro-5-nitrobenzotrifluoride with phenolphthalein in the presence of potassium carbonate to yield the intermediate dinitro compounds 3,3-bis [4-(4-nitrophenoxy) phenyl] phthalide and 3,3-bis[ 4-(4-nitro-2-trifluoromethylphenoxy) phenyl] phthalide, followed by catalytic reduction with hydrazine and Pd/C. Eight kinds of phthalide-containing polyimide (PI) films were prepared from diamines I and II and four kinds of dianhydrides 1, 2, 3, 4-cyclobutanetetracarboxylic dianhydride (CBDA), pyromellitic dianhydride (PMDA), 3, 3', 4, 4'-oxydiphthalic anhydride (ODPA) and 4, 4'-hexafluoroisopropylidinedi (phtalic anhydride) (6 FDA) via thermal imidization of poly (amic acid) s separately. The chemical structure and properties of these PIs were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), ultraviolet-visible spectrophotometry (UV-Vis), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and solubility testing. These obtained experimental results showed that these PIs containing phthalide groups showed excellent thermal properties, optical properties and solubility. These PIs exhibited amorphous structure and showed good solubility in some aprotic polar organic solvents such as NMP, DMF, even soluble in weak polar solvent such as THF. They also exhibited excellent thermal properties, 10% thermal decomposition temperature above 498. 9 degrees C and the glass transition temperature (T-g) above 258 degrees C. The UV-Vis transmittance spectra showed that the PIs derived from CBDA, ODPA, 6FDA possessed optically colorless and transparent properties in the visible region. These obtained PIs containing phthalide groups could be expected to be used in the microelectronic and opto-electronic applications.
Synthesis and Characterization of Novel Triphenylamine—Containing Electrochromic Polyimides with Benzimidazole Substituents

Kuangguo Yan,Haiquan Chen,Chenjie Zhu,Zhao Ke,Dongwu Li,Mengxia Wang,Fengna Dai,Youhai Yu

DOI: https://doi.org/10.3390/molecules28052029

IF: 4.6

2023-02-22

Molecules

Abstract:Two novel electrochromic aromatic polyimides (named as TPA-BIA-PI and TPA-BIB-PI, respectively) with pendent benzimidazole group were synthesized from 1,2-Diphenyl-N,N′-di-4-aminophenyl-5-amino-benzimidazole and 4-Amino-4′-aminophenyl-4′′-1-phenyl-benzimidazolyl-phenyl-aniline with 4,4′-(hexafluoroisopropane) phthalic anhydride (6FDA) via two-step polymerization process, respectively. Then, polyimide films were prepared on ITO-conductive glass by electrostatic spraying, and their electrochromic properties were studied. The results showed that due to the π-π* transitions, the maximum UV–Vis absorption bands of TPA-BIA-PI and TPA-BIB-PI films were located at about 314 nm and 346 nm, respectively. A pair of reversible redox peaks of TPA-BIA-PI and TPA-BIB-PI films that were associated with noticeable color changed from original yellow to dark blue and green were observed in the cyclic voltammetry (CV) test. With increasing voltage, new absorption peaks of TPA-BIA-PI and TPA-BIB-PI films emerged at 755 nm and 762 nm, respectively. The switching/bleaching times of TPA-BIA-PI and TPA-BIB-PI films were 13 s/16 s and 13.9 s/9.5 s, respectively, showing that these polyimides can be used as novel electrochromic materials.

chemistry, multidisciplinary,biochemistry & molecular biology
Quaternary Copolymerized Polyimides and Negative Photosensitive Polyimide: Preparation and Properties

Jiahao Wu,Shiyang Zhang,Mingwei Cai,Qingling Li,Zhi Wang,Xiaochuang Lu,Yonggang Min

DOI: https://doi.org/10.1177/09540083231195528

IF: 1.73

2023-01-01

High Performance Polymers

Abstract:Photosensitive polyimide (PSPI) have been developed base on polyimide (PI). PSPI can be used as insulating and protective materials in the microelectronics industry due to the excellent insulating properties, thermal stability, and chemical stability. In this work, we designed a synthetic method to improve the regularity of the polymer chain segment sequence. Quaternary block copolymerized precursors were prepared using condensation polymerization of poly (acid amid). A photosensitive poly (acid amid) salts (co-PAS) was also synthesized to produce patterns with photochemical reaction. After imidization, the resolution of copolymerized PSPI (co-PSPI) pattern was in the range of 16 & mu;m-110 & mu;m. Partial photoreactive cross-linking structure was maintained to improve the thermal stability of co-PSPI. The co-PSPI exhibited higher glass transition temperatures (327.0 & DEG;C-358.8 & DEG;C) than copolymerized PI (307.4 & DEG;C-332.9 & DEG;C). This work provides the study on the synthesis and properties of quaternary copolymerized PI and PSPI.
Synthesis and Characterization of Photosensitive Polyimides Containing Chalcone Moiety in the Main Chain

李元勋,唐先忠,胡文成

DOI: https://doi.org/10.3321/j.issn:1001-9731.2005.01.032

2005-01-01

Abstract:In this paper,a kind of photosensitive diamines containing chalcone moiety named respectively as 1-(3-aminophenyl)-3-(4-aminophenyl)-2-propen-1-one (Ⅰ) and 1-(3-aminophenyl)-3-{4-(3-(3-aminophenyl)-3-oxo-1-propenyl) phenyl}-2-Propen-1-one (Ⅱ) were synthesized. The preparation and properties of novel soluble photosensitive polyimides (PSPI) based on photosensitive diamines and pyromellitic dianhydride are studied by means of TGA,UV and GPC analysis. This synthetic method has the advantages of simpleness,cheapness,high yield and purity. The molecular weights of resins are easy controlled and their exposal wavelengths are suited for I-line of industry with high performance of heat-resistance and sensitization.

Photoconductive polyimides based on bisphenyl-porphyrin II: structure and photoconductive properties of polyimide and their precursor films

Photoconductive Polyimides Based On Bisphenyl-Porphyrin I: Synthesis And Characterization.

Synthesis and photoconductive characteristics of biphenylporphyrin-containing poly(amic acid)s and polyimides

Photoconductive polyimide (3). Preparation and photoconductivity of polyimide LB films containing carbazole and copper-phthalocyanine groups

Photoconductivity of Copolyimide Films Containing Tetraphenylporphyrin and Carbazole Moieties

Synthesis and electrophotographic properties of copolyimides containing tetraphenylporphyrin

Enhancing The Photoconductivity Of Polyimides By Incorporating Intrinsic Chromophore Units

A study of photoconductive polyimides(I) - Synthesis, characterization and the photoconductivity study of polymers containing carbazole and phthalocyanine groups

A study of photoconductive polyimides .1. Synthesis, characterization and the photoconductivity study of polymers containing carbazole and phthalocyanine groups

Study on Photoconduction Properties of Polyimide Films Containing Tetraphenylporphyrin Units

Photoelectrical Properties of Polyaniline/polyimide Complex Thin Film

Synthesis And Characterization Of Porous Polyimide Films Containing Benzimidazole Moieties

Solubility, Thermal and Photoluminescence Properties of Triphenyl Imidazole-Containing Polyimides.

Optical and Electrical Properties of Cu-Phthalocyanine-doped Polyimide Thin Films by Vapor Deposition Polymerization

Preparation and Properties of Polyimides Based on Bis[3,5-Dimethyl-4-(4-Aminophenoxy)Phenyl]Methane

Synthesis and Characterization of Biphenyl Polyimide Containing Alkyl Sulfide Structure

Synthesis and Characterization of New Types of Perylene Bisimide‐Containing Conjugated Copolymers

Synthesis and Properties of Polyimides Containing Phthalide Groups

Synthesis and Characterization of Novel Triphenylamine—Containing Electrochromic Polyimides with Benzimidazole Substituents

Quaternary Copolymerized Polyimides and Negative Photosensitive Polyimide: Preparation and Properties

Synthesis and Characterization of Photosensitive Polyimides Containing Chalcone Moiety in the Main Chain