Abstract:Tungsten and tungsten alloys are widely used in high temperature environments where arc ablation or mechanical deformation and damage are the main sources of materials failure. For high temperature critical applications in thermomechanical environments, however, the low strength limits the use of tungsten and tungsten alloys. Hence, new tungsten based materials with good high temperature thermomechanical properties need to be developed in order to extend the use of tungsten. TiC particle-reinforced tungsten based composites (TiCp/W) were fabricated by hot pressing at 2000 °C, 20 MPa in a vacuum of 1.3×10−3 Pa. The composites were examined with respect to their thermophysical and mechanical properties at room temperature and at elevated temperature. Vickers hardness and elastic modulus increased with increasing TiC content from 0 to 40 vol.%. The highest flexural strength, 843 MPa, and the highest toughness, 10.1 MPam1/2, of the composites at room temperature were all obtained when 20 vol.% TiC particle were added. As the test temperature rose, the flexural strength of the TiCp/W composites firstly increased and then decreased, except in the monolithic tungsten. The highest strength of 1155 MPa was measured at 1000 °C in the composite containing 30 vol.% TiC particles. The strengthening effect of TiC particles on the tungsten matrix is more significant at high temperatures. With the addition of TiC particles, the thermal conduction of tungsten composites was drastically decreased from 153 Wm−1K−1 for monolithic W to 27.9 Wm−1K−1 for 40 vol.% TiCp/W composites, and the thermal expansion was also increased. The new composites are successfully used to make high temperature grips and moulds.

Processing and Mechanical Properties of 30vol%TiCp/W Composite

Effects of Process Parameters on Microstructure and Properties of TiC Reinforced Cu-Matrix Composites

Mechanical properties of short carbon fiber-reinforced TiC composites produced by hot pressing

Microstructure and mechanical properties of 20Wf/30ZrCp/W composite

Microstructure and properties of TiCp/30CrNi4Mo steel-based composites prepared by hot isostatic press

Effect of Powder Synthesis Processing on Microstructure and Mechanical Properties of TiB2-TiC Composite Ceramics

Thermophysical Properties of TiCp/W Composites

Elevated temperature strength of TiCp/W composites

Influence of TiC Content on Microstructure and Properties of W-30Cu/TIC Composites

Microstructure and mechanical properties of TiB2-40 wt% TiC composites: Effects of adding a low-temperature hold prior to sintering at high temperatures

Microstructure and Mechanical Properties of in Situ Synthesised (Tic+tib)/ti-6Al-4v Composites Prepared by Powder Metallurgy

Processing, Microstructural Characterization and Mechanical Properties of in Situ Ti3AlC2/TiAl3 Composite by Hot Pressing

Influence of Hot-Pressing Parameters on the Mechanical Properties of TiC Composites Reinforced with Carbon Fibers

Effect of TiCp Volume Fraction and WCp Addition on the Mechanical Properties of TiCp/Cr8Mo2VSi Composites

Influence of TiC Content on Microstructure and Properties of W-3OCu/TiC Composites

Thermomechanical Properties of TiC Particle-Reinforced Tungsten Composites for High Temperature Applications

The Influence of TiC Content on The Properties of Tungsten Matrix Composites

Effect of Silver Element on Microstructure and Properties of W-30Cu/TiC Composites

Effect of TiC content on the microstructure and mechanical properties of Ti-30Mo-xTiC composites

Design and Strengthening Behaviour of Ti2alc/Tial Composite by Low-Temperature Hot-Pressing Process

Mechanical Properties and Microstructures of W–TiC and W–Y2O3 Alloys Fabricated by Hot-Pressing Sintering