Abstract:Tungsten and tungsten alloys are widely used in high temperature environments where arc ablation or mechanical deformation and damage are the main sources of materials failure. For high temperature critical applications in thermomechanical environments, however, the low strength limits the use of tungsten and tungsten alloys. Hence, new tungsten based materials with good high temperature thermomechanical properties need to be developed in order to extend the use of tungsten. TiC particle-reinforced tungsten based composites (TiCp/W) were fabricated by hot pressing at 2000 °C, 20 MPa in a vacuum of 1.3×10−3 Pa. The composites were examined with respect to their thermophysical and mechanical properties at room temperature and at elevated temperature. Vickers hardness and elastic modulus increased with increasing TiC content from 0 to 40 vol.%. The highest flexural strength, 843 MPa, and the highest toughness, 10.1 MPam1/2, of the composites at room temperature were all obtained when 20 vol.% TiC particle were added. As the test temperature rose, the flexural strength of the TiCp/W composites firstly increased and then decreased, except in the monolithic tungsten. The highest strength of 1155 MPa was measured at 1000 °C in the composite containing 30 vol.% TiC particles. The strengthening effect of TiC particles on the tungsten matrix is more significant at high temperatures. With the addition of TiC particles, the thermal conduction of tungsten composites was drastically decreased from 153 Wm−1K−1 for monolithic W to 27.9 Wm−1K−1 for 40 vol.% TiCp/W composites, and the thermal expansion was also increased. The new composites are successfully used to make high temperature grips and moulds.

The Influence of TiC Content on The Properties of Tungsten Matrix Composites

Effect of TiB_2 content on microstructure and mechanical properties of in-situ fabricated TiB_2/B_4C composites

THE INFLUENCE OF ZrC PARTICLE CONTENT ON THE MECHANICAL PROPERTIES OF TUNGSTEN MATRIX COMPOSITES

Effect of TiC content on the microstructure and mechanical properties of Ti-30Mo-xTiC composites

Thermophysical Properties of TiCp/W Composites

Effect of TiC Content on Microstructure and Mechanical Properties of High-temperature Titanium Matrix Composites

Effect of TiCp Volume Fraction and WCp Addition on the Mechanical Properties of TiCp/Cr8Mo2VSi Composites

Influence of TiC Content on Microstructure and Properties of W-3OCu/TiC Composites

Influence of TiC Content on Microstructure and Properties of W-30Cu/TIC Composites

The microstructure and elevated temperature strength of tungsten-titanium carbide composite

Thermomechanical Properties of TiC Particle-Reinforced Tungsten Composites for High Temperature Applications

Microstructural evolution, mechanical and thermal properties of TiC-ZrC-Cr3C2 composites

Effects of Process Parameters on Microstructure and Properties of TiC Reinforced Cu-Matrix Composites

Effect of Ti Additives on the Sintering Behavior and Mechanical Properties of ZrC-W Composites

Effect of TaC Content on Microstructure and Properties of W-TaC Composites

Mechanical properties of short carbon fiber-reinforced TiC composites produced by hot pressing

Comparative Investigation on Microstructures and Mechanical Properties of (tib + TiC)/Ti-6Al-4V Composites from Ti-B4C-C and Ti-TiB2-TiC Systems

Influence of Matrix Characteristics on Tensile Properties of in Situ Synthesized TiC/TA15 Composite

Influence of Hot-Pressing Parameters on the Mechanical Properties of TiC Composites Reinforced with Carbon Fibers

Effect of Cr Contents on Microstructure and Mechanical Properties of ( TiBw + TiCp)/(Ti-4.0Fe-7.3Mo-xCr) Composites

Effect of Active Powder Addition on the Mechanical Properties of TiCp/Manganese Steel Matrix Composites