Effect of pH value on the property of BaTiO3 nano powder

A. N W L Lu,Lian Gao,Jingkun Guo

IF: 1.292

1999-01-01

Journal of Inorganic Materials

Abstract:The property of BaTiO3 nano powder prepared by the sol-gel method at different pH values was investigated. The effect of pH value on gel formation and aggregates was discussed with double electric layer theory and reaction mechanism. The optimal preparing condition of the powder was proposed (pH>8).

What problem does this paper attempt to address?

Influence of Ph Value on Properties of Nanocrystalline BaTiO3 Powder

WL Luan,L Gao

DOI: https://doi.org/10.1016/s0272-8842(01)00012-8

IF: 5.532

2001-01-01

Ceramics International

Abstract:Nanocrystalline BaTiO3 powders were prepared by a simple sol-gel method starting from comparatively cheap raw materials. The effect of pH value on the properties of BaTiO3 powder was investigated. It was found that the pH value of solvent has a great influence on the process of powder fabrication, including colloid formation, gel structure and agglomerates. The mechanism was discussed and the optimal powder preparing condition was proposed in this paper. As-prepared powder was pseudo cubic structure with an average grain size of 13 nm (TEM) and a high BET value of 33 m2/g.
pH control on preparation of nano-TiO_2 by gel-sol process

Zhou Limin,Liu Zhirong,Huang Qunwu

DOI: https://doi.org/10.3969/j.issn.1006-4990.2007.03.010

2007-01-01

Abstract:Nano-TiO2 was prepared by gel-sol method and were characterized by transmission electron microscopy(TEM) and X-ray diffraction patterns(XRD).The pH change and the effects of electrolyte(NaClO4) on it were studied.The effects of initial pH value(pH0) on the shapes of TiO2 and the system composition were also investigated.The results showed that the synthesized products were anatase TiO2 with the average diameter of 5-15 nm.The change in pH value was mainly governed by the adsorption and desorption process of H+ and OH-on the surface of Ti(OH)4 or TiO2.This process can be enhanced by adding 0.1 mol/L NaClO4.The shapes of TiO2 and the system composition were greatly influenced by different pH0.The spheroidal crystals of TiO2 at pH0=1.0 became cuboidal at pH0=9.4 and ellipsoidal at pH0=11.5.The fraction of a mount of substance of TiO2 decreased significantly at pH0>9.4 and no TiO2 was produced at pH0=12.0,so pH0 below 9.4 is the optimum parameter for TiO2 preparation in our experiments.
Effects of pH on Preparation and Properties of CaTi2O4(OH)2 by Hydrothermal Method

Wei Xia Dong,Gao Ling Zhao,Xing Yong Gu,Bin Song,Gao Rong Han

DOI: https://doi.org/10.4028/www.scientific.net/kem.602-603.15

2014-01-01

Key Engineering Materials

Abstract:A novel CaTi2O4(OH)2 nanosheet was synthesized using anhydrous calcium chloride, lithium chloride and butyl titanate as the basic raw material by a template-free and surfactant-free hydrothermal method. The crystal structure, morphology and element synthesis were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM) equipped with an EDS system. Effects of pH on the structure, morphology and electrochemical properties were investigated. The results showed that when pH was 6.7, CaTi2O5 phase was obtained. When pH was 8.3, pure CaTi2O4(OH)2 nanosheets were obtained. Further increasing pH to 8.6, CaTi2O4(OH)2 was obtained, however, and CaTiO3 phase also appeared. When pH was 8.3, the rate capacity of CaTi2O4(OH)2 nanosheets was further higher than those of the samples prepared for pH=6.7 and pH=8.6. It indicated that CaTi2O4(OH)2 nanosheets were helpful for lithium insertion and de-intercalation. The sample synthesized at pH=8.3 showed the best electrochemical performances, with first discharge specific capacity of 177.9 mAh/g at 0.1C rate. The CaTi2O4(OH)2 nanosheets might represent an opportunity for the applications in lithium ion battery.
Effects of Ph on Preparation and Properties of CaTi2O4(OH)2 by Hydrothermal Method

W. Dong,Gao Ling Zhao,Xing Yong Gu,Bin Song,Gao Rong Han

DOI: https://doi.org/10.4028/www.scientific.net/kem.602-603.15

2014-01-01

Key Engineering Materials

Abstract:A novel CaTi 2 O 4 (OH) 2 nanosheet was synthesized using anhydrous calcium chloride, lithium chloride and butyl titanate as the basic raw material by a template-free and surfactant-free hydrothermal method. The crystal structure, morphology and element synthesis were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM) equipped with an EDS system. Effects of pH on the structure, morphology and electrochemical properties were investigated. The results showed that when pH was 6.7, CaTi 2 O 5 phase was obtained. When pH was 8.3, pure CaTi 2 O 4 (OH) 2 nanosheets were obtained. Further increasing pH to 8.6, CaTi 2 O 4 (OH) 2 was obtained, however, and CaTiO 3 phase also appeared. When pH was 8.3, the rate capacity of CaTi 2 O 4 (OH) 2 nanosheets was further higher than those of the samples prepared for pH=6.7 and pH=8.6. It indicated that CaTi 2 O 4 (OH) 2 nanosheets were helpful for lithium insertion and de-intercalation. The sample synthesized at pH=8.3 showed the best electrochemical performances, with first discharge specific capacity of 177.9 mAh/g at 0.1C rate. The CaTi 2 O 4 (OH) 2 nanosheets might represent an opportunity for the applications in lithium ion battery.
The Effect of pH value on the nano-particle size of bi substituted yttrium iron garnet

Yanpeng Qiu,Xiwen Zhang,Gaorong Han

DOI: https://doi.org/10.3321/j.issn:1002-185X.2006.z2.047

2006-01-01

Rare Metal Materials and Engineering

Abstract:Nano-particles of Bi substituted yttrium iron garnet were prepared by co-precipitation method, with the pH value being 9, 10, 11 or 12. The nano-particle size, size distribution and the structure of hydroxide precursor were observed with transmission electron microscope (TEM). The TEM images show that the size of Bi-YIG grains decreases obviously and the distribution of the particles becomes symmetrical with the increase of pH value. When the pH value is 12, the particle size is the smallest, varying around 10 nm. And the structure of hydroxide precursor is kind of net when the pH value is 9, 10 and 11. In addition, the net structure becomes more integrated with the increases of pH value. But the hydroxide precursor becomes several dispersive particles when the pH value reaches 12. The mechanism of the effect of pH value on nano-particles is discussed by analyzing the hydroxide precursor. The Bi-YIG particles prepared at different pH values were tested with the X-ray diffraction (XRD), and the influence of pH value to the synthesis of garnet phase was analyzed also.
Effect of pH value on synthesis process and luminescence behavior of p-hydroxybenzoic acid-terbium complex in gel

XP Fan,XQ Qian,J Qian

DOI: https://doi.org/10.3321/j.issn:1002-185X.2004.z1.012

2004-01-01

Xiyou Jinshu Cailiao Yu Gongcheng/Rare Metal Materials and Engineering

Abstract:The effect of pH value on the synthesis process and luminescence behavior of ρ-hydroxybenzoic acid-terbium complex in gel have been investigated. With the increase of pH value, the luminescence intensity of theρ p-hydroxybenzoic acid and TbCl3 Co-doped SiO2 gel increases gradually, which indicates that the ρ-hydroxybenzoic acid-terbium complex has been synthesized in the gel. However, the luminescence intensity decreases with the increase of pH value. in the (50%TEOS+50%GPTMS) gel.
Effects of Water Amount and Ph on the Crystal Behavior of a TiO2 Nanocrystalline Derived from a Sol–Gel Process at a Low Temperature

Zhijun Chen,Gaoling Zhao,Hong Li,Gaorong Han,Bin Song

DOI: https://doi.org/10.1111/j.1551-2916.2009.03047.x

IF: 4.186

2009-01-01

Journal of the American Ceramic Society

Abstract:TiO2 nanocrystallines with a size of 3–7 nm have been synthesized by the sol–gel method with excessive water at a low temperature of about 50°C. The effects of amount of water and pH on the formation of sols and powders containing TiO2 nanocrystallines were investigated by X‐ray powder diffraction (XRD), transmission electron microscopy, and high‐resolution transmission electron microscopy. The results showed that a pure anatase phase was formed at pH 1, in contrast to the formation of particles with a mixture of anatase and brookite phases at pH 2–7. Moreover, at pH 1, the intensity of the XRD peaks and the crystal size increased with increasing water content when the water ratio increased from 40 to 100. Whereas the crystal intensity remained invariant, the crystal size still increased when the water ratio increased from 100 to 400. The photocatalytic activity was also investigated. It was shown that when the water ratio was below 100, the photocatalytic activity increased with increasing water content. Further increase of the water content decreased the photocatalytic activity. The photocatalytic activity decreased with increasing pH. All samples with pH=1 showed better photocatalytic activity than Degussa P25. Mechanisms for the formation of the TiO2 nanocrystalline particles at such a low temperature were also discussed.
PREPARATION AND SINTERING PROPERTIES OF BaTi4O9 BY CITRIC ACID GEL METHOD

Wei Wang,Qilong Zhang,Hui Yang

DOI: https://doi.org/10.3969/j.issn.1000-2278.2006.04.001

2006-01-01

Journal of Ceramics

Abstract:Single phase has been prepared via citric acid gel method through two steps calcining procedure.Calcining the dried gel at 750℃resulted in nanocrystalline (30～50nm) precursor powders containing intimate blending of BaTi_5O_(11) and Ba_4Ti_(13)O_(30), and single phase could be obtained when calcining the precursor powders at 1200℃for 2h.The single phase powders had good sinterability and when sintering at 1250℃for 4h reached 97% of the theoretical density.
Structure and Electrical Properties of BaTiO3 Prepared by Sol–gel Process

Wei Li,Zhijun Xu,Ruiqing Chu,Peng Fu,Jigong Hao

DOI: https://doi.org/10.1016/j.jallcom.2009.02.137

IF: 6.2

2009-01-01

Journal of Alloys and Compounds

Abstract:BaTiO3 nanopowders were synthesized from alkoxide solution precursor by sol–gel process. Attempts had been made to understand the synthesis process with the help of thermo gravimetric (TG) and differential scanning calorimetry (DSC). XRD and SEM results showed that the BaTiO3 powders calcined at 700°C for 2h were maintained in cubic phase and the average size was 25nm. The effects of the initial grain sizes of BaTiO3 powders on the phase structures, microstructures and dielectric properties of the ceramics were investigated. The results indicated that both the grain size and the relative density of the ceramics increased with the increase in sintered temperature. The permittivity at room temperature was not sensitive to the grain size.
Effect of NaOH Concentration on Formation of Ba4Ti13O30 and BaTi5O11 Nanocrystals Prepared by Hydrothermal Method

Kai Zou,Long Liu,Xinyi Li,Shaoqing Li,Zhixiong Huang,Lianmeng Zhang,Dongyun Guo,Yang Ju

DOI: https://doi.org/10.1016/j.matlet.2019.126584

IF: 3

2019-01-01

Materials Letters

Abstract:The Ba4Ti13O30 and BaTi5O11 nanocrystals were synthesized by a hydrothermal method, and the effect of NaOH concentration on formation of Ba4Ti13O30 and BaTi5O11 nanocrystals was investigated. In the Ba-Ti precursors, the concentrations of Ba2+ and Ti4+ ions were kept at 0.018 and 0.082 mol/L, and the NaOH concentration changed from 1 to 8 mol/L. As the Ba-Ti precursors were heated in the autoclave at 280 degrees C for 20 h with vigorous stirring, the pure BaTi5O11 nanocrystals with rice-like morphology were obtained at NaOH concentration of 1 mol/L, and the Ba4Ti13O30 nanowires were co-formed with the rice-like BaTi5O11 nanocrystals at NaOH concentration of 2 mol/L. With increasing the NaOH concentration, the amount of Ba4Ti13O30 nanowires increased. The phase evolution from monoclinic BaTi5O11 to orthorhombic Ba4Ti13O30 could be controlled by adjusting NaOH concentration. (C) 2019 Elsevier B.V. All rights reserved.
Structure and Electrorheological Properties of Nanoporous BaTiO3 Crystalline Powders Prepared by Sol–gel Method

Wanquan Jiang,Chuanxia Jiang,Xinglong Gong,Zhong Zhang

DOI: https://doi.org/10.1007/s10971-009-2011-5

2009-01-01

Journal of Sol-Gel Science and Technology

Abstract:In this paper, a novel nanoporous barium titanate (BaTiO3) crystalline powder was synthesized by using triblock poly(ethylene oxide) (PEO) and poly(propylene oxide) (PPO) based systems (P-123) as the soft template via a sol-gel method and their structure-dependent electro rheological property was studied. The pore diameter and specific surface area of BaTiO3 were precisely controlled by varing the calcined temperature. The chemical composition, structure and surface morphology of BaTiO3 were characterized by X-ray diffraction (XRD), thermo gravimetric analysis (TGA), and nitrogen adsorption-desorption method, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The result revealed that the pore volume and specific surface area of BaTiO3 decreased with the increment of calcined temperature. The electro rheological fluids (ERFs) were obtained by dispersing BaTiO3 crystallites in silicon oil and three kinds ERFs were fabricated by using three kinds of BaTiO3 which were prepared under different calcined temperature (550, 600 and 900 A degrees C) as the precursors. The behaviors of the ERFs were evaluated via a rotational rheometer fixed with electric field generator. The results showed that electro rheological effect was related to the pore volume and specific surface area of BaTiO3. Due to the distinct advantage of sol-gel method for preparing nanoporous BaTiO3 without contamination of the materials, the markedly low current destiny of the ERFs was obtained. The yield stress of ERFs with large specific surface area of BaTiO3 reached the maximum of 3 kPa, which is higher than that of ERFs using traditional pure BaTiO3 crystallites (lower than 1 kPa).
Citric Acid Gel Method Synthesis, Characterization And Dielectric Properties Of Single-Phase Bati4o9

Zhang Qilong,Yang Hui,Wang Wei

DOI: https://doi.org/10.3321/j.issn:1002-185X.2008.z2.133

2008-01-01

Rare Metal Materials and Engineering

Abstract:Single-phase BaTi4O9 was prepared by citric acid gel method with two-step heat-treatment. Nanocrystalline precursor powders including BaTi5O11 and Ba4Ti13O30 of 30-50 nm were obtained by heat-treating xerogel at 750 degrees C. Due to the higher surface activity of nanocrystalline precursor powder, the single-phase BaTi4O9 can be obtained when heat-treating the precursor at 1200 degrees C. The powder thus prepared had improved sintering characteristic and dielectric properties compared to those prepared by one-step heat-treatment method. When sintering the powder from two-step heat-treatment method at 1250 degrees C for 4 h, the 97% theoretical density (TD) BaTi4O9 ceramics could be obtained with dielectric properties: epsilon(r)= 36.33, Qxf=28 100 GHz, tau(f) = 16.2 X 10(-6)/degrees C.
Room-Temperature Synthesis of BaTiO3Nanoparticles in Large Batches

Xiao Wei,Gang Xu,Zhaohui Ren,Ge Shen,Gaorong Han

DOI: https://doi.org/10.1111/j.1551-2916.2008.02695.x

IF: 4.186

2008-01-01

Journal of the American Ceramic Society

Abstract:A new method has been developed to synthesize barium titanate (BaTiO3) nanoparticles with a narrow size distribution under ambient conditions at room temperature. The as-prepared BaTiO3 nanoparticles were characterized by X-ray diffraction, transmission electron microscopy, high-resolution TEM, and selected area electron diffraction. On the basis of the characterizations, it was found that the particle size could be easily tuned by adjusting the experimental parameters, such as the solvent component and reaction time. The basicity of the organic solvent was considered to play an important role in the room-temperature synthesis and the solvent molecules had a strong influence on the crystal growth of BaTiO3 nanoparticles. The BaTiO3 nanoparticles obtained were well dispersed and possessed a cubic perovskite structure at room temperature.
Study on BaBi4Ti4O15 nanoscaled powders prepared by sol–gel method

Dan Xie,Wei Pan

DOI: https://doi.org/10.1016/S0167-577X(02)01406-4

IF: 3

2003-01-01

Materials Letters

Abstract:Bi-layered structure ferroelectric material—BaBi4Ti4O15 (BBT) powders with the order of magnitude of nanometer were prepared by sol–gel process using barium acetate, bismuth nitrate and tetrabutyl titanate as sources. The reaction mechanism of BBT precursor solution, and the preparation and characteristics of BBT powders were studied using simultaneous thermal analyzer, X-ray diffraction (XRD), and particle analysis and scanning electron microscopy (SEM). Ethanolamine is an effective complexation reagent of Bi3+, which could control the hydrolysis of Bi(NO3)3. When pH value is about 3.5, the stable and uniform BBT precursor could be obtained. The Bi-layered perovskite structure of BBT powder forms at 750 °C. The granularity distribution is centralized from 150 to 180 nm and the average particle size is about 160 nm. It is obvious that sol–gel process can be used to prepare nanoscaled powder for new kinds of ferroelectric materials.
Preparation of BaBi4Ti4O15 powder by sol-gel process

Hui Shi,Wei Pan,Dan Xie

2002-01-01

Rare Metal Materials and Engineering

Abstract:BaBi4Ti4O15 powder was prepared by Sol-Gel method. The powder was characterized by differential thermal analysis (DTA), X-ray diffraction (XRD), granularmetric analysis and soon. The results indicate that when the pH value of the precursor is 3.5, the Ba-Bi-Ti sol-gel can be prepared, and BaBi4Ti4O15 powder was obtained at the condition of calcining temperature of 750degreesC and heating rate of 10degreesC/min. The crystal size is about 60nm,and the particle size of the powder is from 150nm to 200nm, with the average size of 175nm or so. The experimental results show that BaBi4Ti4O15 powder can be produced by Sol-Gel process.
The Influence of the Synthesis Method on the Characteristics of BaTiO3

G N Almeida,R N de Souza,L F S Lima,N D S Mohallem,E P da Silva,A M A Silva

DOI: https://doi.org/10.3390/ma16083031

2023-04-11

Abstract:In this work, barium titanate powders were produced by sol-gel and sol-precipitation methods from metal alkoxides. In the sol-gel method, tetraisopropyl orthotitanate was mixed with 2-propanol, acetic acid and barium acetate, and the gel samples obtained were calcined at 600 °C, 800 °C and 1000 °C. Through the sol-precipitation method, tetraisopropyl orthotitanate was mixed with acetic acid and deionized water and precipitated by the addition of a concentrated solution of KOH. The products were calcined at various temperatures, and the microstructural and dielectric properties of the BaTiO3 prepared for the two processes were analyzed and compared. The results of these analyses allowed us to observe an increase in the tetragonal phase and the dielectric constant (15-50 at 20 kHz) with increasing temperatures in the samples produced by the sol-gel method, while the sample obtained by sol precipitation was cubic. The presence of BaCO3 is more evident in the sample produced by sol-precipitation, and the band gap of the products obtained did not show significant variation, changing the synthesis method (3.363-3.594 eV).
Comparisons of nanostructured BaTiO3 powders synthesized by sol-gel method and sol-precipitation method

WeiLing Luan,Lian Gao,Jingkun Guo

1999-01-01

Abstract:Comparisons of two kinds of nanocrystalline BaTiO3 synthesized by sol-gel method and sol-precipitation method were made. Powders obtained by sol-gel method were homogeneous and ultrafine (17nm), with a few amounts of BaCO3 which disappeared by increasing the calcinating temperature. Pure crystalline BaTiO3 with larger grain size of 42nm and some degrees of aggregates were obtained by sol-precipitation method Mechanisms for the evolution of crystalline BaTiO3 in the sol-gel and the sol-precipitation method were discussed in the context of microstructure.
Effect of pH value on multiferroic properties of barium ferrite ceramics prepared by sol–gel method

Zhixin Zeng,Mengshuang Lan,Qin Zhang,Simin Chen,Zhenhua Wang,Xiang Lei,Xiaoling Deng,Rongli Gao,Wei Cai,Gang Chen,Chunlin Fu,Songlin Chen

DOI: https://doi.org/10.1016/j.jmmm.2022.169904

IF: 3.097

2022-12-01

Journal of Magnetism and Magnetic Materials

Abstract:In this paper, BaFe12O19 (BaM) ceramics at different pH values were prepared by sol–gel method. Effects of pH value on the microstructure, electrical as well as magnetic properties were systematically studied. XRD indicate that the ceramics were mainly BaM. However, with the pH value increasing further, the BaFe2O4 impurity phase appears gradually in both powders and ceramics due to the degree of complexation between citric acid and metal cations and other reasons. SEM results show that the grain size of ceramics decreases from 2.28 μm to 1.35 μm with the pH value increase from 4 to 8. It is found that room temperature dielectric constant, residual polarization, and saturation magnetization of the ceramics is the largest when the pH value of the solution is 4, which are 0.108 μC/cm2 and 32.829 emu/g, respectively. The dielectric constant and residual polarization of ceramics decrease with the increase of pH value. The ferroelectric and magnetic hysteresis loops have confirmed room-temperature multiferroic properties of the prepared ceramics. It laid the foundation for the further development of new room temperature single-phase multi-iron materials.

materials science, multidisciplinary,physics, condensed matter
Preparation of LiTaO 3 nanoparticles by a sol–gel route

Y. G. Liu,J. H. Hu,Z. H. Huang,M. H. Fang

DOI: https://doi.org/10.1007/s10971-011-2442-7

2011-01-01

Journal of Sol-Gel Science and Technology

Abstract:A sol–gel route was developed to prepare pure ultrafine LiTaO 3 powders using Ta 2 O 5 , Li 2 CO 3 , citric acid (CA) as chelating agent, ethylene glycol (EG) as esterification agent and polyethylene glycol (PEG) as dispersant. The effects of pH value and heat treatment temperature of powder precursor on the synthesis of LiTaO 3 powders were investigated. The phase content and morphology of the final product were evaluated by XRD, SEM and TEM. A transparent gel was produced when heating a mixed-solution of CA, EG, Li and Ta ions with a molar ratio of [CA]:[EG]:[Li]:[Ta] = 3.0:6.0:1.0:1.0 and 2‰ PEG additions with a pH value of 7 at water bath temperature of 80 °C. The results showed that single phase LiTaO 3 powders with average particle sizes of nanometers were produced after heat treatment of the powder precursor at 650, 700, 800, and 900 °C respectively for 2 h.
Preparation of LiTaO3 nanoparticles by a sol–gel route

Y. G. Liu,J. H. Hu,Z. H. Huang,M. H. Fang

DOI: https://doi.org/10.1007/s10971-011-2442-7

2011-01-01

Journal of Sol-Gel Science and Technology

Abstract:A sol-gel route was developed to prepare pure ultrafine LiTaO3 powders using Ta2O5, Li2CO3, citric acid (CA) as chelating agent, ethylene glycol (EG) as esterification agent and polyethylene glycol (PEG) as dispersant. The effects of pH value and heat treatment temperature of powder precursor on the synthesis of LiTaO3 powders were investigated. The phase content and morphology of the final product were evaluated by XRD, SEM and TEM. A transparent gel was produced when heating a mixed-solution of CA, EG, Li and Ta ions with a molar ratio of [CA]:[EG]:[Li]:[Ta] = 3.0:6.0:1.0:1.0 and 2aEuro degrees PEG additions with a pH value of 7 at water bath temperature of 80 A degrees C. The results showed that single phase LiTaO3 powders with average particle sizes of nanometers were produced after heat treatment of the powder precursor at 650, 700, 800, and 900 A degrees C respectively for 2 h.

Effect of pH value on the property of BaTiO3 nano powder

Influence of Ph Value on Properties of Nanocrystalline BaTiO3 Powder

pH control on preparation of nano-TiO_2 by gel-sol process

Effects of pH on Preparation and Properties of CaTi<sub>2</sub>O<sub>4</sub>(OH)<sub>2</sub> by Hydrothermal Method

Effects of Ph on Preparation and Properties of CaTi<sub>2</sub>O<sub>4</sub>(OH)<sub>2</sub> by Hydrothermal Method

The Effect of pH value on the nano-particle size of bi substituted yttrium iron garnet

Effect of pH value on synthesis process and luminescence behavior of p-hydroxybenzoic acid-terbium complex in gel

Effects of Water Amount and Ph on the Crystal Behavior of a TiO2 Nanocrystalline Derived from a Sol–Gel Process at a Low Temperature

PREPARATION AND SINTERING PROPERTIES OF BaTi4O9 BY CITRIC ACID GEL METHOD

Structure and Electrical Properties of BaTiO3 Prepared by Sol–gel Process

Effect of NaOH Concentration on Formation of Ba4Ti13O30 and BaTi5O11 Nanocrystals Prepared by Hydrothermal Method

Structure and Electrorheological Properties of Nanoporous BaTiO3 Crystalline Powders Prepared by Sol–gel Method

Citric Acid Gel Method Synthesis, Characterization And Dielectric Properties Of Single-Phase Bati4o9

Room-Temperature Synthesis of BaTiO<sub>3</sub>Nanoparticles in Large Batches

Study on BaBi4Ti4O15 nanoscaled powders prepared by sol–gel method

Preparation of BaBi4Ti4O15 powder by sol-gel process

The Influence of the Synthesis Method on the Characteristics of BaTiO3

Comparisons of nanostructured BaTiO3 powders synthesized by sol-gel method and sol-precipitation method

Effect of pH value on multiferroic properties of barium ferrite ceramics prepared by sol–gel method

Preparation of LiTaO 3 nanoparticles by a sol–gel route

Preparation of LiTaO<sub>3</sub> nanoparticles by a sol–gel route

Effect of pH value on the property of BaTiO3 nano powder

Influence of Ph Value on Properties of Nanocrystalline BaTiO3 Powder

pH control on preparation of nano-TiO_2 by gel-sol process

Effects of pH on Preparation and Properties of CaTi<sub>2</sub>O<sub>4</sub>(OH)<sub>2</sub> by Hydrothermal Method

Effects of Ph on Preparation and Properties of CaTi&lt;sub&gt;2&lt;/sub&gt;O&lt;sub&gt;4&lt;/sub&gt;(OH)&lt;sub&gt;2&lt;/sub&gt; by Hydrothermal Method

The Effect of pH value on the nano-particle size of bi substituted yttrium iron garnet

Effect of pH value on synthesis process and luminescence behavior of p-hydroxybenzoic acid-terbium complex in gel

Effects of Water Amount and Ph on the Crystal Behavior of a TiO2 Nanocrystalline Derived from a Sol–Gel Process at a Low Temperature

PREPARATION AND SINTERING PROPERTIES OF BaTi4O9 BY CITRIC ACID GEL METHOD

Structure and Electrical Properties of BaTiO3 Prepared by Sol–gel Process

Effect of NaOH Concentration on Formation of Ba4Ti13O30 and BaTi5O11 Nanocrystals Prepared by Hydrothermal Method

Structure and Electrorheological Properties of Nanoporous BaTiO3 Crystalline Powders Prepared by Sol–gel Method

Citric Acid Gel Method Synthesis, Characterization And Dielectric Properties Of Single-Phase Bati4o9

Room-Temperature Synthesis of BaTiO<sub>3</sub>Nanoparticles in Large Batches

Study on BaBi4Ti4O15 nanoscaled powders prepared by sol–gel method

Preparation of BaBi4Ti4O15 powder by sol-gel process

The Influence of the Synthesis Method on the Characteristics of BaTiO3

Comparisons of nanostructured BaTiO3 powders synthesized by sol-gel method and sol-precipitation method

Effect of pH value on multiferroic properties of barium ferrite ceramics prepared by sol–gel method

Preparation of LiTaO 3 nanoparticles by a sol–gel route

Preparation of LiTaO<sub>3</sub> nanoparticles by a sol–gel route

Effects of Ph on Preparation and Properties of CaTi<sub>2</sub>O<sub>4</sub>(OH)<sub>2</sub> by Hydrothermal Method