Abstract:Applications of shape memory alloys require them have the ability to undergo back and forth through the solid-to-solid martensitic phase transformations for many times without degradation of properties (termed "reversibility"). Low hysteresis and small migration of transformation temperature under cycling are the macroscopic manifestation of high reversibility. By the crystallographic theory of martensite, materials with certain crystalline symmetry and geometric compatibility tend to form no-stressed transformation interface and have excellent functional stability. In the theory, several conditions that corresponding to extremely low hysteresis are specified. Stronger compatibility conditions which lead to even better reversibility have been theoretically proposed, those conditions are called "cofactor conditions". Recently, for the first time, experimental results find out the shape memory alloy Au30Cu25Zn45 that closely satisfy the cofactor conditions. Enhanced reversibility with thermal hysteresis of 2.045 degrees C, and the unusual riverine microstructure are found in Au30Cu25Zn45. However, their studies are limited to crystallographic analysis, and haven't provided enough details of microstructural evolution in martensitic transformation. Furthermore, it is the evolution of microstructures that leads to an extremely low thermal hysteresis in this alloy. Thus, making clear of evolution of microstructures in martensitic transformation in this alloy is of great importance. So, in the present work, the phase field method was applied, in which the microstructure is described by Landau theory of martensitic transformation, Khachaturyan-Shatalov's phase field microelasticity theory, and thermodynamics gradient to study the microstructural evolution of martensitic transformation in Au30Cu25Zn45, trying to figure out pathway of formation of the unusual microstructure with satisfying cofactor conditions. The simulation results show that during the martensitic transformation, quad-junctions composed of four different variants are formed. These junctions grow layer by layer, and the previously formed layer has larger size, thus leading to the formation of the experimentally reported "riverine" microstructure of martensite in Au30Cu25Zn45. Further analysis based on the crystallographic theory of martensitic transformation shows that in Au30Cu25Zn45 6 groups of variants can form such kind of quad-junction, and each group of variants can form 4 kinds of type 1/type 2 twin pairs and two kinds of compound twin pairs. All of the quad-junctions in this transformation are composed of four of those 6 twin pairs in each variant group, and the twin walls of these four twin pairs are perpendicular to each other.

Stabilization of martensite in cu-zn-ai alloy and its reverse shape memory effect

Stabilization of deformed stress-induced martensite and its effect on shape memory effect in an Fe-Mn-Si-Ni-Co alloy

Re-examination of martensitic stabilization in Cu-based shape memory alloys Part II. Key factors determining occurrence of martensitic stabilization in Cu-based alloys

Modulus Softening During the Γ→ɛ Martensitic Transformation in Fe–25Mn–6Si–5Cr–0.14N Alloys

Re-examination of martensitic stabilization in Cu-based shape memory alloys Part I. Identification of occurrence stage and degree of martensitic stabilization in CuZnAl alloys

Study of the stabilization of ordered austenite β1 in Cu79Al19X2 (X = Be or Mn) alloys

EFFECT OF MARTENSITE ORDERING ON SME IN A Cu-Zn-Al ALLOY

Failure mechanism of reverse shape memory effect in a Cu-base alloy

A Study of Structure of Metastable Cu–Zn Alloys with Shape Memory Effect

In Situ Observation of Thermoelastic Martensitic Transformation of Cu-Al-Mn Cryogenic Shape Memory Alloy with Compressive Stress

Effect of Cu content on martensitic transformation and shape memory behavior in Ti31.5Hf15Zr5Ni48.5−xCux alloys

Study of Stabilization of CuAlBe Alloy During Martensitic Transformation by Internal Friction

An in Situ Study on Austenite Memory and Austenitic Spontaneous Recrystallization of a Martensitic Steel

PHASE-FIELD MODELLING OF THE MARTENSITIC TRANSFORMATION IN SHAPE MEMORY ALLOY Au 30 Cu 25 Zn 45

Influence of Heat Treatment on Microstructures and Shape Memory Effect of Cu-28Zn-2.5Al wt. % Produced by Gravity Casting

Magnetic-Field-Induced Reverse Transformation in A Nicomnsn High Temperature Ferromagnetic Shape Memory Alloy

Structure and Martensitic Transformation in Rapidly Solidified CoNiAlFe Alloy

Time effect of martensitic transformation in Ni43Co7Mn41Sn9

Two-way shape memory effect induced by martensite deformation and stabilization of martensite in Ti36Ni49Hf15 high temperature shape memory alloy

Transformation Behavior And Shape Memory Effect Of A Coal Alloy

Fe–Mn–Si–Cr–Ni Based Shape Memory Alloy: Thermal and Stress-Induced Martensite