Study on the Lubrication Properties of Carbon Nanotubes

GU Daqiang

1998-01-01

Abstract:The Lubrication properties of the composite coat of Ni - P - Carbon nanotube on the 45# steel were investigated in this paper. The results obtained indicate that the composite coat of Ni - P - Carbon nanotube has a very high wear resistance and a very low friction coefficient. It is shown that the carbon nanotube is a kind of the very good solid lubricant.

What problem does this paper attempt to address?

Preparation and Tribological Properties of the Carbon Nanotubes–ni–p Composite Coating

Z. H. Li,X. Q. Wang,M. Wang,F. F. Wang,H. L. Ge

DOI: https://doi.org/10.1016/j.triboint.2005.10.001

IF: 5.62

2006-01-01

Tribology International

Abstract:A method to prepare the carbon nanotubes (CNTs)–Ni–P composite coating with different mass content of CNTs on the surface of 45# steel by electroless plating was proposed. The transmission electron microscopy (TEM) and the scanning electron microscopy (SEM) were used to observe the appearance of the as-prepared CNTs and the CNTs–Ni–P composite coating, and then the roughness of the coating surface was also analyzed by atomic force microscopy (AFM). Furthermore, the wear and friction behavior of the CNTs–Ni–P composite coating were investigated under oil-lubricated condition, Due to the self-lubrication property and the unique antifriction structure, CNTs can greatly improve the wear resistance of the CNTs–Ni–P composite coating, where the wear resistance of the CNTs–Ni–P composite coating is optimized with the intermediate mass content of 2kg/m3 CNTs.
SYNTHESIS AND THE PERFORMANCE OF CARBON NANOTUBES-(Ni-P) COMPOSITES

Xinqing Wang,Miao Wang,Zhenhua Li

2003-01-01

Abstract:The CNTs-(Ni-P) composites were prepared by electroless plating on 45~# steel substrate, and the optimum composition and operating conditions were obtained. The TEM was used to observe the CNTs' structure,the SEM was used to observe the appearance and distribution of the CNTs in the composites and the AFM(atomic force microscopy) was used to analyze the roughness status of the composite surface. The influence of the CNTs on the tribological performance of the composites is discussed. The results show that the CNTs-(Ni-P) composites have better wear-resistance than the uncoated substrate and the substrate coated with nikel.
Electroless Preparation and Tribological Properties of Ni-P-Carbon Nanotube Composite Coatings under Lubricated Condition

WX Chen,JP Tu,HY Gan,ZD Xu,QG Wang,JY Lee,ZL Liu,XB Zhang

DOI: https://doi.org/10.1016/s0257-8972(02)00408-5

2002-01-01

Abstract:Ni-P-Carbon nanotube (CNT) composite coatings as well as Ni-P-SiC and Ni-P-graphite coatings were prepared by electroless plating. The tribological properties of these composite coatings were investigated using a ring-on-block test rig under lubricated condition. The Ni-P-CNT composite coatings exhibited not only high wear resistance but also low friction coefficient compared with the Ni-P-SiC and Ni-P-graphite composite coatings. The favorable effects of CNTs on the tribological properties of the electroless coatings are attributed to improved mechanical properties and unique topological structure of the hollow nanotubes. In addition to preventing the rough contact between the two mating metal surfaces, the shorter CNTs can easily slide or roll within the surfaces of friction pairs. Therefore, the wear rate and friction coefficient of Ni-P-CNT composite coatings can be substantially reduced.
Tribological properties of Ni–P-multi-walled carbon nanotubes electroless composite coating

W.X Chen,J.P Tu,Z.D Xu,W.L Chen,X.B Zhang,D.H Cheng

DOI: https://doi.org/10.1016/S0167-577X(02)00968-0

IF: 3

2003-01-01

Materials Letters

Abstract:Carbon nanotubes (CNTs) have super-strong mechanical characteristics and unique hollow nanotube structure and are believed as very ideal materials for fabricating the excellent composites. In this paper, tribological properties of Ni–P-CNTs composite coating prepared by electroless technique were investigated using a ring-on-block test rig. The results indicated that addition of CNTs would result in an increase in hardness of the composite coating. Due to reinforcement and reduced friction, the tribological properties of Ni–P-CNTs composite coating were greatly improved. The Ni–P-CNTs composite coating exhibited not only higher wear resistance but also lower friction coefficient than the Ni–P–SiC and Ni–P-graphite coatings. After treatment at 400 °C for 2 h, the wear resistance of the Ni–P-CNTs electroless composite coating improved because of the Ni3P precipitation in Ni-matrix.
Friction and wear behavior of Ni-based carbon nanotubes composite coatings

涂江平,邹同征,王浪云,陈卫祥,徐铸德,刘芙,张孝彬

DOI: https://doi.org/10.3785/j.issn.1008-973X.2004.07.029

2004-01-01

Abstract:Ni-based carbon nanotubes (CNTs) composite coatings were prepared by electroless plating. The surface morphology of the coatings was analyzed by a scanning electron microscope (SEM).The friction and wear behavior of the composite coatings were investigated using a pin-on-disk wear tester under dry sliding condition. The experimental results indicated that the carbon nanotubes were uniformly embedded the composite coatings, and the Ni-based CNTs composite coatings showed excellent wear resistance. Due to the self-lubrication of carbon nanotubes, the friction coefficient of the composite coatings decreased with the increasing volume fraction of carbon nanotubes.
Tribological Application of Carbon Nanotubes in a Metal-Based Composite Coating and Composites

WX Chen,JP Tu,LY Wang,HY Gan,ZD Xu,XB Zhang

DOI: https://doi.org/10.1016/s0008-6223(02)00265-8

IF: 10.9

2003-01-01

Carbon

Abstract:Ni–P–carbon nanotube (CNT) composite coating and carbon nanotube/copper matrix composites were prepared by electroless plating and powder metallurgy techniques, respectively. The effects of CNTs on the tribological properties of these composites were evaluated. The results demonstrated that the Ni–P–CNT electroless composite coating exhibited higher wear resistance and lower friction coefficient than Ni–P–SiC and Ni–P–graphite composite coatings. After annealing at 673 K for 2 h, the wear resistance of the Ni–P–CNT composite coating was improved. Carbon nanotube/copper matrix composites revealed a lower wear rate and friction coefficient compared with pure copper, and their wear rates and friction coefficients showed a decreasing trend with increasing volume fraction of CNTs within the range from 0 to 12 vol.% due to the effects of the reinforcement and reduced friction of CNTs. The favorable effects of CNTs on the tribological properties are attributed to improved mechanical properties and unique topological structure of the hollow nanotubes.
Influence on (Ni-P) Electroless Composite Plating with Carbon Nanotubes

王新庆,李振华,朱海滨,王幼文,何少龙,王淼

DOI: https://doi.org/10.3969/j.issn.1671-4776.2002.03.007

2002-01-01

Abstract:In this paper the technique and conditions of the synthesis of CNTs-Ni-P composite coating with electroless com posite plating have been studied.We also discussed the influence on the wear-re-sis tance and anti-corrasion of the Ni-P com posite coating with the CNTs .We found the best conditions to synthesize the CNTs-Ni-P composite coating from all above.At the same time after annealed in high temperature,the hardness of the composite coating has been observed.The SEM and the TEM were used to analyze the structure characters of the CNTs-Ni-P composite coating and the morphology of the CNTs respectively.
Preparation and Self-Lubricity Investigation of CNTs/Ni Composite Coatings under Severe Conditions

Haifeng Xue,Yan He,Chuanwei Zhang,Tianxiang Li,Le Gu,Yongzhen Gu,Lupeng Wu

DOI: https://doi.org/10.1016/j.triboint.2024.109728

IF: 5.62

2024-01-01

Tribology International

Abstract:Carbon nanotubes (CNTs) demonstrate the potential to improve the tribological properties of nanocomposite coatings. Herein, CNTs/Ni composite coatings were quickly fabricated by the direct current (DC) electrodeposition. The adhesion strength was estimated by the scratch test incorporation with an acoustic emissive signal. Much attention was paid on the self-lubricity of the CNTs/Ni composite coating under severe conditions. Results indicated that presence of CNTs enhanced the adhesion strength of the pure Ni coating. Notably, CNTs contributed towards 54.5% of friction reduction in comparison to the pure Ni coating at dry friction. The improvement of tribological properties was attributed to that under high contact stress the embedded CNTs were crushed to tiny lubricating particles and produced protective film on rubbing surfaces.
Preparation and Tribological Performances of Ni-P-multi-walled Carbon Nanotubes Composite Coatings

Meng Zhen-qiang,Li Xi-bin,Xiong Yong-jun,Zhan Jing

DOI: https://doi.org/10.1016/s1003-6326(11)61523-9

2012-01-01

Abstract:Multi-walled carbon nanotubes (MWNTs) were wet-milled in the presence of ammonia and cationic surfactant and then used as reinforcements to prepare Ni-P-MWNTs composite coatings by electroless plating. The tribological performances of the composite coatings under dry condition were investigated in comparison with 45 steel and conventional Ni-P coating. Micrographs show that short MWNTs with uniform length and open tips were obtained through the wet-milling process. The results of wear test reveal that the Ni-P-MWNTs composite coatings posses much better friction reduction and anti-wear performances when compared with 45 steel and Ni-P coating. Within the MWNTs content range of 0.74%–1.97%, the friction coefficient and the volume wear rate of the composite coatings decrease gradually and reach the minimum values of 0.08 and 6.22×10−15 m3/(N·m), respectively. The excellent tribological performances of the composite coatings can be attributed to the introduction of MWNTs, which play both roles of reinforcements and solid lubricant during the wear process.
Friction and Wear Behavior of Electroless Ni-Based Cnt Composite Coatings

LY Wang,JP Tu,WX Chen,YC Wang,XK Liu,C Olk,DH Cheng,XB Zhang

DOI: https://doi.org/10.1016/s0043-1648(03)00171-6

IF: 4.695

2003-01-01

Wear

Abstract:Ni-based carbon nanotube (CNT) composite coatings with different volume fraction (from 5 to 12vol.%) of CNTs were deposited on medium carbon steel substrates by electroless plating. The friction and wear behavior of the composite coatings were investigated using a pin-on-disk wear tester under unlubricated condition. Friction and wear tests were conducted at a sliding speed of 0.0623ms−1 and at an applied load of 20N. The experimental results indicated that the friction coefficient of the composite coatings decreased with increasing the volume fraction of CNTs due to self-lubrication and unique topological structure of CNTs. Within the range of volume fraction of CNTs from 0 to 11.2%, the wear rate of the composite coatings showed a steadily decreasing trend with increasing volume fraction of CNTs. Because of the conglomeration of CNTs in the matrix, however, the wear rate of the composite coatings increased with further increasing the volume fraction of CNTs.
Friction and Wear Behavior of Electroless Wear-Resistant and Self-Lubricating Ni-P Composite Coatings

韩贵,陈卫祥,夏军宝,何新波,徐铸德,汪久根,涂江平

DOI: https://doi.org/10.3321/j.issn:1004-0595.2004.03.006

2004-01-01

Abstract:Ni-P-carbon nanotubes (Ni-P-CNTs) and Ni-P-inorganic fullerene-like WS2 (Ni-P-(IF-WS2)) composite coatings were prepared by electroless plating. The morphologies and microstructures of the CNTs and IF-WS2 nanoparticles were analyzed by means of scanning electron microscopy, transmittance electron microscopy and X-ray diffraction, while the phase structure and the composition of the resulting composite coatings were characterized by means of X-ray diffraction and elemental analysis. The friction and wear behaviors of the self-mated pairs of the resulting composite coatings were investigated on an MHK-500 ring-on-block friction and wear tester under the lubrication of a machine oil. It was found that the electroless Ni-P-CNTs and Ni-P-(IF-WS2) composite coatings recorded much better friction-reducing and antiwear properties than the Ni-P and Ni-P-graphite coatings. The significant improvement in the tribological properties of the Ni-P-CNTs was attributed to the excellent reinforcing effect and self-lubricity of the CNTs of coaxial graphitic nanotube structures. In a similar manner, the nested hollow inorganic fullerene-like structure of IF-WS2 nanoparticles and its rolling effect during the friction process accounted for the excellent tribological performance of Ni-P-(IF-WS2) composite coating.
Friction and wear behavior of Ni-P-carbon nanotubes (CNTs) electroless composite coating

Weixiang Chen,HaiYang Gan,Jiangping Tu,Wenlu Chen,Junbao Xia,Jiugen Wang,Zhude Xu,Guo Zhen Zhou

2002-01-01

Abstract:The Ni-P-CNTs composite coating as well as Ni-P-SiC and Ni-P-graphite coatings were prepared by electroless plating. The effect of heat treatment on the microstructure and tribological properties of the composite coatings was investigated. It was found that the Ni-P-CNTs composite coating exhibited higher wear resistance and lower friction coefficient than the other composite coatings such as Ni-P-SiC and Ni-P-graphite coatings. After treated at 673 K for 2 h, the wear resistance for all the composite coatings was improved. After heat treatment, the friction coefficient of other electroless coatings decreased, while the friction coefficient of the Ni-P-CNTs composite coating kept almost unchanged.
Friction and wear resistance of the electroless Ni-P-CNTs composite coatings

G. Zhao,H. Zhang,Z. Wang

DOI: https://doi.org/10.1117/12.780322

2007-01-01

Abstract:Ni-P-Carbon nanotubes (CNTs) composite coatings as well as Ni-P-SiC and Ni-P coatings were prepared by electroless plating. The characteristics of the coatings were assessed by scanning electron microscopy and microhardness test. The friction and wear performance of the produced composite coatings were investigated at room temperature on a ball-on-disc type tribometer under non-lubricated conditions. The results show that the Ni-P-CNTs composite coatings exhibited lowed friction coefficient and better anti-wear performance compared to Ni-P-SiC and Ni-P coatings due to improved mechanical properties, self-lubrication and unique microstructure of the Ni-P-CNTs composite coatings. The effect of CNTs on the friction and wear resistance was discussed in detail.
Effect of Carbon Nanotubes on Friction and Wear of a Piston Ring and Cylinder Liner System under Dry and Lubricated Conditions

Zhinan Zhang,Jun Liu,Tonghai Wu,Youbai Xie

DOI: https://doi.org/10.1007/s40544-016-0126-6

IF: 4.924

2017-01-01

Friction

Abstract:This study involves the application of carbon nanotubes (CNTs) to a piston ring and cylinder liner system in order to investigate their effect on friction and wear under dry and lubricated conditions. Carbon nanotubes were used as a solid lubricant and lubricant additive in dry and lubricated conditions, respectively. Simulation and measurement of friction and wear were conducted using a reciprocating tribometer. Surface analysis was performed using a scanning electron microscope and an energy dispersive spectrometer. The results indicate that carbon nanotubes can considerably improve the tribological performance of a piston ring and cylinder liner system under dry sliding conditions, whereas improvement under lubricated conditions is not obvious. Under dry friction, the effective time of the CNTs is limited and the friction coefficient decreases with an increase in CNT content. Furthermore, the dominant wear mechanism during dry friction is adhesive.
Tribological Behavior of Carbon-Nanotube-Filled PTFE Composites

W.X. Chen,F. Li,G. Han,J.B. Xia,L.Y. Wang,J.P. Tu,Z.D. Xu

DOI: https://doi.org/10.1023/A:1024869305259

2003-01-01

Tribology Letters

Abstract:Carbon nanotube/polytetrafluoroethylene (CNT/PTFE) composites with different volume fractions were prepared and their friction and wear properties were investigated using a ring-on-block under dry conditions. It was found that CNTs signifi-cantly increased the wear resistance of PTFE composites and decreased their coefficient of friction. PTFE composites with 15–20 vol.% CNTs exhibited very high wear resistance. The significant improvements in the tribological properties of CNT/PTFE composites are attributed to the super-strong mechanical properties and the very high aspect ratio of CNTs. The CNTs greatly reinforce the structure of the PTFE-based composites and thereby greatly reduce the adhesive and plough wear of CNT/PTFE composites. The CNTs are released from the composite during sliding and transferred to the interface of the friction couples. They thus serve as spacers, preventing direct contact between the mating surfaces and thereby reducing both wear rate and friction coefficient.
Investigation on Tribological Properties of Lubricating Oil with Carbon Nanotubes Additive

JIANG Peng,YAO Ke-fu

DOI: https://doi.org/10.3321/j.issn:1004-0595.2005.05.003

2005-01-01

Tribology

Abstract:Carbon nanotubes(CNTs), synthesized by catalytic decomposition of hydrocarbon gases method, can be well dispersed in lubricating oil when they were treated by ball milling. Effects of CNTs as an additive of commercial lubricating oil Great Wall SE 15W/30 on the friction and wear properties have been studied. Worn surface morphology was examined with scanning electron microscopy(SEM), and wear volume was measured with a Talysurf 5P-120 topographer. Results show that CNTs, in mass concentration of 0.01%~0.1%, can greatly improve the antiwear ability of lubricating oil. With addition of CNTs, the maximum reduction of wear rate is about 57%, and scratches on the worn surfaces become slighter and more uniform. The maximum decrease of friction coefficient is about 15% with 0.025% CNTs additive at the load of 300 N. The antiwear mechanism has been discussed.
Preparation and properties of Ni/P/single-walled carbon nanotubes composite coatings by means of electroless plating

Zhi Yang,Hui Xu,Meng-Ke Li,Yan-Li Shi,Yi Huang,Hu-Lin Li

DOI: https://doi.org/10.1016/j.tsf.2004.02.016

IF: 2.1

2004-01-01

Thin Solid Films

Abstract:Ni/P/single-walled carbon nanotubes (SWNTs) composite coatings as well as Ni/P coating have been prepared successfully by electroless plating technique. The tribological properties of the composite coatings were investigated by a friction and wear tester. Comparing with Ni/P coating, Ni/P/SWNTs composite coatings showed not only higher wear resistance but also lower friction coefficient. The electrochemical properties of the composite coatings were studied using electrochemical workstation system. The corrosion behavior of the composite coatings was evaluated by polarization curves in 0.1 M NaCl solution at room temperature. It was noted that the amorphous Ni/P/SWNTs composite coatings provided higher corrosion resistance than the amorphous Ni/P coating.
Effect of Multi-Walled Carbon Nanotubes on Tribological Properties of Lubricant

CS Chen,XH Chen,JM Hu,H Zhang,WH Li,LS Xu,Z Yang

IF: 3.752

2005-01-01

Transactions of Nonferrous Metals Society of China

Abstract:After purified by mixture of sulfuric acid and nitric acid, the multi-walled carbon nanotubes(MWNTs)were modified with stearic acid(SA). The modified carbon nanotubes as lubricant additive were utilized to prepare lubricant, and the effects of carbon nanotubes on the tribological properties were investigated by using a pin-on-plate wear tester. The surface structure of MWNTs was examined by transmission electron microscopy, Raman spectroscopy and infrared spectroscopy. The results show that the surfaces of MWNTs are coated with a modified layer of SA. Furthermore, the modified MWNTs as lubricant additive can effectively improve the friction-reduction and antiwear ability of lubricant. The friction coefficient of base lubricant decreases by about 10% and the wear loss of base lubricant decreases by 30%-40% when the concentration of modified MWNTs in lubricant is 0.45%. In addition,the mass ratio of SA to MWNTs influences the friction-reduction and anti-wear ability of the modified MWNTs as lubricant additive. The optimum mass ratio of MWNTs to stearic acid is about 3: 8 - 1 : 2.
A Study on Mechanism of Tribological Behavior of Carbon Nanotubes

Li Rui,Hu Yuanzhong,Wang Hui

DOI: https://doi.org/10.4028/www.scientific.net/amr.306-307.1444

2011-01-01

Abstract:This paper investigates mechanism of tribological behavior of carbon nanotubes by using universal tribometer-II and molecular dynamics simulations. The experiment results indicate that multi-walled carbon nanotubes film with mixed acid treatment has better surface quality and less impurities but higher friction than pristine carbon nanotubes film. The reason is that mixed acid treatment introduces carboxyl group and more defects which increases dangling bonds of carbon nanotubes. Breaking of dangling bonds increases friction force when sliding and shearing occurs. Molecular dynamics simulation of shearing between silicon surfaces and single-walled carbon nanotube bundles without defect shows low lateral forces because only van der walls force exists between silicon surfaces and carbon nanotubes owing to no dangling bonds. The result is consistent to the conclusion inferred from experiment. Therefore excellent performance is expected when carbon nanotubes treated with little defects are used as lubricant or addictives.
Study of the tribological properties of carbon nanotubes filled PTFE composites

夏军宝,陈卫祥,李飞,韩贵,王浪云,涂江平,徐铸德

DOI: https://doi.org/10.3785/j.issn.1008-973X.2003.04.020

2003-01-01

Abstract:The friction and wear properties of CNTs filled PTFE composites with different filler proportions in sliding against stainless steel ring under dry friction conditions were studied. Experimental results showed that CNTs could decrease the friction coefficient of PTFE composites with the increase of filler content. The anti-wear property of PTFE composite was significantly enhanced by filling CNTs in PTFE and the best volume fraction of CNTs was 15%-20%. SEM cross-sectional micrographs of pure PTFE and CNTs/PTFE composite showed that fiber structures existed in pure PTFE, and did not exist in CNTs/PTFE composite, indicating that CNTs filler could dramatically retard the destruction of the PTFE structures. It can be seen from the SEM images of the worn surfaces of pure PTFE and CNTs/PTFE composite that some obvious ploughing and adhesion marks on the pure PTFE worn surface, while the CNTs/PTFE composite worn surface was very smooth. The fact indicates that the CNTs filler can dramatically reduce the wear of PTFE composites.

Study on the Lubrication Properties of Carbon Nanotubes

Preparation and Tribological Properties of the Carbon Nanotubes–ni–p Composite Coating

SYNTHESIS AND THE PERFORMANCE OF CARBON NANOTUBES-(Ni-P) COMPOSITES

Electroless Preparation and Tribological Properties of Ni-P-Carbon Nanotube Composite Coatings under Lubricated Condition

Tribological properties of Ni–P-multi-walled carbon nanotubes electroless composite coating

Friction and wear behavior of Ni-based carbon nanotubes composite coatings

Tribological Application of Carbon Nanotubes in a Metal-Based Composite Coating and Composites

Influence on (Ni-P) Electroless Composite Plating with Carbon Nanotubes

Preparation and Self-Lubricity Investigation of CNTs/Ni Composite Coatings under Severe Conditions

Preparation and Tribological Performances of Ni-P-multi-walled Carbon Nanotubes Composite Coatings

Friction and Wear Behavior of Electroless Ni-Based Cnt Composite Coatings

Friction and Wear Behavior of Electroless Wear-Resistant and Self-Lubricating Ni-P Composite Coatings

Friction and wear behavior of Ni-P-carbon nanotubes (CNTs) electroless composite coating

Friction and wear resistance of the electroless Ni-P-CNTs composite coatings

Effect of Carbon Nanotubes on Friction and Wear of a Piston Ring and Cylinder Liner System under Dry and Lubricated Conditions

Tribological Behavior of Carbon-Nanotube-Filled PTFE Composites

Investigation on Tribological Properties of Lubricating Oil with Carbon Nanotubes Additive

Preparation and properties of Ni/P/single-walled carbon nanotubes composite coatings by means of electroless plating

Effect of Multi-Walled Carbon Nanotubes on Tribological Properties of Lubricant

A Study on Mechanism of Tribological Behavior of Carbon Nanotubes

Study of the tribological properties of carbon nanotubes filled PTFE composites