Abstract:Traditional TiN coatings cannot meet the requirements in many applications under extreme conditions because of their relatively low hardness (similar to2000Hv), high friction coefficient (>0.4), inade- quate thermal stability and insufficient corrosion. (Ti,Al)N coatings are a promising alternative to TiN coatings, which have recently been obtained by some groups. However, The deposition of coatings on ceramic substrates prepared by traditional physical vapor deposition was puzzled by low adhesions. In this work, (Ti,Al)N deposition was realized by a new technique namely pulsed high energy density plasma. The ratio of Ti and Al atoms was kept constant at 1:1, since this was known to be the best ratio for (Ti,Al)N synthesis. However, the process allows many other deposition parameters to be varied. In this study, the influences of the discharge voltage between the inner and outer electrode, the distance between the sample and the pulsed plasma gun, and the shot number of the pulsed plasma on coating formation and properties were investigated. Under the optimum deposition conditions, the adhesive strength of (Ti,Al)N coating to Si3N4 ceramic substrate was satisfactory with the critical load up to more than 80 mN. In addition, the coatings were investigated with respect to mechanical and wear behavior, including nanohardness, Young's modulus and cutting performances. The (Ti,Al)N coatings possess resulted very high values of nanohardness and Young's modulus, which are near to 40 GPa and 680 GPa, respectively. Because of the deposition of (Ti,Al)N coatings the wear resistance and edge life of the coated tools were improved dramatically evaluated by the cutting perforinances of the coated tools in turning HT250 (HB230) steel under industrial conditions. These improvements were attributed to a combination of four effects of deposition, ion implantation, quench and solid solution strengthening in terms of the structural analyses.

OBTAINING OF TiN COATING ON CERAMIC PARTICLES AND ITS USE

Preparation of Ultra-Fine ATC Ceramics and Analysis of Its Dry-Sliding Wear Behavior

Growth behavior of CVD Ti(C,N,O) coating on cemented carbide controlled by CO and the mechanism

Film Coating Process Research and Characterization of TiN Coated Racetrack-type Ceramic Pipe

PREPARATION AND CHARACTERIZATION OF CaZrO3 COATING ON GRAPHITE FOR TiNi ALLOY MELTING

Study on the growth and wear behavior of the TiAlN-based composite coating deposited on TiCN-based cermets with different binder phase

Investigations on microstructure, mechanical and tribological properties of TiN coatings deposited on three different tool materials

Preparation of NiTi-Cr3C2/Nano-TiC Coating and Its Properties

Characterization of Superhard Ternary (ti,al)n Coatings Prepared by Pulsed High Energy Density Plasma

Characterization of Surface Properties of TiC Ceramic Coating Developed on AISI 1020 Steel

Study on the growth and wear characters of CVD coating deposited on Ti(C, N)-based cermets with adding different C/N ratios of Ti(C, N) powders

Preparation, mechanical properties and wear resistance of dual-sized TiC particles reinforced high-entropy alloy cermet coating

Study on the preparation of hard and wear-resistant titanium nitride films on silicon nitride ceramic cutting tools

Formation mechanism of the TiN containing coating on the Al2O3-Ti2O3 composite at 1400°C nitrogen-blowing

Preparation and Properties of Composite Nanoceramic NiCrBSi-TiO2/WC(Co) Coatings

TiC nano-coating and their tribological properties were deposited by doal-ion beam sputtering on the tool surface

In Situ Formation of Tic Particulate Composite Coating with A Gradient Distribution by Laser Cladding

High Temperature Decomposition Behavior of CaZrO3 Coating on Graphite for TiNi Alloy Melting

Introduction of heavy micro titanium carbide particles into Zn‐Ni coatings on steel during in‐situ brush electroplating

Combustion synthesis of Al2O3 ceramic coating and its application

In Situ Synthesis of (M:Nb,Ta)C/Ni35 Composite Coating Cladded on 40Cr Steel