Abstract:Traditional TiN coatings cannot meet the requirements in many applications under extreme conditions because of their relatively low hardness (similar to2000Hv), high friction coefficient (>0.4), inade- quate thermal stability and insufficient corrosion. (Ti,Al)N coatings are a promising alternative to TiN coatings, which have recently been obtained by some groups. However, The deposition of coatings on ceramic substrates prepared by traditional physical vapor deposition was puzzled by low adhesions. In this work, (Ti,Al)N deposition was realized by a new technique namely pulsed high energy density plasma. The ratio of Ti and Al atoms was kept constant at 1:1, since this was known to be the best ratio for (Ti,Al)N synthesis. However, the process allows many other deposition parameters to be varied. In this study, the influences of the discharge voltage between the inner and outer electrode, the distance between the sample and the pulsed plasma gun, and the shot number of the pulsed plasma on coating formation and properties were investigated. Under the optimum deposition conditions, the adhesive strength of (Ti,Al)N coating to Si3N4 ceramic substrate was satisfactory with the critical load up to more than 80 mN. In addition, the coatings were investigated with respect to mechanical and wear behavior, including nanohardness, Young's modulus and cutting performances. The (Ti,Al)N coatings possess resulted very high values of nanohardness and Young's modulus, which are near to 40 GPa and 680 GPa, respectively. Because of the deposition of (Ti,Al)N coatings the wear resistance and edge life of the coated tools were improved dramatically evaluated by the cutting perforinances of the coated tools in turning HT250 (HB230) steel under industrial conditions. These improvements were attributed to a combination of four effects of deposition, ion implantation, quench and solid solution strengthening in terms of the structural analyses.

Study on the preparation of hard and wear-resistant titanium nitride films on silicon nitride ceramic cutting tools

HARD AND WEAR-RESISTANT TITANIUM NITRIDE COATINGS DEPOSITED BY PULSED HIGH ENERGY DENSITY PLASMA FOR CUTTING TOOLS

Microstructure and Mechanical Properties of Titanium Nitride Coatings for Cemented Carbide Cutting Tools by Pulsed High Energy Density Plasma

New Process for Improving Silicon Nitride Cutting Tools: Coating by Pulsed High Energy Density Plasma

Structure of the Coatings Onto Ceramic Cutting Tools Deposited by Pulsed High Energy Density Plasma

Nanometer Grain Titanium Carbonitride Coatings with Continuously Graded Interface Onto Silicon Nitride Cutting Tools by Pulsed High Energy Density Plasma

Ti(C,N) Hard Coatings Prepared by Pulsed High Energy Density Plasma

Characterization of Superhard Ternary (ti,al)n Coatings Prepared by Pulsed High Energy Density Plasma

Wear‐Resistant Titanium Carbonitride Coatings Onto WC–Co Cutting Tools by Pulsed High‐Energy Density Plasma

Investigations on microstructure, mechanical and tribological properties of TiN coatings deposited on three different tool materials

Progress of Surface Modification for Ceramic Cutting Tools by Pulsed High Energy Density Plasma

Machining Performance of Sputter-Deposited (al0.34cr0.22nb0.11si0.11ti0.22)50n50 High-Entropy Nitride Coatings

High Temperature Wear Behavior of Titanium Nitride Coating Deposited Using High Power Impulse Magnetron Sputtering

Microstructure, Mechanical Properties, and Oxidation Resistance of Nanocomposite Ti–Si–N Coatings

Tribological Properties and Preparation of (Ti,Al)N Coatings on High Speed Steel Substrate

Comparative analysis over microstructural, mechanical properties and cutting performance of TiN, TiVN coatings deposited by magnetron sputtering on SiAlON ceramic tool insert

On wear of TiAlN coated tools with and without NbN overlayer in machining titanium alloys

Properties and Performance of TiAlSiN and AlCrN Monolayer and Multilayer Coatings for Turning Ti-6Al-4V

Structural characterization and adhesion appraisal of TiN and TiCN coatings deposited by CAE-PVD technique on a new carbide composite cutting tool

Cutting Performance of TiN/TiSiN Coated Tool during Turning of Ti6Al4V Titanium Alloy

Microstructure and Properties of the AlCrSi(O)N Tool Coatings by Arc Ion Plating