Instantaneous detecting approach of harmonic voltage based on instantaneous reactive power theory

Weizheng Yao,Qun Wang,Jinjun Liu,Zhao'An Wang

1998-01-01

Abstract:An instantaneous detecting approach of harmonic voltage, based on instantaneous reactive power theory, is proposed. It has the advantages of fast response and accuracy, and can be easily implemented by electronic circuit. The feasibility of its application was verified experimentally.

What problem does this paper attempt to address?

Unified Model Based Harmonics and Reactive Current Detection

WANG Li-qiao,LIN Ping,LIU Zhao-shen,ZHANG Zhong-chao

DOI: https://doi.org/10.3785/j.issn.1008-973x.2005.05.019

2005-01-01

Abstract:A unified model for harmonics and reactive current closed-loop or open-loop detection was established based on instantaneous reactive power theory. The fundamental active currents were obtained by transforming the load currents into rotation coordinate system and filtering the high frequency component through an equivalent lowpass filter. Harmonics and reactive currents were acquired by subtracting the fundamental active currents from load currents. An optimum project was presented for the equivalent lowpass filter, and the effects of the rank and cutoff frequency of the filter on the dynamic and static features of the detection system were analyzed. Considering the performance of both dynamic and static response, the cutoff frequency should be 10—40 Hz. The rank should not exceed 3 for reducing the realization complexity. The experimental result of a realtime harmonics and reactive current closed-loop detection system applied to active power filter shows that this system has perfect dynamic and static response.
An Instantaneous Detecting Approach of Harmonic Voltage for the Series Active Power Filter

WZ Yao,Q Wang,JJ Liu,ZO Wang

DOI: https://doi.org/10.1109/icpst.1998.729344

1998-01-01

Abstract:In this paper, based on the instantaneous reactive power theory, an instantaneous detecting approach of harmonic voltage is proposed. It is discussed both theoretically and experimentally that the harmonic voltage can be obtained in real-time through detecting load voltage. The distinguishing points of the presented approach are its fast response and accuracy. It is convenient to implement by using analog multipliers, dividers and operational amplifiers. The experiment results verify the correctness and feasibility of the proposed approach, and it can be used for active power filters to compensate power system harmonics
Novel Method for Detecting Synchronous Phases and Instantaneous Symmetrical Components

CHEN Hai-rong,ZHANG Jing,PAN Wu-lue

2009-01-01

Abstract:Under AC power system fault conditions,detecting synchronous phase and instantaneous symmetrical components quickly and accurately is an important part of the control and protection system of voltage source inverter (VSI) based FACTS(Flexible AC Transmission).Consequently,based on the analysis of the working principle of phase lock loop (PLL) and the influence of negative sequence voltage components on the PLL’s detecting performance,a novel integrated method for detecting synchronous phase and instantaneous symmetrical components was proposed. A feed-forward voltage compensating method based on dual synchronous frame was adopted in the method,q axis component of the fundamental positive voltage was used as input of the PLL and the output of PLL was used as reference phase of synchronous frame transform. Moreover,the implementation mechanism of the proposed method was analyzed,and the block diagram of the detecting circuit is given and verified by experimental research. Experimental results show that the proposed method can not only detect synchronous phase and instantaneous symmetrical components accurately under unbalanced source voltage but also eliminate the influence of frequency diversification on detecting synchronous phase and instantaneous symmetrical components.
An Improved Algorithm for Harmonic Detection of Power System Using Adaptive Notch Filter

Zhengjie XU,Zhengshi WANG

DOI: https://doi.org/10.13234/j.issn.2095-2805.2015.4.64

2015-01-01

Abstract:The wide use of nonlinear power electronic equipment brings out serious harmonic pollution in grid. Restricting harmonic pollution becomes an urgent problem to be solved. The key to restrict and compensate harmonic is to detect harmonic accurately and timely. Firstly, the effect of direct component and changed amplitude on harmonic detection using adaptive notch filter is amalyzed, and a modified adaptive notch filter is designed. Then modified adaptive notch filter can accurately extract direct component, fundamental frequency, harmonic instantaneous value and amplitude when grid includes direct component and changes amplitude. The result of Matlab/Simulink simulation shows that the above-mentioned approach is effective.
A Digital Method for Detecting Harmonic Currents Based on Instantaneous Reactive Power Theory

He Yingjie,Liu Jinjun,Zou Yunping

DOI: https://doi.org/10.3969/j.issn.1000-6753.2010.08.029

2010-01-01

Abstract:The choice of the cut-off frequency reflects a tradeoff between maladjustment and the speed of dynamic response in the conventional detection method based on instantaneous reactive power theory. The paper proposes a novel digital real-time algorithm for detecting harmonic currents. This algorithm adopts a new variable step size least mean square(LMS) adaptive filter as LPF on harmonic detection circuit. The step-size is large when the algorithm is far from the optimum with decreasing as it approaches the optimum. The proposed algorithm allows more flexible control of misadjustment and fast convergence rate without the need to compromise one for the other. Meanwhile approximate theoretical expressions for the behavior of the algorithm are derived. The additional calculation is very little,so the algorithm presented is easy to implement. Simulation and experiment results illustrate that the performance of the proposed approach is satisfactory.
Harmonic and Reactive Current Synchronous Detecting Method Based on DSP

HUANG Feng,ZHAO Guang-zhou

DOI: https://doi.org/10.3969/j.issn.1671-7147.2007.02.010

2007-01-01

Abstract:Limitations of the conventional synchronous detecting method for reactive and harmonic currents in case of unbalanced or distorted three-phase voltages is discussed.Then,an advanced method is proposed to replace the phase voltage by fundamental positive-sequence voltage.Taking accout of the speediness and stability,it was carried out by TMS320VC5402 Digital Signal Processor(DSP).It can be fast and accurately detect the sum of fundamental reactive current,unbalanced components and harmonics.The theoretical analysis and simulation verify the feasibility of this method.
A NEW METHOD FOR REAL-TIME DETECTING HARMONICS AND REACTIVE CURRENTS IN SINGLE-PHASE CIRCUIT

Jiang Bin,Yan Gangfeng,Zhao Guangzhou

DOI: https://doi.org/10.3321/j.issn:1000-1026.2000.21.009

2000-01-01

Abstract:In order to simplify the detection of harmonics and instantaneous reactive currents in single-phase circuit, the current in single-phase circuit is decomposed and a new method for such a purpose is proposed. Firstly, the single-phase current is multiplied by unit sinusoidal and cosinoidal signals with the same frequency of that of circuit voltage respectively and then sent to two low pass filters. Secondly, the outputs of these two low pass filters are again multiplied by the unit sinusoidal and cosinoidal signals to get the reactive and active currents. Lastly, by subtracting the active current thus obtained from the original current, the harmonics and reactive currents can be detected. The function of phase lock loop (PLL) in this method is analyzed in detail and the preconditions of simplifying the algorithm by omitting it are presented. Simulation and experimental results show that harmonics and instantaneous reactive currents in single-phase circuit can easily be precisely detected in real-time by using this simple method.
Use Hamming Window for Detection the Harmonic Current Based on Instantaneous Reactive Power Theory

F Zhuo,SS Choi,C Chen,YH He,ZA Wang

2004-01-01

Abstract:This paper proposes a new digital real-time method for accurate detection of harmonic current. This method was modified from a well-known technique that is based on the instantaneous reactive power theory. Using complex integral algorithm and employing Hamming windowing to suppress spectral leakage, it was proven to improve the detection precision significantly. It not only measures the total harmonic current, but is also able to differentiate between positive-sequence and negative-sequence components of each harmonic. The capability of this method has been verified via computer simulations as well as through its application in a 30-kVA active filter prototype.
Single Order Harmonic Detection with Incremental Algorithm of DFT

Tong Xiangqian,Shen Ming,Yin Jun,Li Mu

DOI: https://doi.org/10.1109/ipemc.2009.5157806

2009-01-01

Abstract:To extract a single order harmonic component from single phase voltage or current is a difficult work by the existed instantaneous reactive power theory, which is dominant in the detection of the total harmonic components in three-phase system. A novel detection approach of single order harmonic in single-phase system based on discrete Fourier transformation with smooth moving window is discussed in this paper, and an incremental algorithm is presented to improve the dynamic response. Both simulation and experimental results show that the approach has the advantages of high accuracy and rapid response, and it can satisfy the requirement of active power filter for harmonic mitigation.
A Fast And Accurate Detection Method Of Instantaneous Reactive Current In Single-Phase Power System

Xiaokang Liu,Liansong Xiong,Fang Zhuo,Ying Chen,Minghua Zhu

DOI: https://doi.org/10.1109/icpe.2015.7168051

2015-01-01

Abstract:Fast and accurate detection of instantaneous reactive current in single-phase power system is a pre-requisite for the precise control of STATCOM (Static Synchronous Compensator). A major solution is based on the construction of virtual orthogonal signal in rotational coordinate transformation; however, conventional methods show weaknesses in the speed of detection and the ability of noise and harmonic suppression. In this paper, a novel method of instantaneous reactive current detection in single-phase system, with fast and accurate property as well as harmonic and noise susceptibility, is proposed. Firstly, a novel virtual orthogonal signal generation algorithm is deduced, remarkably improving the immediacy and precision of detection in synchronous reference frame. Then an enhanced moving average filter (EMAF) is utilized in cascade and its design principle is proposed, sufficiently eliminating the effects of noise and harmonics. Finally, experiments reveal that the proposed detection scheme can achieve the satisfactory control goals.
Delayless Harmonic Detection Based on DSP with High-Accuracy for Active Power Filter

Z Chen,DH Xu

DOI: https://doi.org/10.1109/apec.2005.1453296

2005-01-01

Abstract:This paper presents a delayless harmonic detection system based on DSP with high-accuracy for active power filter. Modified structure adopting new signal-flow is introduced, which can effectively integrate analog control and digital control. Phase-shift compensating strategy is introduced into the synchronous-reference-frame based detection algorithm to overcome time-delay induced by digital control. Some design issues such as evaluation of time delay and digital phase shift is discussed. Furthermore, to guarantee satisfactory detecting performance, low sampling rate based low pass filter design helps to realize accurate fundamental current extraction overcoming the limitation of certain DSP resource. Experimental results verify the excellent performance of the presented harmonic detection system.
A Harmonic Current Detection Method Based on Digital Signal Processing Technology

YH He,JJ Liu,ZA Wang

2004-01-01

Abstract:According to digital signal processing technology, the digital algorithm for the instantaneous reactive power theory is discussed. The real-time detection approach of harmonic current based on it is proposed and the corresponding detection system including DSP is configured The simulation and the experiment investigations aiming at the detection system are done to show the performance of the detection system.
Digital Realization of A Novel Detection Algorithm Based on Instantaneous Reactive Power Theory

Yingjie He,Yunping Zou,Jian Tang,Yun Xu

DOI: https://doi.org/10.1109/iecon.2007.4460010

2007-01-01

Abstract:An active power filter(APF) is an effective method controlling harmonic perturbations. Obviously, fast and precise harmonic detecting is one of the keys to design APFs. The paper thoroughly researches instantaneous reactive power theory and proposes a new variable step size least mean square(LMS) adaptive filter as the low pass filter(LPF) on harmonic detection circuit , where the step size of the algorithm is adjusted according to the square of the time-averaged estimate of the autocorrelation of e(n) and e(n-1). As a result, the algorithm can effectively adjust the step size while maintaining the immunity against harmonic current disturbance. The proposed algorithm allows more flexible control of misadjustment and fast convergence rate without the need to compromise one for the other. Simulation and experiment results illustrate that the performance of the proposed approach is satisfactory.
An Improved Algorithm for Harmonic Current Detection Based on Instantaneous Reactive Power Theory

HE Ying-jie,ZOU Yun-ping,HUANG Zhu,ZHANG Yu-cheng

DOI: https://doi.org/10.3321/j.issn:1000-3673.2007.06.014

2007-01-01

Abstract:Fast and precise detection of harmonic currents is the key factor that determines the integrative filtering performance of active power filter(APF).An improved harmonic detection algorithm based on the instantaneous reactive power theory is proposed,in which a new variable step length least mean square(LMS) adaptive filter is used as the low-pass filter in the detection circuit.By means of choosing the parameters of recurrence formula and the autocorrelation estimation of two error signals,the step length can be effectively adjusted,furthermore,the convergence rate and misadjustment can be controlled more flexibly.The theoretical analysis and simulation experiment prove that the proposed harmonic current detection algorithm is correct and effective.
An Improved Harmonic Energy Measurement Algorithm Based on Instantaneous Reactive Power Theory

He-long Li,Xiao-lei Yuan,Zhi-bin Zheng,Jin-quan Zhao

DOI: https://doi.org/10.1007/978-3-030-32591-6_62

2019-01-01

Abstract:Aiming at the unreasonable phenomenon that the different harmonic power will be cancelled out in the current harmonic background, a harmonic energy measurement algorithm is proposed to improve the instantaneous reactive power. First, the three-phase voltage and current signals are constructed by the delay of single-phase voltage and current signals. Then by changing the rotational speed of the p-q coordinate system in the instantaneous reactive power theory, the signals of different frequency harmonics in the voltage and current are obtained after filtering. Finally, the active power and reactive power of the system are obtained by the power conversion. This method can not only measure the power in positive and backward separately, but also avoid the unreasonable phenomenon of the positive and reverse power offset when the electric energy is measured, and can be used in the single phase system and the three-phase system. Finally, the simulation results of Matlab verify the effectiveness and accuracy of the proposed method.
Electric Energy Measurement Based on the Improved Instantaneous Reactive Power Theory.

Jian-Hua Yin,Xiao-Ke Chen,Zhi-Bin Zheng,Jian-Zhi Liu,Jin-Quan Zhao

DOI: https://doi.org/10.1109/FSKD.2018.8686899

2018-01-01

Abstract:In this paper, a method of electric energy measurement based on the instantaneous reactive power theory is put forward according to the deficiency that power under different frequencies will be offset at the same time under the nonsinusoidal and unbalanced condition. By changing the rotation direction and velocity of the p-q coordinate system in the generalized three-phase instantaneous reactive power theory, we can obtain the positive and negative sequence voltage and current of any harmonic in the three-phase three-line system. Then the positive and negative sequence power can be converted to phase power, thus the system power under non-sinusoidal and unbalanced condition is obtained. The suggested method can calculate the power of different harmonics, avoiding the unreasonable phenomena of power under different frequencies be offset, and the calculation of this method is small and the calculation accuracy is high. Finally, the method is validated by Matlab simulation.
Instantaneous Reactive Power Theory and Its Applications in Detection of Reactive Power in SVC

Lian Zhifeng,Chen Ying,Huang Zhenhua

2007-01-01

Abstract:The traditional methods based on definitions of reactive power can not fulfill the demand,so the paper employs the instantane- ous reactive power theory to detect the reactive power in SVC system.The paper analyses the principle of instantancous reactive power theory,and deduces the formula to calculate the instantaneous reactive power in SVC system,and employs a sliding window to calculate the average reactive power.The paper applies the new method by simulation,the results of which show that the method is efficient in detecting reactive power in SVC system and thus provides application in designing the monitor and control system of SVC.
EFFECT OF HIGH PASS FILTER ON DETECTING EFFECTIVENESS OF HARMONICS DETECTION CIRCUIT

Wang Qun,Yao Weizheng,Wang Zhaoan

DOI: https://doi.org/10.3321/j.issn:1000-1026.1999.16.005

1999-01-01

Abstract:An approach of detecting harmonic currents based on the instantaneous reactive power theory is analyzed. Its corresponding simulation circuit is built by MATLAB simulation software. The simulation studies about the influence of the high pass filters in the detection circuit on the effectiveness of detection are carried out. The results show that the dynamic response and the detecting precision can greatly be influenced by the cut-off frequency, the order and the type of the high pass filter. The conclusions can provide guidance for designing harmonics detection circuits.
Digital detection methods and application of harmonics and inter-harmonics in power grid

Bin Chen,Wenjia Xu,Xin Lu,Yong Xiao,Wei Zhao,Songling Huang

DOI: https://doi.org/10.3969/j.issn.1001-1390.2014.24.010

2014-01-01

Abstract:Real-time accurate detection of the harmonics and inter-harmonics in power grid becomes increasingly prominent.In this paper, the methods for harmonic analysis are divided into two parts according to their application to detect stationary or non-stationary signals.Various methods and their characteristics, such-as Fourier transform, wave-let transform, S-transform, artificial neural network, spectrum estimation and Hilbert-Huang transform are discussed in details.Finally, the paper provides a summary and outlook for all the detection methods.
A New Algorithm for Harmonic Detection and Comparison with Other Algorithms

YAN Zhao-yang,ZHU Gui-ping

DOI: https://doi.org/10.3969/j.issn.1008-0686.2012.05.013

2012-01-01

Abstract:This paper proved that the instantaneous reactive power theory is essentially an orthogonal transformation and inverse transform in a 3-dimensional time-variant vector space by detailed mathematical deduction.With different orthogonal vectors,the theory can detect active or reactive current of any order and any sequence.Compared with traditional FFT algorithm,they are consistent in mathematical essence.The difference between the low-pass filter and the integrator results in their different real-time performance.Finally an improved FFT algorithm with low-pass filter is proposed in the paper.

Instantaneous detecting approach of harmonic voltage based on instantaneous reactive power theory

Unified Model Based Harmonics and Reactive Current Detection

An Instantaneous Detecting Approach of Harmonic Voltage for the Series Active Power Filter

Novel Method for Detecting Synchronous Phases and Instantaneous Symmetrical Components

An Improved Algorithm for Harmonic Detection of Power System Using Adaptive Notch Filter

A Digital Method for Detecting Harmonic Currents Based on Instantaneous Reactive Power Theory

Harmonic and Reactive Current Synchronous Detecting Method Based on DSP

A NEW METHOD FOR REAL-TIME DETECTING HARMONICS AND REACTIVE CURRENTS IN SINGLE-PHASE CIRCUIT

Use Hamming Window for Detection the Harmonic Current Based on Instantaneous Reactive Power Theory

Single Order Harmonic Detection with Incremental Algorithm of DFT

A Fast And Accurate Detection Method Of Instantaneous Reactive Current In Single-Phase Power System

Delayless Harmonic Detection Based on DSP with High-Accuracy for Active Power Filter

A Harmonic Current Detection Method Based on Digital Signal Processing Technology

Digital Realization of A Novel Detection Algorithm Based on Instantaneous Reactive Power Theory

An Improved Algorithm for Harmonic Current Detection Based on Instantaneous Reactive Power Theory

An Improved Harmonic Energy Measurement Algorithm Based on Instantaneous Reactive Power Theory

Electric Energy Measurement Based on the Improved Instantaneous Reactive Power Theory.

Instantaneous Reactive Power Theory and Its Applications in Detection of Reactive Power in SVC

EFFECT OF HIGH PASS FILTER ON DETECTING EFFECTIVENESS OF HARMONICS DETECTION CIRCUIT

Digital detection methods and application of harmonics and inter-harmonics in power grid

A New Algorithm for Harmonic Detection and Comparison with Other Algorithms