Abstract:In this experiment, Ce is used to treat nonquenched and tempered steel F38MnVS. It is found that the addition of Ce forms considerable Ce‐containing inclusions, which improves the morphology of inclusions. At the same time, Ce‐containing inclusions promote the refinement of austenite and ferrite. Various techniques, such as optical microscopy, high‐temperature confocal laser scanning microscopy, scanning electron microscopy, electron backscatter diffraction, and thermodynamic calculations, are employed to analyze the optimization mechanism of Ce on the inclusions and microstructures in F38MnVS as‐cast samples. The results show that the addition of Ce inhibits MnS precipitation at the grain boundaries and significantly reduces the diameters and aspect ratios of the inclusions. After Ce treatment, a new type of composite inclusion appears in the steel. The modification of the inclusions by Ce promotes the optimization of the as‐cast microstructure during solidification, which mainly exhibits austenite grain refinement and polygonal ferrite formation in the grains. Based on the misfit degree theory, the refinement of the austenite grains is because of the nucleation of austenite grains facilitated by Ce2O2S and CeAlO3. The increased nucleation of the intragranular polygonal ferrite is mainly attributed to Ce2O2S, Ce2S3, CeAlO3, and VC, which can promote the nucleation of α‐Fe. Simultaneously, the addition of Ce reduces the phase transition temperature, increases the driving force of the phase transition, and increases the nucleation rate. This study's results can provide a reference for the application of Ce treatment in the preparation of nonquenched tempered steel for automobiles.

Heterogeneous nuclei of intergrowth eutectic in austenite-bainite steel modified by Ce and Al

TiC As Heterogeneous Nuclei of the (fe, Mn)3C and Austenite Intergrowth Eutectic in Austenite Steel Matrix Wear Resistant Composite

Study on Heterogeneous Nuclei in Cast H13 Steel Modified by Rare Earth

Eutectic Growth in As-Cast Medium Manganese Steel

Double Matching Heterogeneous Nucleation in Superhigh Manganese Steel

Achieving Enhanced Strength Retention at Elevated Temperatures in Ultrafine-Fibrous Interconnected Al-Ce-Ni Eutectic Alloy Solidified under Super-Gravity Field

Optimization of Inclusion and Microstructure of As‐Cast Nonquenched and Tempered Steel F38MnVS with Trace Ce

Stabilization of the Ternary Eutectic Growth in Additively Manufactured AlNiCe Alloys

Study on granulation mechanisms of γ+(Fe,Mn)3C eutectics in austenite steel composites

Elevated temperature microstructural stability in Al-7Cu-0.5Mn-0.2Zr alloys through Ce addition: Enhanced coherent interfacial stability of cu-rich θ'/α-Al interface

Effect of homogenization treatment on microstructure and eutectic precipitates in Ce‐containing 15Cr–22Ni–1Nb austenitic heat‐resistant stainless steel

Cerium Addition Effect on Modification of Inclusions, Primary Carbides and Microstructure Refinement of H13 Die Steel

Control of solidification structure of wear-resistant austenite-bainite polyphase steel with nodular eutectic

Microstructure diversity dominated by the interplay between primary intermetallics and eutectics for Al-Ce heat-resistant alloys

Study of the Formation and Intergrowth of Granular Eutectic in Austenitic Steel Matrix Composite by Directional Solidification Technology

Effect of Cerium Content on the Evolution of Inclusions and Formation of Acicular Ferrite in Ti-Mg-Killed EH36 Steel

Influence of cerium treatment on inclusion modification and as-cast microstructure of high-strength low-alloy steel

Evolutions of Microstructure by Cerium Treatment in As‐Cast M2 High‐Speed Steel

On the Al-Al11Ce3 Eutectic Transformation in Aluminum-Cerium Binary Alloys

Enhanced load transfer and ductility in Al–9Ce alloy through heterogeneous lamellar microstructure design by cold rolling and annealing

The Valence Electron Criterion on Heterogeneous Nucleus Catalysis During Non-Equilibrium Solidification of Austenite Steel