Abstract:A two-dimensional model for the simulation of solidification microstructure in multi-component alloy systems has been developed. The model is based on a cellular automaton (CA) technique for the calculation of the evolution of solid/liquid (S/L) interface. The dynamics of the interface is controlled by temperature, solute diffusion and Gibbs-Thomson effects. The diffusion equation for the temperature with release of latent heat on the S/L interface is valid in the entire domain, and the solute diffusion equation is also used in the entire domain through potential functions. Two methods are proposed to calculate the increment of the solid fraction. The first method is based on the level rule method similar to the one proposed by Jacot et al., but without the assumption of uniform temperature on the scale of the calculation domain. The second one is based on the calculation of the S/L interface velocity, which generalizes the results of Nastac and Beltran-Sanchez et al. for two-component alloy systems. If the concentration of one of the solutes tends to zero, both proposed methods reduce to the methods in Jacot et al. and Beltran-Sanchez et al. for two component alloy systems. Mesh independency is achieved by both methods and the dendritic morphologies obtained are the same if the mesh is fine enough. However, the morphologies of equiaxed dendrites calculated by using the interface velocity tends to the stable form more easily than those calculated using the level rule method as the mesh size is refined. For two-component alloy systems, the predictions of LGK theory for the steady-state tip velocity are compared with simulated values as a function of melt undercooling, which shows good agreement at very large range of undercooling. The simulated primary arm spacing in directional solidification is compared with experimental results for Fe-Si-Mg alloys and good agreement is also observed. It is noted that both methods for computing the solid fraction can be used for any multi-component alloy systems provided that the thermodynamic data are given

The Valence Electron Criterion on Heterogeneous Nucleus Catalysis During Non-Equilibrium Solidification of Austenite Steel

A new insight into heterogeneous nucleation mechanism of Al by non-stoichiometric TiCx

Rapid Solidification of Non-Stoichiometric Intermetallic Compounds: Modeling and Experimental Verification

Prediction of the Non-Isothermal Austenitization Kinetics of Fe-C-Cr Low Alloy Steels with Lamellar Pearlite Microstructure

Crystallographic Calculations and First-Principles Calculations of Heterogeneous Nucleation Potency of γ-Fe on La2O2S Particles

Electron Theory Study on Mechanism of Action of Cobalt in Fe-Co-Cr Based High-Alloy Steel

Valence Electron Structure Analysis of Refining Mechanism of Sc and Ti Additions on Aluminum

Effect of Ti/V Ratio on Thermodynamics and Kinetics of MC in Γ/α Matrices of Ti–V Microalloyed Steels

An improved cellular automata model for TiN inclusion precipitation

Transformation character of ferrite formation by a ledge mechanism under a mixed-control model

First-principles study on TiC/TiN heterogeneous nucleation interface in high-titanium steel

Density functional theory investigation on the stability, adhesion strength, tensile properties and fracture behavior of γ-Fe/Cu heterogeneous nucleation interface

Atomistic Nucleation Mechanism of Titanium Oxides in Steel Based on Homogeneous and Heterogeneous Modes

A general mixed-mode model for the austenite-to-ferrite transformation kinetics in Fe–C–M alloys

A Cellular Automaton Technique for the Modeling of Solidification Microstructure in Multi-Component Alloys

Heterogeneous nucleation of T1 precipitates in solid solution of Al-Cu-Li alloys from Ag-rich structures: An ab initio study

Study of the kinetics of austenite grain growth by dynamic Ti-rich and Nb-rich carbonitride dissolution in HSLA steel: In-situ observation and modeling

Effects Of Alloying Elements On The Kinetics Of Austenitization From Pearlite In Fe-C-M Alloys

Synergistic optimization in microstructure and mechanical properties of low carbon steel via trace amount of nano-sized TiC-TiB2

Ab initio study of energetics and structures of heterophase interfaces: From coherent to semicoherent interfaces

First principles study on heterogeneous interfaces of TiCu alloys through aluminum addition