Abstract:Eutectic microstructures are one of the most common solidification patterns in the binary or multi-component alloy systems. Due to the fine periodic microstructures of the eutectic alloys, the commercial applications of the eutectic alloys can improve the mechanical properties of the castings. The solidification mechanism of eutectic alloys has been widely studied by a lot of experimental works and theoretical analysis over the years. Recently, numerical models were used to study the mechanisms of formation of phase patterns and selection dynamics of the lamellar eutectic, such as phase field (PF) and cellular automaton (CA) model, which can promote the development of eutectic growth theory. Based on the existing CA method for binary primary a phase, a modified cellular automaton (MCA) model was developed for the simulation of binary eutectic growth. In this model, the influence of constitutional and curvature undercooling on the interface morphology was considered. The growth rate of eutectic interface was calculated by the solute conservation at the alpha/liquid and beta/liquid interfaces. The model could simulate the phenomenon of overgrowth, splitting and steady state growth of the eutectic lamellar. CBr4-C2Cl6 eutectic transparent alloy was chosen to validate the model. The simulated results showed that the increasing pulling rate lead to a smaller eutectic lamellar spacing, which had a good agreement with the Jackson-Hunt theory and the experimental results from the literature. Eutectic morphology evolution was simulated under a constant pulling rate and temperature gradient, which showed that the stable lamellar structures existed when the initial lamellar spacing was in a finite range between the minimum stable spacing lambda(m) and the limiting maximum stable spacing lambda(M). A smaller initial lamellar spacing would lead to lamellar annihilation. Conversely, a larger initial lamellar spacing could lead to the lamellar nucleation due to the appearance of solute rich concave at the center of the alpha/liquid interface. Meanwhile, the oscillatory instability of the eutectic lamellar was also reappeared by the MCA model. The MCA model was easily extended to 3D, and the lamellar rod transition during directional solidification was simulated, which showed that the ratio of volume fraction of alpha and beta phase was smaller than 1/pi tend to form lamellar rod transition when the initial lamellar spacing was smaller than lambda(m).

Stabilization of the Ternary Eutectic Growth in Additively Manufactured AlNiCe Alloys

Achieving Enhanced Strength Retention at Elevated Temperatures in Ultrafine-Fibrous Interconnected Al-Ce-Ni Eutectic Alloy Solidified under Super-Gravity Field

Phase-Field Simulation of the Microstructure Evolution in the Eutectic Alloy NiAl-31Cr-3Mo

Microstructure evolution and heterogeneous nucleation in ternary Al-Cu-Ni alloys

The formation mechanism of eutectic microstructures in NiAl-Cr composites

Strong cooperation growth of two phases in the ternary eutectic

Theoretical and numerical study of lamellar eutectic three-phase growth in ternary alloys

Ternary eutectic growth and associated tensile properties of directionally solidified Al87Si11Ni2 alloy

Effect of Mn on eutectic phase equilibria in Al-rich Al-Ce-Ni alloys

Nucleation and growth behavior of primary Al 11 Ce 3 intermetallic compounds during solidification in a hypereutectic Al-Ce alloy

Design Multicomponent Eutectic Alloys in the Co–Cr–Fe–Ni–Nb System Using Simple Mixing Method

Two-phase growth in peritectic Fe–Ni alloys

Influence of the phase fractions on the formation of eutectic colonies: A large‐scale phase‐field study

Coupled eutectic growth in Al-Fe alloys

In situ study of non-equilibrium solidification of CoCrFeNi high-entropy alloy and CrFeNi and CoCrNi ternary suballoys

From irregular to regular eutectic growth in the Al-Al3Ni system: in situ observations during directional solidification

On the Al-Al11Ce3 Eutectic Transformation in Aluminum-Cerium Binary Alloys

Microstructure evolution during directional solidification of off-eutectic Al-Cu-Mg alloys

Simulation of Eutectic Growth in Directional Solidification by Cellular Automaton Method

Application of finite element, phase-field, and CALPHAD-based methods to additive manufacturing of Ni-based superalloys

Utilizing integrated neutron diffraction and elastoplastic self-consistent crystal plasticity model to quantitatively assess the strengthening mechanism in Al-12.5Ce and Al-12.5Ce-0.4Mg alloys