Abstract:The main objective of this study is to predict the performance of an industrial‐scale (ID = 5.8 m) slurry bubble column reactor (SBCR) operating with iron‐based catalyst for Fischer–Tropsch (FT) synthesis, with emphasis on catalyst deactivation. To achieve this objective, a comprehensive reactor model, incorporating the hydrodynamic and mass‐transfer parameters (gas holdup, εG, Sauter‐mean diameter of gas bubbles, d32, and volumetric liquid‐side mass‐transfer coefficients, kLa), and FT as well as water gas shift reaction kinetics, was developed. The hydrodynamic and mass‐transfer parameters for He/N2 gaseous mixtures, as surrogates for H2/CO, were obtained in an actual molten FT reactor wax produced from the same reactor. The data were measured in a pilot‐scale (0.29 m) SBCR under different pressures (4–31 bar), temperatures (380–500 K), superficial gas velocities (0.1–0.3 m/s), and iron‐based catalyst concentrations (0–45 wt %). The data were modeled and predictive correlations were incorporated into the reactor model. The reactor model was then used to study the effects of catalyst concentration and reactor length‐to‐diameter ratio (L/D) on the water partial pressure, which is mainly responsible for iron catalyst deactivation, the H2 and CO conversions and the C5+ product yields. The modeling results of the industrial SBCR investigated in this study showed that (1) the water partial pressure should be maintained under 3 bars to minimize deactivation of the iron‐based catalyst used; (2) the catalyst concentration has much more impact on the gas holdup and reactor performance than the reactor height; and (3) the reactor should be operated in the kinetically controlled regime with an L/D of 4.48 and a catalyst concentration of 22 wt % to maximize C5+ products yield, while minimizing the iron catalyst deactivation. Under such conditions, the H2 and CO conversions were 49.4% and 69.3%, respectively, and the C5+ products yield was 435.6 ton/day. © 2015 American Institute of Chemical Engineers AIChE J, 61: 3838–3857, 2015

Oxidative Dehydrogenation of Butene to Butadiene in Gas-Solid-Solid Circulating Fluidization Reactor

Studies on Gas–solid–solid Circulating Fluidized-Bed Reactors

CFD simulation of cross flow in multi-tubular fixed-bed reactor of industrial level

Integrated bi-modal fluidized bed reactor for butane dehydrogenation to corresponding butylenes

Oxidative Dehydrogenation of 1-Butene to 1,3-Butadiene Using CO2 over Cr-SiO2 Catalysts Prepared by Sol-gel Method

The mass flow rate of powders in a gas-solid-solid circulating fluidization reactor

Control of Pressure Balance and Solids Circulation Characteristics in DCFB Reactors

Catalytic conversion of C4 fraction for the production of light olefins and aromatics

Assessing the Performance of an Industrial SBCR for Fischer–Tropsch Synthesis: Experimental and Modeling

CO2 oxidative dehydrogenation of n-butane to butadiene over CrOx supported on CeZr solid solution

Simulation Analysis of Gas-Solid Two-Phase Flow and Reaction in a Novel Catalytic Cracking Reactor

Hydrodynamic behaviors of gas-solid-solid circulating fluidized reactor

Oxidative dehydrogenation of n-butane on V/MgO catalysts. Influence of the type of contactor

Study of Propane Dehydrogenation to Propylene in an Integrated Fluidized Bed Reactor Using Pt-Sn/Al-SAPO-34 Novel Catalyst

Study on the FCC process of a novel riser-downer coupling reactor (III): Industrial trial and-CFD modeling

Reactive Adsorption Desulfurization Coupling Olefin Conversion in Fluid Catalytic Cracking Gasoline Upgrading Process

Discussion on the influence of internal components on the flow field distribution of a new gas–solid non-catalytic fluidized bed (NRFB)

Study of Fluid Catalytic Cracking Process in Experimental Downer Reactor

Transport Hydrodynamics of Particles in a Gas–solid Cyclone Reactor Using a Dense Discrete Phase Model and a Particle Size Segmentation Method

Aerobic Oxidation of Styrene in Functional Reactors and Computational Fluid Dynamics Simulation

Gas-Phase Catalytic Hydrochlorination of Acetylene in A Two-Stage Fluidized-Bed Reactor