Abstract:Squeeze casting process can effectively resolve the casting difficulties for wrought aluminum alloys by pressurized solidification. The effects of applied pressure (0.1-125 MPa) on the microstructure refinement, non-equilibrium eutectic phase aggregation and fracture behavior of Al-Zn-Mg-Cu alloys prepared by squeeze casting were investigated through metallography, scanning electron microscopy and energy dispersive spectroscopy. The results showed that the primary α-Al grains transformed from coarse dendrites to refined equiaxed grains with increasing pressure. Considerable primary refinement was achieved at 100 MPa, with a significant decrease by 63% in the average grain size from 273 μm to 101 μm; the non-equilibrium eutectic phases were homogenized and refined, and almost dissolved into the Al matrix after T6 heat treatment. The mechanism of solidification behaviors in pressurized solidification was elucidated. Firstly, the applied pressure increased the thermodynamic driving force to promote primary grain nucleation. Secondly, the solute diffusion and constitutional undercooling at the front of the solid/liquid interface front were inhibited by pressure, and grain growth in a dendritic structure was thus restrained. Thirdly, interdependence theory and thermodynamic calculations were conducted to quantitatively describe the primary grain size changes under pressurized solidification. Lastly, the ternary eutectic reaction L → α-Al + T-Mg (Al, Zn, Cu) 2 + Al 2 Cu and binary eutectic reaction L→ α-Al + Al 7 Cu 2 Fe were suppressed by the reduced solute segregation. Furthermore, when the pressure increased from 0.1 MPa to 125 MPa, the ultimate tensile strength was raised from 428 MPa to 538 MPa, almost approaching that of samples by forging process. The refined eutectic phases decreased stress concentration and improved fracture behaviors.

Research on solidifying characteristics of zinc alloy by liquid metal forging process

On the Size Effects in Micro/meso Semisolid Extrusion–forging of A356 Aluminum Alloy

Mechanics and Forming Theory of Liquid Metal Forging

Research Progress of Metals and Alloys Pressurized Solidification

Effect of Zn/Mg/Cu Additions on Hot Cracking Tendency and Performances of Al-Cu-Mg-Zn Alloys for Liquid Forging

Development of a Semi-solid Zn-Al Alloy Filler Metal with Globular Grains

An innovative thermal simulation study of microstructure improvement by delay forging during solidification

Effect of pressure on the microstructure refinement, solidification mechanism and fracture behavior of wrought Al-Zn-Mg-Cu alloys prepared by squeeze casting

Effect of Forging on Microstructure and Properties of Al-9Si-5Cu-0.2Zr-0.1Sr-0.16Ti-0.1Ce Cast Aluminum Alloy

Experimental research on fluidity of semi-solid alloy ZL101 mircoextrusion

Effect of Cooling Rate on Solidification Structure of Zinc-Aluminum-Magnesium Alloy

An Investigation into Aluminum–aluminum Bimetal Fabrication by Squeeze Casting

Relationship of Compositions, Phase Constituents and Solidification Paths of Casting Mg-Al-Zn Alloys

Effects of different holding pressures on the microstructure and mechanical properties of Al-5.9Zn-2.2Mg-1.8Cu alloy

Experiment and Numerical Simulation of Microstructure of ZL114A Alloy in Low Pressure Casting

Microstructure Simulation of Zl114a Alloy During Low Pressure Die Casting Process

Experimental and numerical studies on the influence of centrifugal casting parameters on the solidification structure of Al-Cu alloy

Research on Structure Property of AZ91D Magnesium Alloy Produced by Liquid Combination Process of Die Casting and Forging

Casting with Zinc Alloys

Solidification behavior and enhanced properties of semi-solid Al–8Si–0.5Fe alloys fabricated by rheo-diecasting

Effects of Thermal Variables of Solidification on the Microstructure and Hardness of the Manganese Bronze Alloy Cu-24Zn-6Al-4Mn-3Fe