Abstract:The effect of cold-drawing on the tensile property and giant magneto-impedance (GMI) effect of melt-extracted Co-based amorphous microwires was evaluated through detailed analyses of the distribution of residual stress and microstructural evolution. The tensile ductility and tensile strength increased gradually with cross-sectional area reduction ratio (R) until 51%, and decreased with further deformation. The microwire with R=51% exhibits the highest tensile ductility of 1.09% and tensile strength of 4320MPa. Structural and thermodynamic analyses reveal that it is the mechanical deformation rather than thermal activation that induces the precipitation of nanocrystals and arrests the quick extension of shear bands leading to the enhanced ductility. Interestingly, the GMI effect also attains the maximum value of 160% at 10MHz when R=51% (30% larger than that of the as-cast wires), before decreasing with further cold-drawing. Such an identical evolution trend of both tensile and GMI properties can be ascribed to two underlying mechanisms: the generation of longitudinal and circumferential residual stresses and the growth of deformation-induced nanocrystals during cold-drawing. The role of residual stress is established herein not only as a trigger to accelerate the amorphous-to-nanocrystalline phase transformation but also as a decisive contributor to the mechanical and GMI performance. The unique simultaneous improvement of both mechanical and GMI properties of cold-drawn Co-based microwires opens up new possibilities for a variety of engineering applications, such as high-performance magnetic, stress and biological sensors.

Microstructural evolution and its relationship to GMR in melt-spun Cu70Co30

MICROSTRUCTURE OF AS-MELT SPUN Al-Cu-Mg-Fe-Ni ALLOY AND ITS VARIATION IN CONTINUOUS HEAT TREATMENT

Compositions, Magnetic Properties and GMR Performances of Melt-Spun Cu–Co–Ni Ribbons

Relating Residual Stress and Microstructure to Mechanical and Giant Magneto-Impedance Properties in Cold-Drawn Co-based Amorphous Microwires

Tuning of magnetocaloric effect and optimization of scaling factor for Gd 55 Ni 10 Co 35 amorphous microwires

Microstructural Evolution of a Newly Developed γ' Strengthened Co-base Superalloy

Improving Mechanical and Magnetocaloric Responses of Amorphous Melt-Extracted Gd-based Microwires Via Nanocrystallization

Microstructure and Martensitic Transformation Behavior of the Ni50mn36in14 Melt-Spun Ribbons

Microstructures of Melt-Spun Cu100−x–Crx (x=3.4–25) Ribbons

Microstructures and Mechanical Properties of a L12-structured Precipitation Strengthened Co-based Superalloy

Correlation of Magnetic Domains, Microstructure and Gmi Effect of Joule-Annealed Melt-Extracted Co68.15fe4.35si12.25b13.75nb1cu0.5 Microwires for Double Functional Sensors

Microstructure, martensitic transformation kinetics, and magnetic properties of (Ni50Mn40In10)100−xCox melt-spun ribbons

Effects of Melt-Spinning on Refining of Microstructures for CuCr25 Alloy and Their Chopping Currents

Magnetoresistance and Microstructure Evolution Upon Rapid Thermal Annealing of Giant Magnetoresistive Co/Cu/Co/CoNbZr Multilayers

Microstructure Evolution and Mechanical Stability of Supersaturated Solid Solution Co-Rich Nanocrystalline Co-Cu Produced by Pulsed Electrodeposition

Effect of titanium additives on the microstructure of melt-spun CuCr ribbons

Suppression of Γ Phase in Ni38Co12Mn41Sn9 Alloy by Melt Spinning and Its Effect on Martensitic Transformation and Magnetic Properties

Effects of Rare Earth Additions on GMR of Melt-Spun Cu–Co–Ni Ribbons

Giant Magnetoresistance and Microstructure of Co-Cu and Feco-Cu Granular Films

Microstructure and magnetic properties of nanocrystalline Co-doped Sendust alloys prepared by melt spinning

Microstructure, Magnetic Properties and Giant Magnetoresistance of Granular Cu-Co Alloy