Abstract:Highlights • Resin-composite restorations modeled using dentin-composite discs. • Oral cavity conditions mimicked using accelerated fatigue and chemical preconditioning. • SEM analysis showed adhesive/hybrid layer prominent on fracture surfaces. • Cyclic fatigue had greater impact than preconditioning on degradation at interface. • Findings correlated with long-term clinical resin-dentin bond degradation studies. Objective The current study aimed to evaluate the effects of different combinations of chemical and mechanical challenges on the failure load, failure mode and composition of the resulting fracture surfaces of resin-composite restorations. Methods Three resin composites were used to fill dentin disks (2 mm inner diameter, 5 mm outer diameter, and 2 mm thick) made from bovine incisor roots. The model restorations, half of which were preconditioned with a low-pH buffer (48 h under pH 4.5), were subjected to diametral compression with either a monotonically increasing load (fast fracture) or a cyclic load with a continuously increasing amplitude (accelerated fatigue). The load or number of cycles to failure was noted. SEM was performed on the fracture surfaces to determine the proportions of dentin, adhesive, and resin composite. Results Both cyclic fatigue and acid preconditioning significantly reduced the failure load and increased the proportion of interfacial failure in almost all the cases, with cyclic fatigue having a more pronounced effect. Cyclic fatigue also increased the amount of adhesive/hybrid layer present on the fracture surfaces, but the effect of acid preconditioning on the composition of the fracture surfaces varied among the resin composites. Significance The adhesive or hybrid layer was found to be the least resistant against the chemomechanical challenges among the components forming the model restoration. Increasing such resistance of the tooth-restoration interface, or its ability to combat the bacterial actions that lead to secondary caries following interfacial debonding, can enhance the longevity of resin-composite restorations.

Investigation of durability of composite resin (2) effect of tension fatigue on wear resistance of composite resin

Research on the Aging Effects of Adhesive and Composites on the Degradation Mechanism of Composite Adhesive Joints in Thermal-Humidity-Cycles for Automobiles

Determination of the tensile residual properties of a wound carbon/epoxy composite first exposed to fire

Effects of rotating fatigue on the mechanical properties of microhybrid and nanofiller-containing composites.

Wear of resin composites: Current insights into underlying mechanisms, evaluation methods and influential factors

Investigation of stress and tribological properties of dental composite materials using FEM

Fatigue of the resin-dentin interface: a new approach for evaluating the durability of dentin bonds

An In Vitro Investigation Of Wear Resistance And Hardness Of Composite Resins

A Study of the Residual Stress and Its Influence on Tensile Behaviors of Fiber-Reinforced Sic/Al Composite

The Effects of Load and Frequency on the Fatigue Damage of Bi-Layered Zirconia and Alumina Dental Composites

Post-failure analysis of model resin-composite restorations subjected to different chemomechanical challenges

Experimental Investigation on Strain Rate Effect of High-Performance Fiber Reinforced Cementitious Composites Subject to Dynamic Direct Tensile Loading

Fatigue Failure Behavior of Aramid Fiber Reinforced Styrene Butadiene Rubber Composite with Different Fiber Coatings

Tension-tension fatigue properties of multiaxial laminated carbon/epoxy composites molded by high-pressure resin transfer molding (HP-RTM) process

Effect of Resin-Missing Defects on Tensile Behavior of Carbon Fiber/Epoxy Composites

Wear rates of regular and tempered composites

Analysis on effect of injection residual stress on impact resistance of composite wheel made of long glass fiber reinforced thermoplastic

Effects of three stress levels on the fatigue properties and fracture mechanisms of an in-situ synthesized TiB/Ti-6Al-4V titanium matrix composite

Understanding friction and wear properties of carbon fiber/epoxy stitched composites

Experimental study on tension and compression mechanical property of 3D fine woven punctured C/C composites

Friction and wear of dental CAD/CAM composite resin