Abstract:The effect of cold rolling and annealing on texture development and mechanical behavior of Zircaloy-4 alloy plates was systematically investigated in the present work. The as-received plates were subjected to cold rolling with thickness reductions of 33% and 66%. Electron back-scatter diffraction and tensile tests were performed to reveal the texture and mechanical properties, respectively. Results showed that a bimodal texture was featured in the as-received plate and the texture was a fiber that spread from <<math>101¯0</math>> to <<math>112¯0</math>>. After cold rolling and annealing, a fiber with a continuous distribution from <<math>101¯0</math>> to <<math>112¯0</math>> and a fiber with a maximum at the <<math>112¯0</math>> position were present in the plates with thickness reductions of 33% and 66%. Besides, the existence of {<math>0001</math>} basal fiber was noticed, indicating more basal poles oriented toward the normal direction. Tensile tests showed that the recrystallized plate with 66% thickness reduction was more ductile and less strong than that with 33% reduction. Meanwhile, tensile properties were sensitive to strain rate, loading direction and thickness reduction. Moreover, the relationship between texture development and yield strength was discussed based on Schmid theory. Calculated results indicated that prismatic <a> slip was the predominant deformation mode and its Schmid factor values under different loading directions contributed to the anisotropy of yield strength. Due to the texture development during cold rolling and annealing, the averaged SF values for prismatic <a> slip changed with the increased thickness reduction, resulting in the variation of yield strength.</a></a>

Study of cold deformation and low temperature annealing textures in Zr-Nb alloy sheet

Texture Evolution and Temperature-Dependent Deformation Modes in Ambient- and Cryogenic-Rolled Nanolayered Zr-2.5Nb

EFFECT OF ANNEALING TEMPERATURE ON TEXTURE OF COLD-ROLLED NI47TI44NB9 SHEET

New insight of texture and microstructure evolution, and the connections between with tensile performance in as-annealed Al-Cu-Mg-Zr sheet

Texture development and mechanical behavior of Zircaloy-4 alloy plates fabricated by cold rolling and annealing

Effect of annealing treatment on texture evolution, microstructure and mechanical properties of an extruded Mg-Gd-Zn-Zr alloy

Effect of Annealing on the Microstructure, Texture and Tensile Deformation Properties of Cu–3 Wt%ag–0.5 Wt%zr Thin Sheets Rolled at Room and Cryogenic Temperature

Insights into the evolution of texture and mechanical properties during warm rolling and annealing of Mg–2Zn-0.5Ca alloy

Influence of Heat Treatment on the Texture, Microstructure and Tensile Deformation Behaviours of Cold Rolled FeCoNiCr Sheets

Deformation mechanism, orientation evolution and mechanical properties of annealed cross-rolled Mg-Zn-Zr-Y-Gd sheet during tension

Investigation on deformation mechanisms of Zr-1Sn-0.3Nb-0.3Fe-0.1Cr alloy using in situ EBSD/SEM

Effect of Low-Temperature Pre-Deformation on Precipitation Behavior and Microstructure of A Zr-Sn-Nb-Fe-Cu-O Alloy During Fabrication

Concurrent Inheritance of Microstructure and Texture after Slow Β→α Cooling of Commercially Pure Zr

Effect of cryogenic rolling on the microstructure and texture of CuCrZr alloy

Texture Evolution, Microstructure, and Superelastic Properties of Different Cold-Rolled Ti-Zr-Nb-Sn Strain Glass Alloys

On the Strength-Hardness Relationships in a Zr-Nb Alloy Plate with Bimodal Basal Texture Microstructure

Regularities of Changes in the Structure of Different Phases of Deformed Zirconium Alloys as a Result of Raising the Annealing Temperature According to Texture Analysis Data

Evolution of texture and intergranular stresses of αZr and minority phases in Zr-2.5Nb pressure tube through synchrotron X-ray diffraction

Quasi-in-situ Observations of Low-Angle Grain Boundaries, Twins and Texture Evolution During Continuous Annealing in a Cold-Rolled Mg-Zn-Gd Alloy

The Preferential Growth and Related Textural Evolution During Static Recrystallization in a Cold-Rolled Mg–Zn–Gd Alloy

Coupling Thermomechanical Processing and Alloy Design to Improve Textures in Mg-Zn-Ca Sheet Alloys