Abstract:In this study, structural, morphological, thermal and magnetic properties of amorphous-nanocrystalline Fe 70 Cr 10 Nb 10 B 10 (at.%) alloy are discussed. The formation and evaluation of amorphous-nanocrystalline structures of the alloy were followed by XRD, SEM-EDX, TEM, DTA, and VSM techniques. After 50 h of milling Cr, Nb, and B were completely dissolved into the Fe lattice forming 82% of the amorphous phase of the alloy. A gradual dissolution of the alloying elements also increased the lattice parameters concurrently. The lattice parameters reached a maximum value of 2.908 Å after 20 h of milling and then leveled off to a value of 2.891 Å at the end of 50 h of milling. Based on the XRD data, crystallite size and lattice strain of the alloy were calculated as 3.2 nm and 3.34% respectively. TEM analyses revealed that the alloy particulates comprised needle-shaped nanoparticles of an average size of 21 nm. The room temperature magnetic hysteresis loops showed that the increased duration of milling decreased the saturation magnetization from 91 to 24 emu/g. This was mainly due to the upsurge on the amorphous phase content in the alloy as the milling progressed. The increase in amorphous phase content and the subsequent reduction of the saturation magnetization were due to the inter-diffusion of the non-ferromagnetic Cr and B atoms into the Fe lattice. Thermal studies revealed that around 350 °C the amorphous phase of the alloy began crystallizing. The magnetic saturation of the heat-treated alloy also increased with the growth in the crystalline phases. The 50 h milled sample annealed at 700 °C was found to have the highest magnetic anisotropy as observed from the temperature-dependent zero-field cooled and field cooled magnetization measurements. The high-pressure X-ray diffraction measurements revealed that the amorphous state of the alloy remained stable up to 11.3 MPa. It also revealed the structural similarities of the Fe 70 Cr 10 Nb 10 B 10 alloy with those of the Fe 70 M 10 B 20 (M = Nb and Cr) types. For all practical purposes, the microstructural stability under high compressive pressure represents the consolidation properties of the nanostructured magnetic materials since both pressure and temperature-induced phase transformations are the primary controlling factors for the specific magnetization properties of the alloy.

Formation of amorphous Fe50Ti50 prepared by mechanical alloying and the influence of milling intensity

Investigation of a Hot-Pressed Nb–Ti–Al Alloy: Mechanical Alloying, Microstructure and Mechanical Property

Formation of Nanocrystalline Fcc Phase by Mechanically Driven Crystallization

Amorphization in the AlC System by Mechanical Alloying

Synthesis of High-Thermally Stable Ni60Nb13.3Zr13.3Ti13.3 Amorphous Alloy by Mechanical Alloying

X-ray absorption fine structure and x-ray diffraction studies on structures of Fe70Cu30 alloys affected by mechanical alloying

Microstructural and Magnetic Characteristics of High-Entropy FeCoNiMnTi Alloy Produced via Mechanical Alloying

PHASE TRANSFORMATION IN ANNEALED MECHANICAL ALLOYING Nd-11Fe-Ti ALLOY AND ANNEALED MECHANICAL MILLING NdFe11Ti COMPOUND

Structural and thermal properties of the Fe-based alloys prepared by mechanical milling

Preparation of amorphous Fe-Zr alloys by mechanical alloying and melt spinning methods

Formation of Nanocrystalline Solid Solution in Al-Fe-V-Si Alloys by Mechanical Alloying

Phase Transformation and Morphology Evolution of Ti50Cu25Ni20Sn5 during Mechanical Milling

The Crystallization Kinetics Study of Finemet-Co Amorphous Alloys

Microstructures of Mechanically Alloyed Fe60Ni40 Studied by XAFS and XRD

Mechanical Alloying Effect on the Structure of Fe-Al-(Si) Alloy

Nanocrystalline/Amorphous Tuning of Al–Fe–Nb (Mn) Alloy Powders Produced via High-Energy Ball Milling

Formation of AlCuFe icosahedral quasicrystal by mechanical alloying: XAFS and XRD studies

Effects of milling process parameters and PCAs on the synthesis of Al0.8Co0.5Cr1.5CuFeNi high entropy alloy powder by mechanical alloying

Synthesis Mechanism of Amorphous Si2BC3N Powders: Structural Evolution of 2si‐bn‐3c Mixtures During Mechanical Alloying

Nonequilibrium phase transformation of NdFe11Ti compound during mechanical milling

Synthesis and characterization of amorphous-nanocrystalline Fe70Cr10Nb10B10 powders by mechanical alloying