Abstract:Amorphous 2Mg–Fe+xwt.% Ni alloys were synthesized by mechanical alloying of Mg and Fe elemental powders. Two kinds of ball-milling atmospheres, namely, (1) under argon and (2) first under argon and then in tetrahydrofuran (THF), were examined in this study. The effects of the Ni addition and ball-milling time and atmosphere on the microstructure and electrochemical properties of the prepared alloys have been investigated systematically. The results show that the ball-milled (2Mg–Fe) nickel-free mixture still maintains Mg and Fe elemental phases, and its discharge capacity is only 19.2mAhg−1. The Ni powder addition is advantageous for the formation of Mg–Fe amorphous structure and for the improvement of the electrochemical properties of the alloys. For the alloys milled under argon, with the Ni content x increasing, the discharge capacity of the alloys increases first and then decreases, and reaches a maximum value of 455.3mAhg−1 as x=100. With the milling-time extending, the discharge capacity of the alloy increases first and then decreases too. For the alloys milled under argon and then in THF, the alloys exhibit higher degree of amorphorization, bigger specific surface area and more active surfaces, and thus have better electrochemical properties than those milled under argon. With the Ni increasing, the discharge capacity increases from 249.7mAhg−1 (x=50) to 565.2mAhg−1 (x=150) and then decreases to 497.9mAhg−1 (x=200), and the exchange current density I0 increases from 104.8mAg−1 (x=50) to 251.1mAg−1 (x=200), which is consistent with the variation of the HRD of the alloy electrodes in the investigation range.

Microstructures of Mechanically Alloyed Fe60Ni40 Studied by XAFS and XRD

MICROSTRUCTURE OF AS-MELT SPUN Al-Cu-Mg-Fe-Ni ALLOY AND ITS VARIATION IN CONTINUOUS HEAT TREATMENT

X-ray absorption fine structure and x-ray diffraction studies on structures of Fe70Cu30 alloys affected by mechanical alloying

Mechanical Alloying, Fine Structure and Thermal Decomposition of Nanocrystalline Fcc-Fe60cu40

Local Structures Of Mechanically Alloyed Al70cu20fe10 Nanocomposites Studied By Xrd And Xafs

Local Structures of Mechanical Alloying Fe70Cu30 System Studied by XAFS

XAFS Study on Fe60Si40 Alloy Processed by Mechanical Alloying

Microstructures of Fe 77- X Ni X Cu 1 Nb 2 P 14 B 6 Soft Magnetic Alloys Studied by X-Ray Absorption Fine Structure

Microstructures and Mechanical Behaviors of NiAlFe Intermetallic Compounds

Microstructural and Magnetic Characteristics of High-Entropy FeCoNiMnTi Alloy Produced via Mechanical Alloying

Structural and thermal properties of the Fe-based alloys prepared by mechanical milling

Structural Studies of Nanometeric Fe100-xCux Alloys

High throughput in-situ synthesis of Fe-Cr-Ni alloys via laser powder bed fusion: exploring the microstructure and property evolution

Preparation and properties of FeNiMnCuC0.2Alx high-entropy alloy

Local Structure Evolution of FexNi77-xCu(1-)Nb2P14B6 Soft Magnetic Materials by Mechanical Alloying.

Electrochemical properties of amorphous Mg–Fe alloys mixed with Ni prepared by ball-milling

Transmission Electron Microscopy Studies of Mechanical Alloying in the Immiscible Fe2o3-Sno2 System

Magnetic properties and Structural characterization of nanocrystalline Fe-20%A (Ni, Co and Si) alloys powders synthesized by mechanical alloying process

Metastable Structures of Immiscible System Induced by Mechanical Alloying

Mechanical Alloying Effect on the Structure of Fe-Al-(Si) Alloy

Microstructure and Magnetic Properties of Nanocrystalline Fe60−xCo25Ni15Six Alloy Elaborated by High-Energy Mechanical Milling