Abstract:To reduce the decarburization of WC, the core-shell WC-16Cr3C2-10Co4Ni-La2O3 (named as WC-Cr3C2-CoNiLa in following) powder was prepared through second agglomeration and spray granulation process and deposited using high velocity oxygen fuel (HVOF) spraying. Microstructure and phase constitutions of the deposited coating were characterized using scanning electronic microscopy (SEM) with energy dispersive spectrometer (EDS) and X-ray diffraction (XRD), respectively. Microhardness, elastic modulus, and fracture toughness of the coating were tested by indentation method. Wear properties of the coating under different applied loads were evaluated by two body dry sliding wear using a pin-on-disc tester. Experimental results showed that the HVOF sprayed WC-Cr3C2-CoNiLa coating was mainly consisted of WC, Cr3C2, Co, Ni phases and a little of Cr2O3 without any WC decarburized phases including W2C, M6C and M12C). Most of WC carbide in the coating presented a round outline with the average particle size of 0.54 ± 0.35 μm and average crystal sizes 401 ± 91.41 Å in different crystal orientation index. The coating presented dense microstructure with the porosity about 1.16 ± 0.39%, and some lamella features with well bonded interfaces of carbide particles/binder phase, inter-splats and coating/substrate. Microhardness, elastic modulus, fracture toughness and wear rate of the coatings were 12.57 ± 0.52 Hv0.3, 153.91 ± 31.66 GPa, 5.31 ± 0.51 MPa⋅m1/2 and 6.67*10−3-11.11*10−3 mg/(Nm) when the applied load increased form 5 N to 15 N, respectively. The abrasive wear of the coating occurred mainly in the form of gouging and plastic deformation as well as peeling off carbide particles.

Studies of Laser Hybrid Plasma Spraying WC–10Co4Cr Coatings

Microstructures and performances of the WC-10Co4Cr coatings deposited by laser hybrid plasma spraying technology

Microstructure and Deposition Mechanism of Laser-Hybrid Plasma Spraying NiCr-Cr3C2 Coating

Influence of Laser Power on the Microstructure and Anti-Wear Performance of Laser Hybrid Plasma Spraying NiCr-Cr3C2 Coatings

Microstructure and Tribological Properties of Laser-Remelted Ni-Based WC Coatings Obtained by Plasma Spraying

Effect of Cobalt and Chromium Content on Microstructure and Properties of WC-Co-Cr Coatings Prepared by High-Velocity Oxy-Fuel Spraying

Study on Properties of Coatings Prepared by Supersonic Plasma Spraying with Three Kinds of WC-12Co Powder

Wear performance of the plasma sprayed fine WC-Co composite powders coatings

Corrosion characteristics of plasma-sprayed Ni-coated WC coatings comparison with different post-treatment

Influence of process parameters on appearance of plasma-melt-sprayed WC-17%Co coatings

Microstructure and tribological characteristics of ZrO2–Y2O3 ceramic coatings deposited by laser-assisted plasma hybrid spraying

Characterization on microstructures and properties of WC-CoCr coating deposited by HVAF and HVOF processes

A Comparative Study on Wear and Corrosion Behaviour of HVOF- and HVAF-sprayed WC–10Co–4Cr Coatings

Microstructure, phase constitution and mechanical properties of WC-Cr3C2-CoNiLa coatings fabricated by using HVOF spraying core-shell powder

Microstructure Characterization and Abrasive Wear Performance of Hvof Sprayed Wc-Co Coatings

Performance evaluation of HVOF sprayed WC-10Co4Cr coatings under slurry erosion

Influence of Laser Power on the Microstructure and Anti-Corrosion Performance of LHPS NiCrAlY Coatings

Microstructure, interface characteristics and tribological properties of laser cladded NiCrBSi-WC coatings on PH 13-8 Mo steel

Comparative tribological study of air plasma sprayed WC–12%Co coating versus conventional hard chromium electrodeposit

Research on microstructure, mechanical property and wear mechanism of AlCoCrFeNi/WC composite coating fabricated by HVOF

Analysis of Microstructure of WC-12Co Coatings Prepared by the Three Kinds of Supersonic Thermal Spraying Processes