Abstract:Ni-based WC coatings were successfully fabricated on Ti6Al4V titanium alloy substrate by the air plasma spraying (APS) process. The as-sprayed coatings were remelted with a continuous wave CO2 laser. The coatings were characterized using a scanning electron microscope (SEM), an energy dispersive spectrometer (EDS), an X-ray diffractometer (XRD), a Vickers microhardness tester, a ball-on-disc friction and wear tester, and a 3D measuring laser microscope. The results indicated that the laser-remelted coatings possessed a more homogeneous microstructure and lower porosity, were more dense, and bonded well with the substrate. The lamellar structure and microcracks of the as-sprayed coatings were eliminated after laser remelting. The average porosity markedly decreased to 1.3% from 9.7% of the as-sprayed coating. Many needle dendrites grew outward from the dissolution surface of the WC, while massive precipitates abundantly appeared around and away from the WC particles. The microhardness of the laser-remelted coating was enhanced to 884.7–1363.3 HV0.3, which was much higher than that of the as-sprayed coatings and nearly three times higher than that of the substrate. Under the same load, the wear volume of the substrate was nearly 13 times higher than that of the laser-remelted coating and five times higher than that of the as-sprayed coating. The wear mechanism of the laser-remelted coating and the as-sprayed coating was mainly abrasive wear; however, the wear mechanisms of the substrate were a combination of adhesive wear, micro-cutting, and delamination wear.

Influence of Laser Power on the Microstructure and Anti-Wear Performance of Laser Hybrid Plasma Spraying NiCr-Cr3C2 Coatings

Influence of Laser Power on the Microstructure and Anti-Corrosion Performance of LHPS NiCrAlY Coatings

Microstructure and Deposition Mechanism of Laser-Hybrid Plasma Spraying NiCr-Cr3C2 Coating

Studies of Laser Hybrid Plasma Spraying WC–10Co4Cr Coatings

Microstructures and performances of the WC-10Co4Cr coatings deposited by laser hybrid plasma spraying technology

Microstructure and Wear Resistance of Laser Cladded Ni-based Coatings with Nanometer La2O3 Addition

Microstructure and Wear Resistance of Laser Cladding NiCrWB Alloy Coating on Cu Substrate

Microstructure and Tribological Properties of Laser-Remelted Ni-Based WC Coatings Obtained by Plasma Spraying

Microstructure and Properties of Laser-assisted Thermal Spraying NiCoCrAlYTa/ZrO2/BaF2 center dot CaF2 Coating

High-Temperature Dry Sliding Friction and Wear Behavior of Ni60a Coating on the 20crnimo Alloy Surface Treated by Laser Shock Peening and Its Bonding Zone

Laser Damage Resistant Properties of Plasma Sprayed Ni-Coated Coatings Irradiated by High-Power Continuous Laser

Laser Remelting of Plasma Sprayed Nanostructured Al2O3–TiO2 Coatings at Different Laser Power

Microstructure and Corrosion Properties of Plasma-Sprayed NiCr–Cr3C2 Coatings Comparison with Different Post Treatment

Micro structure and hardness of Ni-/NiCr-Cr3C2 coating by laser cladding

Microstructure and Tribological Properties of Plasma Sprayed Al–Cu–Fe Quasicrystalline Coatings after Laser Post-Treatment Processing

The microstructure and tribological characteristics of laser-clad Ni–Cr–Al coatings on aluminium alloy

Process Optimization of laser remelting plasma -sprayed NiCr-Cr3 C2 coatings

Effect of laser lower and remelting on the microstructure and tribological properties of GH3230 superalloy coating fabricated by laser melting deposition

Microstructure and Wear Resistance of Laser Cladding NiCrMn-WC Composite Coatings

The Microstructure, Surface Topography and Wear Resistance of Cold-Sprayed (Cr3C2-25(Ni20Cr))-(Ni-graphite) Composite Coatings Modified by Diode Laser Treatment

Microstructure and Tribological Properties of FeCrBSi Amorphous Alloy Coatings by Ultra-High-Speed Laser Cladding