Abstract:The influence of processing and microstructure on the mechanical properties of Sialon-based ceramics, in-situ self-toughening induced by heat treatment and second-phase toughened, was investigated. Three kinds of Sialon-based ceramic materials were covered in the research: 1. TiB(p), MoSi2(p), SiC(p), and SiC(w) second-phase reinforced Sialon materials; 2. alpha/beta-double-phase-Sialon ceramics, using rare earth oxides Nd2O3, Dy2O3, and Yb2O3 as sintering additives, 3. Sialon ceramics with elongated alpha-sialon grains. The experimental resules showed that as to TiB(p), MoSi2(p), SiC(p), and SiC(w) second-phase reinforced Sialon materials, the toughening effect is mainly controlled by the bonding between matrix and second-phase and the critical size of second-phase particles. In Nd2O3-, Dy2O3-, and Yb2O3-added Sialon ceramics, Nd2O3 is a kind of effective sintering additive and Nd-Sialon possesses the highest K-1c, value (7.0 MPa.m(1/2)) due to the elongated beta-Sialon grains developed by heat treatment in order to induce in-situ self-toughening mechanism. Yb2O3 is not only an effective sintering additive, but also a useful alpha-Sialon stabilizer, so Yb-Sialon is hard, with a highest Vickers hardness H-v10 of 18.0 GPa, because of the existing of equiaxed alpha-Sialon grains in the samples. The action of Dy2O3 is between Nd2O3 and Yb2O3. The growth mechanism of elongated alpha-sialon grains is declared to be the heterogeneous nucleation and anisotropic growth.

Development of Elongated 6H-Sic Grains in Reaction-Bonded Porous SiC Ceramics

Effect of Removal of Silicon on Preparation of Porous SiC Ceramics Following Reaction Bonding and Recrystallization

Fabrication, Structure and Properties of Porous SiC Ceramics with High Porosity and High Strength

Preparation of C-Axis Textured SiC Ceramics by a Strong Magnetic Field of 6 T Assisted Gel-Casting Process

Fabrication and Properties of SiC Porous Ceramics by Slip Casting Process

Porous 2h‐silicon Carbide Ceramics Fabricated by Carbothermal Reaction Between Silicon Nitride and Carbon

Effects Of Grain Grading On Microstructures And Mechanical Behaviors Of Pressureless Solid-State-Sintered Sic

Microstructure and Mechanical Properties of Porous SiC Ceramics by Carbothermal Reduction and Subsequent Recrystallization Sintering

Grain Growth and Recrystallization Behaviors of an Ultrafine Grained Al-0.6 Wt%mg-0.4 Wt%si-5Vol.%sic Nanocomposite During Heat Treatment and Extrusion

Processing, Microstructures and Mechanical Properties of Aqueous Gelcasted and Solid-State-Sintered Porous Sic Ceramics

Fabrication and Properties of Cordierite–mullite Bonded Porous SiC Ceramics

Fabrication of Gradient Porous SiC Ceramics with Directional Pores Without Templates

Densification and Enhancement of Sic Particulate Reinforced Fine Grain Sic Ceramic

Influence of Processing and Microstructure on Mechanical Properties in Sialon-Based Ceramics

In Situ Growth of Elongated Al2O3 Grains Induced by Al Nanoparticles

Simultaneous improvement in porosity and strength of porous β-Si3N4 ceramics by formation of ultrafine fibrous grains

Fabrication and Properties of Reaction-Formed SiC by Infiltrating Molten Si into Mesocarbon Microbeads-Based Carbon Preform

Fabrication and Characterization of Hierarchical Porous SiC Ceramics Via Gelcasting and Carbothermal Reduction Between Carbon and SiO

Preparation of <i>In Situ</i> Synthesized SiC Particles Reinforced Highly Porous Si<sub>3</sub>N<sub>4</sub> Ceramics by Gel-Casting

Preparation and Characterization of Pure SiC Ceramics by HTPVT Induced by Seeding with SiC Nanoarrays

A new approach for the net-shape fabrication of porous Si3N4 bonded SiC ceramics with high strength