Abstract:Solar cells based on kesterite-type $Cu_2ZnSnS_4$ (CZTS) thin films were fabricated using a chemical route to prepare the $CZTS$ films, consisting in sequential deposition of $Cu_2SnS_3$ (CTS) and $ZnS$ thin films followed by annealing at $550^\circ C$ in nitrogen atmosphere. The $CTS$ compound was prepared in a one-step process using a novel chemical procedure consisting of simultaneous precipitation of $Cu_2S$ and $SnS_2$ performed by diffusion membranes assisted $CBD$ (chemical bath deposition) technique. Diffusion membranes were used to optimize the kinetic growth through a moderate control of release of metal ions into the work solution. As the conditions for the formation in one step of the $Cu_2SnS_3$ compound have not yet been reported in literature, special emphasis was put on finding the parameters that allow growing the $Cu_2SnS_3$ thin films by simultaneous precipitation of $Cu_2S$ and $SnS_2$. For that, we propose a methodology that includes numerical solution of the equilibrium equations that were established through a study of the chemical equilibrium of the system $SnCl_2$, $Na_3C_6H_5O_7\cdot 2H2O$, $CuCl_2$ and $Na_2S_2O_3\cdot5H_2O$. The formation of thin films of $CTS$ and $CZTS$ free of secondary phases grown with a stoichiometry close to that corresponding to the $Cu_2SnS_3$ and $Cu_2ZnSnS_4$ phases, was verified through measurements of X-ray diffraction $(XRD)$ and Raman spectroscopy. Solar cell with an efficiency of $4.2%$, short circuit current of $16.2 mA/cm^2$ and open-circuit voltage of 0.49 V was obtained.

Fabrication of Cu2ZnSnS4solar Cells with 5.1% Efficiency Via Thermal Decomposition and Reaction Using a Non-Toxic Sol–gel Route

Low-cost Fabrication of Cu 2 ZnSnS 4 Thin Films for Solar Cell Absorber Layers

Solution-Processed One-Dimensional ZnO@CdS Heterojunction toward Efficient Cu2ZnSnS4 Solar Cell with Inverted Structure

Fabrication of Cu 2 ZnSnS 4 thin films using oxides nanoparticles ink for solar cell

All-Layer Sputtering-Free Cu2Zn1-xCdxSnS4 Solar Cell with Efficiency Exceeding 7.5%

A 5.5% efficient co-electrodeposited ZnO/CdS/Cu 2 ZnSnS 4 /Mo thin film solar cell

8.36% Efficient CZTS Solar Cells on Transparent Electrode Via Solution Processing

Over 10% Efficiency Pure Sulfide Kesterite Solar Cells on Transparent Electrode with Cd-Ag Co-Alloying

Fabrication of a Cu2ZnSn(S,Se)4 photovoltaic device by a low-toxicity ethanol solution process.

Environmentally Friendly Synthesis of Copper Zinc Tin Sulfide (CZTS) Thin Film Solar Cells: Advancing Sustainable Photo-Energy Conversion with Low-Temperature Chemical Processing

A Strategy to Stabilize Kesterite Czts for High-Performance Solar Cells

Low-Temperature Plasma-Enhanced Atomic Layer Deposition of ZnMgO for Efficient CZTS Solar Cells

Fabrication of solar cells based on $Cu_2ZnSnS_4$ prepared from $Cu_2SnS_3$ synthesized using a novel chemical procedure

Solution transformation of SnS into Cu2ZnSnS4xSe4(1-x) for solar water splitting

Coordination Engineering of Cu-Zn-Sn-S Aqueous Precursor for Efficient Kesterite Solar Cells

Cd‐Free Pure Sulfide Kesterite Cu2ZnSnS4 Solar Cell with Over 800 mV Open‐Circuit Voltage Enabled by Phase Evolution Intervention

Preparation And Characterization Of Cu2znsns4 Thin Films And Solar Cells Fabricated From Quaternary Cu-Zn-Sn-S Target

Facile Growth of Cu2ZnSnS4 Thin-Film by One-Step Pulsed Hybrid Electrophoretic and Electroplating Deposition

Sol-gel synthesis of Cu2ZnSnS4 thin films under mild conditions

Improving the efficiency of Cu2ZnSnS4 solar cells by promoting the homogeneous distribution of Sn element

Toward High Efficient Cu2 ZnSn(Sx ,Se1- x )4 Solar Cells: Break the Limitations of VOC and FF