Abstract:To fulfill the combination of high strength and ductility, configuration of novel fiber-like structural TiB reinforced titanium matrix composites was designed and successfully fabricated through series of powder metallurgy and hot working process. The influence of the fiber-like structure and microstructures on the mechanical response is investigated to clarify their strengthening and plasticizing mechanisms. Smaller equiaxed α-Ti grains generated in both the composites region and Ti region of the TiB/Ti composites. The new configuration improved the tensile strength from 573.5 MPa to 659.1 MPa while the ductility (24.4%) was comparable with that of pure Ti (23.5%). Besides, prismatic <a> slips with Schmid factors above 0.4 had higher distribution in both the composites region and Ti region of the TiB/Ti composites than pure Ti along the loading direction, suggesting the higher deformation ability of the TiB/Ti composites. Moreover, the loading-unloading-reloading (LUR) true stress-strain curves showed much higher back stress in fiber-like structural TiB/Ti composites compared with unreinforced Ti during deformation. The existence of the back stress increased the strain hardening rate when the true strain was above 0.05 and strengthened the Ti region, which was caused by deformation incompatible between the composites region and Ti region during tensile loading in the TiB/Ti composites. The higher mechanical response of the TiB/Ti composites is attributed to the introduction of TiB reinforcements with the new fiber-like structure, and the coupling effect of consequent grain refinement, load transferring effect, dislocation pinning effect of the fine TiB particles, back stress strengthening and the higher Schmid factors of prismatic<a> slips.

Microstructure and tensile behavior of novel laminated Ti-TiBw/Ti composites by reaction hot pressing

In Situ TiBw/Ti–6Al–4V Composites with Novel Reinforcement Architecture Fabricated by Reaction Hot Pressing

In situ (TiBw+TiCp)/Ti6Al4V composites with a network reinforcement distribution

Fabrication of Fully Dense Tial-Based Composite Sheets with A Novel Microlaminated Microstructure

IN SITU TiBW/Ti COMPOSITES WITH A NOVEL QUASI- CONTINUOUS NETWORK REINFORCEMENT ARCHITECTURE

Gradient Grain Distribution and Enhanced Properties of Novel Laminated Ti–TiBw/Ti Composites by Reaction Hot-Pressing

Elastic and Plastic Behaviors of Laminated Ti-TiBw/Ti Composites

Fracture behaviors and microstructural failure mechanisms of laminated Ti–TiBw/Ti composites

Fabrication and mechanical properties of TiB w /Ti-Ti(Al) laminated composites

Microstructure and tensile properties of in situ synthesized (TiBw + TiCp)/Ti6242 composites

Synthesis and Mechanical Properties of Innovative (Tib/ti)-Ti3al Micro-Laminated Composites

Microstructure of In-Situ Synthesized (tib+tic)/ti Composites Prepared by Hot-pressing

Microstructure and Tensile Properties of in Situ (tib+tic)/ti6242 (tib:Tic=1:1) Composites Prepared by Common Casting Technique

Fabrication and characterization of laminated Ti-(TiB+La 2 O 3 )/Ti composite

Superplasitic Tensile Behavior of in Situ TiBw/Ti6Al4V Composite with Novel Network Microstructure

Microstructure and Mechanical Properties of In-situ Fabricated LaminatedTi-(TiB+TiC)/Ti Composites

Microstructure and superior mechanical property of in situ (TiBw + TiCp)/Ti composites with laminated structure

Fabrication, Microstructure Characterization and Fracture Behavior of a Unique Micro-Laminated TiB-TiAl Composites

Microstructural and Mechanical Properties of In-Situ Micro-Laminated TiC/Ti Composite Synthesised

Effects of Reinforcement Volume Fraction on Tensile Behaviors of Laminated Ti–TiBw/Ti Composites

Configuration of new fiber-like structure driven high matching of strength-ductility in TiB reinforced titanium matrix composites