Abstract:Bulk dense and fine-grained single-phase Ba 4 Ti 13 O 30 ceramic was successfully prepared by the mixed-phase two-step sintering (MP-TSS) method, and its dielectric properties and microwave performance were characterized in this paper. Influences of the solid-phase reaction on the sintering behavior of the mixed-phase sintering were explored during the first-step sintering. Effects of the first-step sintering regime, especially including the holding time at high temperatures, on the final quality of the ceramics were investigated by examining the density and microstructure at the end of the first step. Results showed that a rapidly completed solid-phase reaction and the formation of an equiaxed fine-grained microstructure were favorable for the MP-TSS method to obtain ceramics with high densities. The higher the density at the end of the first-step sintering in the MP-TSS process without significant grain growth, the more favorable it was for producing final high-density ceramics. The specimens sintered at 1230 °C/2 h–1180 °C/12 h exhibit optimal dielectric and microwave properties. Their dielectric constant and dielectric loss at 1 MHz are 50 and 0.0005, respectively, and the quality factor and temperature coefficient of resonant frequency at microwave are 43,550 and 39.4 ppm/°C, respectively. These findings aid in saving time for optimizing the TSS regime and producing ceramics using the TSS technology. The first-step holding time in the TSS process offers a technological choice of tuning the initial morphology of the second-step sintering to yield fully dense and fine-grained ceramics, and potentially expand the range of applications for TSS technology.

Ba0.6Sr0.4TiO3-MgO ceramics from ceramic powders prepared by improved aqueous gelcasting-assisted solid-state method

Ba 0.6 Sr 0.4 TiO 3- MgO ceramic powders with uniform microstructures prepared by aqueous gelcasting-assisted solid-state method

Microstructures and dielectric properties of Ba0.6Sr0.4TiO3–MgO ceramics prepared by non-aqueous gelcasting and dry pressing

The Effect of B2o3-Li2co3 Addition on Sintering Behavior and Dielectric Properties of Ba0.6sr0.4tio3 Ceramics

Enhanced low electric-field energy-storage performance in Ba0.9Sr0.1TiO3-Bi(Mg1/2Ti1/2)O-3 ceramics

Gelcasting of BaTiO3 ceramic powders

Improved Energy Storage Performance of Ba0.4Sr0.6TiO3 Nanocrystalline Ceramics Prepared by Using Oxalate Co-Precipitation and Spark Plasma Sintering

Highly enhanced sinterability of fine-grained Ba0.6Sr0.4TiO3−MgO bulk ceramics and in-situ nanocomposite thick films

The effect of Zn–B–Si–O addition on Ba0.7Sr0.3TiO3 by sol–gel process

Influence of solid loading on densification behavior, micromorphology and dielectric properties of Ba0.67Sr0.33TiO3 ceramics fabricated by a novel DCC-HVCI method

Bulk dense Ba4Ti13O30 ceramics prepared by mixed-phase two-step sintering method

Enhanced Energy Storage Properties of Barium Strontium Titanate Ceramics Prepared by Sol-Gel Method and Spark Plasma Sintering

Dielectric properties of Mg-doped Ba0.6Sr0.4TiO 3 ceramics prepared by using sol-gel derived powders

PREPARATION OF MULLITE-ALUMINIUM TITANATE CERAMIC COMPOSITES VIA GELCASTING

Anti-reduction of Ti 4+ in Ba 4.2Sm 9.2Ti 18O 54 ceramics by doping with MgO, Al 2O 3 and MnO 2

Microstructure and Dielectric Properties of Ba0.6sr0.4tio3 Ceramics Co-Doped Al2o3-Mgo

Enhanced Energy Storage Properties of Bi(Mg0.5Zr0.5)O3 Modified Ba0.9Sr0.1TiO3 Ceramics

Multifunctional Characteristics of BCTH:0.5% Sm3+ Ceramics Prepared via Hydrothermal Method and Powder Injection Molding

Effect of sintering temperature on microstructure, crystal structure and dielectric performance of Ba0.67Sr0.33TiO3 ceramics prepared by a novel direct coagulation casting via high valence counter ions (DCC-HVCI) method

Microstructures and dielectric properties of Ba[(Co0.7Zn0.3)1/3Nb2/3]O3-based ceramics prepared by aqueous gelcasting-assisted solid-state method

Preparation Process of BST Dielectric Ceramics