Abstract:Capacitive sensors are efficient tools for biophysical force measurement, which is essential for the exploration of cellular behavior. However, attention has been rarely given on the influences of external mechanical and internal electrical interferences on capacitive sensors. In this work, a bionic swallow structure design norm was developed for mechanical decoupling, and the influences of structural parameters on mechanical behavior were fully analyzed and optimized. A bionic feather comb distribution strategy and a portable readout circuit were proposed for eliminating electrostatic interferences. Electrostatic instability was evaluated, and electrostatic decoupling performance was verified on the basis of a novel measurement method utilizing four complementary comb arrays and application-specific integrated circuit readouts. An electrostatic pulling experiment showed that the bionic swallow structure hardly moved by 0.770 nm, and the measurement error was less than 0.009% for the area-variant sensor and 1.118% for the gap-variant sensor, which can be easily compensated in readouts. The proposed sensor also exhibited high resistance against electrostatic rotation, and the resulting measurement error dropped below 0.751%. The rotation interferences were less than 0.330 nm and (1.829 × 10 −7 )°, which were 35 times smaller than those of the traditional differential one. Based on the proposed bionic decoupling method, the fabricated sensor exhibited overwhelming capacitive sensitivity values of 7.078 and 1.473 pF/μm for gap-variant and area-variant devices, respectively, which were the highest among the current devices. High immunity to mechanical disturbances was maintained simultaneously, i.e., less than 0.369% and 0.058% of the sensor outputs for the gap-variant and area-variant devices, respectively, indicating its great performance improvements over existing devices and feasibility in ultralow biomedical force measurement.

Extending upper cutoff frequency of electrochemical seismometer by using extremely thin Su8 insulating spacers

Mechanical Design Optimization of A Single-Axis Moems Accelerometer Based on A Grating Interferometry Cavity for Ultrahigh Sensitivity

MEMS-Based Electrochemical Seismometer with a Sensing Unit Integrating Four Electrodes

MEMS-Based Electrochemical Seismometer Relying on a CAC Integrated Three-Electrode Structure

An Electrochemical, Low-Frequency Seismic Micro-Sensor Based on MEMS with a Force-Balanced Feedback System

The MEMS-Based Electrochemical Seismic Sensor With Integrated Sensitive Electrodes by Adopting Anodic Bonding Technology

Su8-waveguide Based Phase Corrected Fourier Transform Spectrometer Chip with Low Side Ripples

High‐precision Dielectric Sensor System Based on Balanced CSRR‐SIW Resonators

Temperature Compensation of the MEMS-Based Electrochemical Seismic Sensors

A MEMS Electrochemical Seismometer Based on the Integrated Structure of Centrosymmetric Four Electrodes

Enhanced Performance of ZnO/SiO 2 /Al 2 O 3 Surface Acoustic Wave Devices with Embedded Electrodes

Enhanced Performance Of Zno/Sio2/Al2o3 Surface Acoustic Wave Devices With Embedded Electrodes

Enhanced Coupling Coefficient in Dual-Mode ZnO/SiC Surface Acoustic Wave Devices with Partially Etched Piezoelectric Layer

High Sensitivity Micro Electrometer Based On Clamped Free Curved Beams Resonator With Weakened Nonlinearity

Vhf Cmos-Mems Oxide Resonators With Q > 10,000

Capillary effect-based selective sealing strategy for increasing piezoelectric MEMS speaker performance

A bionic approach for the mechanical and electrical decoupling of an MEMS capacitive sensor in ultralow force measurement

An Optical Interferometry Based MEMS Accelerometer Applicable to Seismic-Grade Measurement

Boosting electromagnetic wave absorption properties via the sulfidation strategy of Fe/Fe3C/N-doped carbon nanorods hybrids

A Direct-Reading MEMS Conductivity Sensor with a Parallel-Symmetric Four-Electrode Configuration

Thickness shear mode quartz crystal resonators with optimized elliptical electrodes