Abstract:The fabrication process of integral ceramic mold based on stereolithography and gelcasting can eliminate the assembly errors between cores and that between cores and shell in the traditional manufacturing process of ceramic molds. However, the bending strength of the mold at 500 degrees C (mid-temperature strength) drops significantly during pre-sintering because the gel networks surrounded the ceramic particles are burnt off, which often causes the core fracture or shell cracking of the integral ceramic mold. In this paper, short alumina-based fibers were added into the gelcast ceramic slurry to improve the mid-temperature of the ceramic mold. Filling experiment and computed tomography (CT) test were performed to investigate the effect of fiber content and fiber length on the filling ability of ceramic slurry in the cavity with small complex structures. The mid-temperature strengths of the ceramic mold were tested. Microstructures of the ceramic mold sintered at 500 degrees C were observed by scanning electron microscope (SEM). It was found that the filling ability of the ceramic slurry decreased as the fiber length and fiber content increased, however the mid-temperature strength of the ceramic mold increased with the fiber length and fiber content. When 1.5wt% short alumina-based fibers with lengths between 0.5 mm and 1 mm were added, the ceramic slurry could meet the requirement of gelcasting, and the mid-temperature strength of the ceramic mold was improved from 0.78 MPa to 1.65 MPa.

The effect of SiC whisker on the performances of Al2O 3 matrixceramics mould for hollow turbine blade

Effect of in Situ Synthesised Mullite Whiskers on the High-Temperature Strength of Al2o3-Based Ceramic Moulds for Casting Hollow Turbine Blades

Effect of Urchin-Like Mullite Whiskers on the High-Temperature Performance of Porous SiO<sub>2</sub>-Based Ceramic Molds

Effect of Urchin-Like Mullite Whiskers on the High-Temperature Performance of Porous SiO₂-Based Ceramic Molds.

Improvement of mechanical properties of Al2O3/Ti3SiC2 multilayer ceramics by adding SiC whiskers into Al2O3 layers

Effects of Adding Aluminum Oxide or Zirconium Oxide Fibers on Ceramic Molds for Casting Hollow Turbine Blades

Preparation and mechanical properties of SiC whisker-reinforced alumina

The Effect of SiC Whisker on the Sintering and Thermal Shock Resistance Property of ZrO2-mullite Ceramic

Mechanical Properties of Silicon Carbide Whisker-Reinforced Silicon Nitride Matrix Composites

The Effect of Sintering Additive on Fracture Behavior of Carbon-Whisker-reinforced Silicon Carbide Composites

Curing behaviors and mechanical properties of SiC-whisker-reinforced alumina ceramics fabricated with digital light processing

The preparation of mullite foamed ceramics reinforced by in-situ SiC whiskers and their reinforcement mechanism

Effect Of Alumina-Based Fiber On The Mid-Temperature Strength Of Integral Ceramic Mold For Casting Hollow Turbine Blade

Effect of Heating Parameters on Sintering Behaviors and Properties of Mullite Whisker Frameworks

Microstructure and properties of silicon carbide whisker reinforced zirconium diboride ultra-high temperature ceramics

Microstructure and Mechanical Properties of Sic Whisker-Reinforced Zrb2 Ultra-High Temperature Ceramic

Preparation and Mechanical Properties of SiC Whisker and Nanosized Mullite Particulate Reinforced TZP Composites

Interface Structure and Mechanical Properties of Al2O3–20vol%SiCw Ceramic Matrix Composite

Effect of SiC Nano-Whisker Addition on WC–Ni Based Cemented Carbides Fabricated by Hot-Press Sintering

Microstructure and mechanical properties of barium aluminosilicate glass-ceramic matrix composites reinforced with SiC whiskers

Synergistic Toughening Effect of SiC Whiskers and Particles in ZrO2–Al2O3–SiC Ceramics