Abstract:The hot deformation behaviors of single- and two-phase CuAlMn shape memory alloy were studied. Isothermal compression tests were conducted at different temperatures from 400<math>°C</math> to 800<math>°C</math> and various strain rates from 0.001/S to 1/S. At the temperature below 500<math>°C</math>, CuAlMn alloy had a two-phase microstructure (FCC <math>α</math> phase + <math>L21</math> <math>β</math> phase); while at the temperature higher than 550<math>°C</math>, the alloy had a single <math>β</math> phase structure. The flow stress curves showed the stress drop for all samples, indicating a dynamic recrystallization (DRX) feature of the alloy. The local minimum value of stress drop appeared at 500<math>°C</math>. The thermal active energy (<math>Q</math>) were calculated to be <math>418.7 kJ mol−1</math> for <math>α+β</math> alloy at 400–500<math>°C</math> and <math>219.7 kJ mol−1</math> for <math>β</math> alloy at 550–800<math>°C</math>, respectively. The artificial neural network (ANN) model showed a high precision to predict the flow stress of the studied alloy at a wide range of temperature. Based on the dynamic material model (DMM) theory, the processing map of the alloy that consists of the contour lines of the power dissipation factor, <math>η</math>, and the instability criteria was established. The grains were refined to a micron level and DRX of <math>α</math> phase occurred during the deformation between 400–500<math>°C</math> at the low strain rate. The hot deformation behaviors of the alloy at the low temperature (400–450<math>°C</math>) mainly depended on the deformation of <math>α</math> phase. The optimum deformation parameters for the single-phase CuAlMn alloys were 750–800<math>°C</math>/0.1–1 s−1.

Rate dependent damping of single crystal CuAlNi shape memory alloy

Stabilization of deformed stress-induced martensite and its effect on shape memory effect in an Fe-Mn-Si-Ni-Co alloy

Rate Dependence of Temperature Fields and Energy Dissipations in Non-Static Pseudoelasticity

Experimental Investigation on Rate Dependence of Thermomechanical Response in Superelastic NiTi Shape Memory Alloy

Temperature Effects on Deformation Substructures and Mechanisms of a Ni-based Single Crystal Superalloy

Thermomechanical coupling in cyclic phase transition of shape memory material under periodic stressing—experiment and modeling

In-situ TOF Neutron Diffraction Studies of Cyclic Softening in Superelasticity of a NiFeGaCo Shape Memory Alloy

Hot deformation behavior of a CuAlMn shape memory alloy

Research on Damping Characteristics of Ternary Ti49.2Ni49.3Co1.5 Shape Memory Alloy

Effect of Heating/Cooling Rate on the Transformation Temperatures in Tinicu Shape Memory Alloys

A Study of a Cryogenic CuAlMn Shape Memory Alloy

In Situ Observation on Temperature Dependence of Martensitic Transformation and Plastic Deformation in Superelastic NiTi Shape Memory Alloy

Microstructure, Martensitic Transformation And Superelasticity Of T1(49) (6)N1(45 1)Cu(5)Cr(0 3) Shape Memory Alloy

Effect of Cyclic Loading on Apparent Young's Modulus and Critical Stress in Nano-Subgrained Superelastic NiTi Shape Memory Alloys

Effect of Aging on Martensitic Transformation and Superelasticity of TiNiCr Shape Memory Alloy

Neutron Diffraction Study on Strain Rate Dependent Mechanical Response in Superelastic NiTi Alloy: Bulk Structural Evolution and Constitutive Model

Effect of Ni alloying on vacancy behavior and damping capacity in martensitic ductile Cu–Al–Mn alloys

Strain intermittency in shape-memory alloys

Influence of applied stress on shape memory characteristics of Ni50Ti45Cu5 (at.%) alloy subjected to thermomechanical cycling

Effects of cooling rate on martensitic transformation behavior and shape memory property for Ni-rich NiTiHf-Nb high-temperature shape memory alloy

Local Mechanical Response of Superelastic NiTi Shape-Memory Alloy Under Uniaxial Loading